Catalysts, fluidized beds

Amination by ammonolysis, G, solid catalyst, fluidized bed [-650 MJ/kmol] 440 °C, 4 s (acrylontrile, 5 data) rate doubles 30 °C for the range 400-550 °C multitube fixed catalyst bed [-650 MJ/kmol] 230 °C, 4 s (acrylonitrile, ethyl amine, 4 data) rate doubles in 25 °C for the range 150-250 °C. 

However, if high rates of heat transfer are required or the catalyst requires frequent regeneration, then fixed beds are not suitable, and under these circumstances, a fluidized bed is preferred, as we shall discuss later. 

In addition to the advantage of high heat transfer rates, fluidized beds are also useful in situations where catalyst particles need frequent regeneration. Under these circumstances, particles can be removed continuously from the bed, regenerated, and recycled back to the bed. In exothermic reactions, the recycling of catalyst can be... 

Figure 2.8 A fluidized-bed reactor allows the catalyst to be continuously withdrawn and regenerated as with the refinery catalytic cracker.

Fluidized-bed catalytic reactors tend to generate loss of catalyst through attrition of the solid particles, causing fines to be generated. 

Recent advances in Eischer-Tropsch technology at Sasol include the demonstration of the slurry-bed Eischer-Tropsch process and the new generation Sasol Advanced Synthol (SAS) Reactor, which is a classical fluidized-bed reactor design. The slurry-bed reactor is considered a superior alternative to the Arge tubular fixed-bed reactor. Commercial implementation of a slurry-bed design requires development of efficient catalyst separation techniques. Sasol has developed proprietary technology that provides satisfactory separation of wax and soHd catalyst, and a commercial-scale reactor is being commissioned in the first half of 1993. 

M ass Transfer. Mass transfer in a fluidized bed can occur in several ways. Bed-to-surface mass transfer is important in plating appHcations. Transfer from the soHd surface to the gas phase is important in drying, sublimation, and desorption processes. Mass transfer can be the limiting step in a chemical reaction system. In most instances, gas from bubbles, gas voids, or the conveying gas reacts with a soHd reactant or catalyst. In catalytic systems, the surface area of a catalyst can be enormous. Eor Group A particles, surface areas of 5 to over 1000 m /g are possible. 

Bed-to-Surface Heat Transfer. Bed-to-surface heat-transfer coefficients in fluidized beds are high. In a fast-fluidized bed combustor containing mostly Group B limestone particles, the dense bed-to-boiling water heat-transfer coefficient is on the order of 250 W/(m -K). For an FCC catalyst cooler (Group A particles), this heat-transfer coefficient is around 600 W/(600 -K). 

Natural Gas Upgrading via Fischer-Tropsch. In the United States, as in other countries, scarcities from World War II revived interest in the synthesis of fuel substances. A study of the economics of Fischer synthesis led to the conclusion that the large-scale production of gasoline from natural gas offered hope for commercial utiHty. In the Hydrocol process (Hydrocarbon Research, Inc.) natural gas was treated with high purity oxygen to produce the synthesis gas which was converted in fluidized beds of kon catalysts (42). 

Fluidized-bed reactor systems put other unique stresses on the VPO catalyst system. The mixing action inside the reactor creates an environment that is too harsh for the mechanical strength of a vanadium phosphoms oxide catalyst, and thus requires that the catalyst be attrition resistant (121,140,141). To achieve this goal, vanadium phosphoms oxide is usually spray dried with coUoidal siUca [7631-86-9] or polysiUcic acid [1343-98-2]. Vanadium phosphoms oxide catalysts made with coUoidal sUica are reported to have a loss of selectivity, while no loss in selectivity is reported for catalysts spray dried with polysUicic acid (140). 

Fluidized-bed reaction systems are not normally shut down for changing catalyst. Fresh catalyst is periodically added to manage catalyst activity and particle size distribution. The ALMA process includes faciUties for adding back both catalyst fines and fresh catalyst to the reactor. 

Fresh butane mixed with recycled gas encounters freshly oxidized catalyst at the bottom of the transport-bed reactor and is oxidized to maleic anhydride and CO during its passage up the reactor. Catalyst densities (80 160 kg/m ) in the transport-bed reactor are substantially lower than the catalyst density in a typical fluidized-bed reactor (480 640 kg/m ) (109). The gas flow pattern in the riser is nearly plug flow which avoids the negative effect of backmixing on reaction selectivity. Reduced catalyst is separated from the reaction products by cyclones and is further stripped of products and reactants in a separate stripping vessel. The reduced catalyst is reoxidized in a separate fluidized-bed oxidizer where the exothermic heat of reaction is removed by steam cods. The rate of reoxidation of the VPO catalyst is slower than the rate of oxidation of butane, and consequently residence times are longer in the oxidizer than in the transport-bed reactor. 

Polymerization in the Gas Phase. Many polymerization catalysts can be adapted for use in the gas phase. A gas-phase reactor contains a bed of small PE particles that is agitated either by a mechanical stirrer or by employing the fluidized-bed technique. These processes are economical because they do not requite solvent tecitculation streams. 

Heterogeneous hydrogenation catalysts can be used in either a supported or an unsupported form. The most common supports are based on alurnina, carbon, and siUca. Supports are usually used with the more expensive metals and serve several purposes. Most importandy, they increase the efficiency of the catalyst based on the weight of metal used and they aid in the recovery of the catalyst, both of which help to keep costs low. When supported catalysts are employed, they can be used as a fixed bed or as a slurry (Uquid phase) or a fluidized bed (vapor phase). In a fixed-bed process, the amine or amine solution flows over the immobile catalyst. This eliminates the need for an elaborate catalyst recovery system and minimizes catalyst loss. When a slurry or fluidized bed is used, the catalyst must be separated from the amine by gravity (settling), filtration, or other means. 

Direct Process. Passing methyl chloride through a fluidized bed of copper and siUcon yields a mixture of chlorosilanes. The rate of methylchlorosilane (MCS) production and chemical selectivity, as determined by the ratio of dimethydichlorosilane to the other compounds formed, are significantly affected by trace elements in the catalyst bed very pure copper and siUcon gives poor yield and selectivity (22). 

In oxychlorination, ethylene reacts with dry HCl and either air or pure oxygen to produce EDC and water. Various commercial oxychlorination processes differ from one another to some extent because they were developed independentiy by several different vinyl chloride producers (78,83), but in each case the reaction is carried out in the vapor phase in either a fixed- or fluidized-bed reactor containing a modified Deacon catalyst. Unlike the Deacon process for chlorine production, oxychlorination of ethylene occurs readily at temperatures weU below those requited for HCl oxidation. 

Process water streams from vinyl chloride manufacture are typically steam-stripped to remove volatile organics, neutralized, and then treated in an activated sludge system to remove any nonvolatile organics. If fluidized-bed oxychlorination is used, the process wastewater may also contain suspended catalyst fines and dissolved metals. The former can easily be removed by sedimentation, and the latter by precipitation. Depending on the specific catalyst formulation and outfall limitations, tertiary treatment may be needed to reduce dissolved metals to acceptable levels. 

---