Calcium types

Phosphatic limestone is usually a high calcium type that contains appreciable percentages (up to 5%) phosphoms. It originates from invertebrate marine organisms. 

Except for dead-burned dolomite, all limes are much more reactive with acids than limestone. The high calcium types are the most reactive. 

Ca.ustlciZa.tlon, Time, particularly the high calcium type, reacts with carbonates such as Na2C02 and Li2C02 to form other hydroxides and carbonates through double decomposition or metathesis reactions as foUow ... 

Ion channels Calcium (type N), calcium (type T and L), chloride, potassium (low conduct). 

Ho, M.W., Kaetzel, M. A., Armstrong, D.L. and Shears, S.B., 2001, Regulation of a human chloride channel, a paradigm for integrating input from calcium, type II calmodulin-dependent protein kinase, and inositol 3,4,5,6-tetrakisphosphate. J. Biol. Chem. 276 18673-18680. 

Some special dietetic packs are prepared with artificial sweeteners. Saccharin, benzoylsulfonic imide has been used since the eighties of the last century. More recently a new nonnutritive substance, sucaryl, the sodium salt of cyclohexane-sulfonic acid, has been produced in two forms—Sucaryl sodium and Sucaryl calcium. The calcium type is proposed for those whose ordinary salt ration should... 

To a large extent calcium anode thermal batteries are being displaced by ones using lithium rich alloys as discussed below. Lithium types avoid unwanted side reactions which characterize the calcium types which have electrochemical elEciencies down to 20% of theoretical values. 

In using the alkylphenols, it is possible to obtain three types of detergents the alkylphenols themselves transformed as salts of calcium, the alkylphenol-sulfides conferring antioxidant properties and finally the alkylphenol-sulfides transformed by action of CO2 into alkylsalicylate-sulfides (Figure 9.9). 

Qualitative examples abound. Perfect crystals of sodium carbonate, sulfate, or phosphate may be kept for years without efflorescing, although if scratched, they begin to do so immediately. Too strongly heated or burned lime or plaster of Paris takes up the first traces of water only with difficulty. Reactions of this type tend to be autocat-alytic. The initial rate is slow, due to the absence of the necessary linear interface, but the rate accelerates as more and more product is formed. See Refs. 147-153 for other examples. Ruckenstein [154] has discussed a kinetic model based on nucleation theory. There is certainly evidence that patches of product may be present, as in the oxidation of Mo(lOO) surfaces [155], and that surface defects are important [156]. There may be catalysis thus reaction VII-27 is catalyzed by water vapor [157]. A topotactic reaction is one where the product or products retain the external crystalline shape of the reactant crystal [158]. More often, however, there is a complicated morphology with pitting, cracking, and pore formation, as with calcium carbonate [159]. 

Allyl Bromide. Introduce into a 1-litre three-necked flask 250 g. (169 ml.) of 48 per cent, hydrobromic acid and then 75 g. (40-5 ml.) of concentrated sulphuric acid in portions, with shaking Anally add 58 g. (68 ml.) of pure allyl alcohol (Section 111,140). Fit the flask with a separatory funnel, a mechanical stirrer and an efficient condenser (preferably of the double surface type) set for downward distillation connect the flask to the condenser by a wide (6-8 mm.) bent tube. Place 75 g. (40 5 ml.) of concentrated sulphuric acid in the separatory funnel, set the stirrer in motion, and allow the acid to flow slowly into the warm solution. The allyl bromide will distil over (< 30 minutes). Wash the distillate with 5 per cent, sodium carbonate solution, followed by water, dry over anhydrous calcium chloride, and distil from a Claisen flask with a fractionating side arm or through a short column. The yield of allyl bromide, b.p. 69-72°, is 112 g. There is a small high-boiling fraction containing propylene dibromide. 

The experimental conditions for conducting the above reaction in the presence of dimethylformamide as a solvent are as follows. In a 250 ml. three-necked flask, equipped with a reflux condenser and a tantalum wire Hershberg-type stirrer, place 20 g. of o-chloronitrobenzene and 100 ml. of diinethylform-amide (dried over anhydrous calcium sulphate). Heat the solution to reflux and add 20 g. of activated copper bronze in one portion. Heat under reflux for 4 hours, add another 20 g. portion of copper powder, and continue refluxing for a second 4-hour period. Allow to cool, pour the reaction mixture into 2 litres of water, and filter with suction. Extract the solids with three 200 ml. portions of boiling ethanol alternatively, use 300 ml. of ethanol in a Soxhlet apparatus. Isolate the 2 2- dinitrodiphenyl from the alcoholic extracts as described above the 3ueld of product, m.p. 124-125°, is 11 - 5 g. 

A broad comparison of the main types of processes, the strength and quaUty of phosphoric acid, and the form and quaUty of by-product calcium sulfate are summarized in Table 7. Because the dihydrate process is the most widely used, the quaUty of its acid and calcium sulfate and its P2O3 recovery are taken as reference for performance comparisons. Illustrative flow diagrams of the principal variations in process types have been pubUshed (39). Numerous other variations in process details ar also used (40—42). The majority of plants use a dihydrate process and some of these have production capacity up to 2100 of P2O3 per day. 

High alpha-ceUulose chemical woodpulp paper, machine-made primarily from fast-growiag softwoods, sized usiag alkaline calcium compounds, and loaded with fillers and other additives, constitutes a presumably more stable material. Different types of paper are used for art, manuscripts, documents, books, etc, each having its own properties of color, texture, feel, etc. 

Submerged-Arc Furnace. Furnaces used for smelting and for certain electrochemical operations are similar in general design to the open-arc furnace in that they are usually three-phase, have three vertical electrode columns and a shell to contain the charge, but dkect current may also be utilised They are used in the production of phosphoms, calcium carbide, ferroalloys, siUcon, other metals and compounds (17), and numerous types of high temperature refractories. 

Succinimides. Ethosuximide [77-67-8] C2H22NO2 (41) and the related succinknide, methsuximide [77-41-8] C22H23NO2 (42) are used in absence seizure treatment. Like the other anticonvulsants discussed, the mechanism of action of the succinirnides is unclear. Effects on T-type calcium channels and -ATPase activity have been reported (20). Ethosuximide has significant CNS and gastrointestinal (GI) side effect HabiUties (13). 

Fillers. These are used to reduce cost in flexible PVC compounds. It is also possible to improve specific properties such as insulation resistance, yellowing in sunlight, scuff resistance, and heat deformation with the use of fillers (qv). Typical filler types used in PVC are calcium carbonate, clays, siHca, titanium dioxide, and carbon black. 

---