Burst test

Afterwards, the vessels were pressurized according a proof test and a burst test with acoustic emission measurements. Acoustic emission data recorded during these tests are analysed in order to determine assessment criteria. The criteria are mainly based on ... 

The defect was detected and located during the proof test, and acoustic emission could follow its evolution until 20 bars during the burst test. After the pressure, the evolution of defect stopped till the burst. This test confirm the capability of acoustic emission to detect the evolution of defect during a pneumatic test with a sufficiently wide margin relative to the burst pressure. 

Bursting tests have been carried out on neatly a hundred thick-walled cylinders made of carbon, low alloy, and stainless steels, together with some nonferrous materials. The diameter ratio of the cylinders varied from 1.75 to 5.86, and some tests were carried out at 660°C. An analysis of the results (19) showed that 90% of the cylinders burst within 15% of the value given by equation 17. 

This behef is supported by the results of burst tests on tubular specimens made of AISI 4335 tempered to various fracture toughness levels from... 

For knitted fabrics exhibiting high extensibiUty to failure, the ball burst test is recommended (ASTM D3787). A poHshed steel ball is pressed onto a rigidly held circle of knitted fabric. The force on the ball required to mpture the fabric is reported as breaking strength. 

Rupture discs are typically manufactured to order, where each order represents a lot. The ASME Code defines three mediods of acceptance testing for rupture discs. The most common method requires dial at least two discs from the lot be burst tested at the specified disc temperature. The results of these tests must fall within the rupture tolerance. Table 12-5 shows the changes between the old requirements and the new sizing methodology and certification process. 

Giesbrecht, H., K. Hess, W. Leuckel, and B. Maurer, 1981. Analysis of explosion hazards on spontaneous release of inflammable gases into the atmosphere. Part 1 Propagation and deflagration of vapor clouds on the basis of bursting tests on model vessels. Ger. Chem. Eng. 4 305-314. 

Zerplatzprobe, /. bursting test, zerpulvem, v.t. pulverize, zerquetschen, v.t. crush, mash, bruise. 

The certification of disk performance is to be based on actual bursting tests of two or more disks from a lot of the same material of the exact same size as the disk to be sold by the manufacturer. The holder for the test disks must be identical to the design, dimensions, etc., for the disk being certified. (See details ASME code. Par. UG-127 [1]). 

As allowed by code [1], the average of the manufacturer s disks burst tests could be stamped, for example, (144 + 160.5)/2 = 152.3 psig with an actual 5% of 152.3 psig allowed for actual burst pressure of any disk at the operating temperature. 

The weep point or strain-to-first-crack in a wall for filament-wound pipe constructed using isophthalic plastic is currently found to be not less than 0.009 in./in. This has been repeatedly demonstrated by careful coupon testing and burst testing of pipes with strain gauge instrumentation attached. 

A. Mackenzie E.W. Dalrymple, Burst Test Results Simplify Design of Irradiation Capsules for Explosive Materials , Nucle-... 

The seal and burst test values of identical packages produced on a specified validated production packaging line are useful data for performance specifications. The standardized methods of the American Society for Testing of Materials (ASTM) may be used. 

Burst test ASTM D-1140—Failure Resistance of Unrestrained and Nonrigid Packages for Medical Applications. The standard provides... 

When correctly selected and used, the methods for seal, leak, and burst testing are the essential tools available to the manufacturer to assist in providing... 

First prototypes were pressure-tested in a burst test of more than 60 bar. The pressure drop amounted to 110 mbar at a flow rate 3 1 min-1. As an example, an eight AMD 2000+ CPU with 70 W thermal power is cooled with eight plates of the above-given... 

LWR tests-to-failure had been performed to evaluate accident scenarios involving loss of coolant accident (LOCA) events such as occurred in the Three Mile Island incident. The power burst tests in a 20 MWt PWR have created fuel failures and defined the initiating conditions. The LOCA tests with a 50 MWt... 

A well-made PVC pipe has outside diameter 150 mm and wall thickness 15 mm. Measurements on this pipe give K c = 2.4 MPa m / and yield stress, ay = 50 MN Assume that the largest flaws are 100-/im cracks and that the calibration factor for the specimens used to measure fracture toughness is 1.12. The pipe is subjected to a test in which the internal pressure is gradually raised until the pipe fails. Will the pipe fail by yielding or brittle fracture in this burst test At what pressure will the pipe rupture ... 

In the burst test a flat sheet of paper is clamped by a cireumferential ring and a small rubber diaphragm underneath is gradually inflated with fluid, foreing the sheet to bulge until it ruptures. The hydrostatic pressure at the moment of failure is measured. The virtues of the burst test are its simplicity and the speed with which it can be undertaken. The reeorded hydraulic pressure offers a quantitative measure of bonding between fibres. It is linearly related to tensile strength. 

Grain can also be detected by a Mullen burst test (and tensile strength)—see Paper and board testing below. 

---