Carbon shift reactions

As discussed above, camphene hydrochloride suffers from steric strain as a result of two buttressing interactions leading to relatively easy heterolysis of the carbon-chlorine bond. If the material is kept cool enough to prevent the Wagner-Meerwein and subsequent elimination reaction from occurring, what can happen is a simple 1,2-carbon shift reaction. This is shown in Figure 5.35 starting from one enantiomer... 

Another hydrogenation process utilizes internally generated hydrogen for hydroconversion in a single-stage, noncatalytic, fluidized-bed reactor (41). Biomass is converted in the reactor, which is operated at about 2.1 kPa, 800°C, and residence times of a few minutes with steam-oxygen injection. About 95% carbon conversion is anticipated to produce a medium heat value (MHV) gas which is subjected to the shift reaction, scmbbing, and methanation to form SNG. The cold gas thermal efficiencies are estimated to be about 60%. 

Study of the mechanism of this complex reduction-Hquefaction suggests that part of the mechanism involves formate production from carbonate, dehydration of the vicinal hydroxyl groups in the ceUulosic feed to carbonyl compounds via enols, reduction of the carbonyl group to an alcohol by formate and water, and regeneration of formate (46). In view of the complex nature of the reactants and products, it is likely that a complete understanding of all of the chemical reactions that occur will not be developed. However, the Hquefaction mechanism probably involves catalytic hydrogenation because carbon monoxide would be expected to form at least some hydrogen by the water-gas shift reaction. 

The mixture of carbon monoxide and hydrogen is enriched with hydrogen from the water gas catalytic (Bosch) process, ie, water gas shift reaction, and passed over a cobalt—thoria catalyst to form straight-chain, ie, linear, paraffins, olefins, and alcohols in what is known as the Fisher-Tropsch synthesis. 

Prior to methanation, the gas product from the gasifier must be thoroughly purified, especially from sulfur compounds the precursors of which are widespread throughout coal (23) (see Sulfurremoval and recovery). Moreover, the composition of the gas must be adjusted, if required, to contain three parts hydrogen to one part carbon monoxide to fit the stoichiometry of methane production. This is accompHshed by appHcation of a catalytic water gas shift reaction. 

Synthesis Gas Chemicals. Hydrocarbons are used to generate synthesis gas, a mixture of carbon monoxide and hydrogen, for conversion to other chemicals. The primary chemical made from synthesis gas is methanol, though acetic acid and acetic anhydride are also made by this route. Carbon monoxide (qv) is produced by partial oxidation of hydrocarbons or by the catalytic steam reforming of natural gas. About 96% of synthesis gas is made by steam reforming, followed by the water gas shift reaction to give the desired H2 /CO ratio. 

Synthesis gas, a mixture of CO and o known as syngas, is produced for the oxo process by partial oxidation (eq. 2) or steam reforming (eq. 3) of a carbonaceous feedstock, typically methane or naphtha. The ratio of CO to may be adjusted by cofeeding carbon dioxide (qv), CO2, as illustrated in equation 4, the water gas shift reaction. 

Synthesis gas preparation consists of three steps ( /) feedstock conversion, (2) carbon monoxide conversion, and (2) gas purification. Table 4 gives the main processes for each of the feedstocks (qv) used. In each case, except for water electrolysis, concommitant to the reactions shown, the water-gas shift reaction occurs. 

Shift Conversion. Carbon oxides deactivate the ammonia synthesis catalyst and must be removed prior to the synthesis loop. The exothermic water-gas shift reaction (eq. 23) provides a convenient mechanism to maximize hydrogen production while converting CO to the more easily removable CO2. A two-stage adiabatic reactor sequence is normally employed to maximize this conversion. The bulk of the CO is shifted to CO2 in a high... 

HTS catalyst consists mainly of magnetite crystals stabilized using chromium oxide. Phosphoms, arsenic, and sulfur are poisons to the catalyst. Low reformer steam to carbon ratios give rise to conditions favoring the formation of iron carbides which catalyze the synthesis of hydrocarbons by the Fisher-Tropsch reaction. Modified iron and iron-free HTS catalysts have been developed to avoid these problems (49,50) and allow operation at steam to carbon ratios as low as 2.7. Kinetic and equiUbrium data for the water gas shift reaction are available in reference 51. 

This is the reverse of the water-gas shift reaction in the production of hydrogen and ammonia (qv). Carbon dioxide may also be reduced catalyticaHy with various hydrocarbons and with carbon itself at elevated temperatures. The latter reaction occurs in almost all cases of combustion of carbonaceous fuels and is generally employed as a method of producing carbon monoxide. 

Conversion to Hydrogen (Water Gas Shift Reaction). Carbon monoxide reacts with water over a catalyst to produce hydrogen and carbon monoxide (25). This reaction is used to prepare high purity hydrogen or synthesis gas with a higher hydrogen-to-carbon monoxide ratio than the feed (eq. 3). 

Steam reforming is the reaction of steam with hydrocarbons to make town gas or hydrogen. The first stage is at 700 to 830°C (1,292 to 1,532°F) and 15-40 atm (221 to 588 psih A representative catalyst composition contains 13 percent Ni supported on Ot-alumina with 0.3 percent potassium oxide to minimize carbon formation. The catalyst is poisoned by sulfur. A subsequent shift reaction converts CO to CO9 and more H2, at 190 to 260°C (374 to 500°F) with copper metal on a support of zinc oxide which protects the catalyst from poisoning by traces of sulfur. 

Hydrogen and carbon monoxide are produced by the gasification reaction, and they react with each other and with carbon. The reaction of hydrogen with carbon as shown in reaction (27-15) is exothermic and can contribute heat energy. Similarly, the methanation reaction (27-19) can contribute heat energy to the gasification. These equations are interrelated by the water-gas-shift reaction (27-18), the equilibrium of which controls the extent of reactions (27-16) and (27-17). 

CO2 can be readily obtained in small amounts by the action of acids on carbonates. On an industrial scale the main source Is as a byproduct of the synthetic ammonia process in which the H2 required is generated either by the catalytic reaction (a) or by the water-gas shift reaction (b) ... 

Tile CH carbon shift ranges between S 62.4 and 95.1 ppm and is typical of carbons carrying two electronegative substituents. Tliis could be a hint for the observed overall ease of substitution reaction at this center. However, electronic and structural properties of these substituents cause no characteristic differences in the S values. 

The carbon monoxide can then be further reacted with steam and/or hydrogen in the water gas shift reaction ... 

The coproduct water reacts with carbon monoxide (the shift reaction), yielding hydrogen and carbon dioxide ... 

The gained hydrogen from the water shift reaction reduces the hydrogen demand for FTS. Water gas shift proceeds at about the same rate as the FT reaction. Studies of the overall water shift reaction in FT synthesis have been reviewed by Rofer Deporter. Another side reaction also occurring in FTS reactors is the disproportionation of carbon monoxide to carbon dioxide and carbon ... 

Steam-Moderated Process. The basic idea behind this approach is to limit the extent of conversion of the methanation reaction, Reaction 1, by adding steam to the feed gases. This process simultaneously provides for (46) elimination of the CO shift, Reaction 2, to get a 3 1 H2 CO ratio from the make-up gas ratio of about 1.5 1 and avoidance of carbon laydown by operation under conditions in which carbon is not a thermodynamically stable phase (see Chemistry and Thermodynamics section above). 

An examination of some laboratory runs with diluted C150-1-02 catalyst can illustrate this problem. In one run with 304°C at inlet, 314 °C at exit, and 97,297 outlet dry gas space velocity, the following results were obtained after minor corrections for analytical errors. Of the CO present (out of an inlet 2.04 mole % ), 99.9885% disappeared in reaction while the C02 present (from an initial 1.96%) increased by over 30%. Equilibrium carbon oxides for both methanation reactions were essentially zero whereas the equilibrium CO based on the water-gas shift reaction at the exit composition was about one-third the actual CO exit of 0.03 mole %. From these data, activities for the various reactions may be estimated on the basis of various assumptions (see Table XIX for the effect of two different assumptions). 

Effects of Cold Gas Recycle and Approach to Equilibrium. Product gases resulting from various CGR ratios were analyzed (Table XI). For the experiments tabulated, a decrease in the cold recycle ratio resulted consistently in increases in the product gas concentrations of water vapor, hydrogen, and carbon dioxide and a decrease in methane concentration. These trends may be noted in experiment HGR-12 as the CGR ratio decreased from 8.7 1 to 1.2 1, in experiment HGR-13 as it increased from 1.0 1 to 9.1 1, and in experiment HGR-14 as it decreased from 3.0 1 to 1.0 1. These trends indicate that the water-gas shift reaction (CO + H20 —> C02 + H2) was sustained to some degree. Except for the 462-hr period in experiment HGR-14, the apparent mass action constants for the water-gas shift reaction (based on the product gas compositions in Table XI) remained fairly constant at 0.57-1.6. These values are much lower than the value of 11.7 for equilibrium conversion at 400°C. In... 

There is no separate shift conversion system and no recycle of product gas for temperature control (see Figure 1). Rather, this system is designed to operate adiabatically at elevated temperatures with sufficient steam addition to cause the shift reaction to occur over a nickel catalyst while avoiding carbon formation. The refractory lined reactors contain fixed catalyst beds and are of conventional design. The reactors can be of the minimum diameter for a given plant capacity since the process gas passes through once only with no recycle. Less steam is used than is conventional for shift conversion alone, and the catalyst is of standard ring size (% X %= in). 

For a clearer understanding of the behavior of syngases in a shift converter, we established another set of carbon isotherms when considering the shift reaction only (without methanation) in addition to the carbon-forming reactions. Figure 6 shows isotherms at a partial pressure of 270 psia for all components of a gas mixture, but excluding methane. 

---