Benzene in hydrogenation

In this paper it is shown that the growth of carbon deposits can be maintained for long periods of time in the presence of hydrogen. The effect of hydrogen on the kinetics of carbon formation from benzene in hydrogen has been studied in experiments using nickel and iron foils. The results are presented below. 

The present research is an attempt to elucidate the mechanism of surface carbon deposition from benzene in hydrogen at atmospheric pressure and in the temperature range 800 to 1050°C. 

Strongly acidic media. A difficulty arose from the fact that mixing benzene with pure inorganic acids as a solvent generally leads to two-phase systems. In spite of this drawback, which reduces the conductivity of the system, Shepard and Dannels were able to polymerize benzene in hydrogen fluoride [99]. With the position of the Pt electrodes chosen to obtain the highest conductivity (anode in contact with the liquid-liquid interface) a dark, infusible, insoluble and insulating polymer was deposited on the anode, but its structure was not elucidated. 

Shepard, A. F., Dannels,B.F. Interfadal anodic polymers frcan benzene in hydrogene fluoride. J. Polymer Sd. A-1 4, 511 (1966). 

Example 4.6 Calculate the process jueld of benzene from toluene and benzene from hydrogen for the approximate phase split in Example 4.2. 

C, b.p. 81"C. Manufactured by the reduction of benzene with hydrogen in the presence of a nickel catalyst and recovered from natural gase.s. It is inflammable. Used as an intermediate in the preparation of nylon [6] and [66] via caprolactam and as a solvent for oils, fats and waxes, and also as a paint remover. For stereochemistry of cyclohexane see conformation. U.S. production 1980 1 megatonne. 

Some of the common aromatics found in crude oil are the simple derivatives of benzene in which one or more alkyl groups (CHg) are attached to the basic benzene molecule as a side chain which takes the place of a hydrogen atom. These arenes are either liquids or solids under standard conditions. 

The student is recommended to carry out the preparation of iodo-benzene in order to gain experience in the preparation of aqueous solutions of diazonium compounds, and then to prepare a solution of benzenediazonium hydrogen sulphate with which to carry out the chief reactions that diazonium compounds undergo. 

The tribromobenzene obtained in this way should be entirely free from unchanged tribromoaniline. To test its purity, dissolve a small quantity in hot dry benzene and pass in hydrogen chloride gas from a Kipp s apparatus no trace of crystals of tribromoaniline hydrochloride should appear. Note also that although the m.p.s of the two compounds are almost identical, that of the recrystallised product from the above preparation is considerably depressed by admixture with tribromoaniline. 

The apparatus required is similar to that described for Diphenylmelhane (Section IV,4). Place a mixture of 200 g. (230 ml.) of dry benzene and 40 g. (26 ml.) of dry chloroform (1) in the flask, and add 35 g. of anhydrous aluminium chloride in portions of about 6 g. at intervals of 5 minutes with constant shaking. The reaction sets in upon the addition of the aluminium chloride and the liquid boils with the evolution of hydrogen chloride. Complete the reaction by refluxing for 30 minutes on a water bath. When cold, pour the contents of the flask very cautiously on to 250 g. of crushed ice and 10 ml. of concentrated hydrochloric acid. Separate the upper benzene layer, dry it with anhydrous calcium chloride or magnesium sulphate, and remove the benzene in a 100 ml. Claisen flask (see Fig. II, 13, 4) at atmospheric pressure. Distil the remaining oil under reduced pressure use the apparatus shown in Fig. 11,19, 1, and collect the fraction b.p. 190-215°/10 mm. separately. This is crude triphenylmethane and solidifies on cooling. Recrystallise it from about four times its weight of ethyl alcohol (2) the triphenylmethane separates in needles and melts at 92°. The yield is 30 g. 

Cyclohexane [110-82-7] CgH 2> is a clear, essentially water-insoluble, noncorrosive Hquid that has a pungent odor. It is easily vaporized, readily flammable, and less toxic than benzene. StmcturaHy, it is a cycloparaffin. Cyclohexane was synthesized by Baeyer in 1893 and it was discovered by Markovnikov in Caucasian petroleum fractions shordy thereafter. Its presence in United States cmde oils was estabUshed in 1931 (45). Cyclohexane was produced first by hydrogenation of benzene in 1898 (46). 

Some processes use only one reactor (57) or a combination of liquid- and vapor-phase reactors (58). The goal of these schemes is to reduce energy consumption and capital cost. Hydrogenation normally is carried out at 2—3 MPa (20—30 atm). Temperature is maintained at 300—350°C to meet a typical specification of less than 500 ppm benzene in the product at higher temperatures, thermodynamic equiUbrium shifts to favor benzene and the benzene specification is impossible to attain. Also, at higher temperatures, isomerization of cyclohexane to methylcyclopentane occurs typically there is a 200 ppm specification limit on methylcyclopentane content. 

Zirconium monochloride reacts with sodium ethoxide to form additional adducts which hydrolyze in water. The monochloride does not react with benzene in a Friedel-Crafts reaction, and does not enter into intercalation reactions similar to those of zirconium disulfide. Both monohaUdes add hydrogen reversibly up to a limiting composition of ZrXH (131). 

Benzene is hydrogenated to cyclohexane. Cyclohexane is then oxidized to cyclohexanol, cyclohexanone, or adipic acid (qv). Adipic acid is used to produce nylon. Cyclohexane manufacture was responsible for about 14% of benzene consumption in 1988. 

Hydroquinine (Dihydroquinine), C20H26O2N2.2H2O. This base was isolated by Hesse from the mother liquors of quinine sulphate manufacture and is present to the extent of 5 to 6 per cent, in commercial sulphate of quinine, from which it is best isolated by the mercuric acetate process. The demand for hydroquinine as such and as a material for the preparation of hydrocupreine has led to its manufacture from quinine by catalytic hydrogenation. It crystallises from ether or benzene in needles, m.p. 173 5° (dry), — 235 7° (c = M/40, N/10 H2SO4) or... 

Stability toward reduction makes hydrogen fluoride a good medium for different hydrogenation processes [1, 2] It is a useful solvent for the hydrogenation of benzene in the presence of Lewis acids [f ] Anhydrous hydrofluonc acid has pronounced catalytic effect on the hydrogenations of various aromatic compounds, aliphatic ketones, acids, esters, and anhydrides in the presence of platinum dioxide [2] (equations 1-3)... 

In media such as water and alcohols, fluoride ion is strongly solvated by hydrogen bonding and is neither very basic nor very nucleophilic. On the other hand, the poorly solvated, or naked, fluoride ions that aie present when potassium fluoride dissolves in benzene in the presence of a crown ether aie better able to express their anionic reactivity. Thus, alkyl halides react with potassium fluoride in benzene containing 18-crown-6, thereby providing a method for the preparation of otherwise difficultly accessible alkyl fluorides. 

Isoindoles which have a free hlH group can undergo himolecular, oxidative coupling. Thus, 1-phenylisoindole (38), when refluxed in benzene in the presence of air, gives a 4,5% yield of the dehydrobisiso-indolenine (39), a product identical with that obtained by catalytic hydrogenation of o-cyanobenzophenone (37). ... 

A mixture of 2.0 g (0.064 mol) of 2-fluoromethyl-3-(o-tolyl)-6-nitro-4(3H)-qulnazolinone, Oi g of 5% palladium-carbon and 100 ml of acetic acid is shaken for 30 minutes in hydrogen gas. The initial pressure of hydrogen gas is adjusted to 46 lb and the mixture is heated with an infrared lamp during the reaction. After 30 minutes of this reaction, the pressure of hydrogen gas decreases to 6 lb. After the mixture is cooled, the mixture is filtered to remove the catalyst. The filtrate is evaporated to remove acetic acid, and the residue is dissolved in chloroform. The chloroform solution is washed with 5% aqueous sodium hydroxide and water, successively. Then, the solution is dried and evaporated to remove solvent. The oily residue thus obtained is dissolved in 2 ml of chloroform, and the chloroform solution is passed through a column of 200 g of silica gel. The silica gel column is eluted with ethyl acetate-benzene (1 1). Then, the eluate is evaporated to remove solvent. The crude crystal obtained is washed with isopropylether and recrystallized from isopropanol. 0.95 g of 2-fluoromethyl-3-(o-tolyl)-6-amino-4(3H)-quinazolinone Is obtained. Yield 52.5% MP 195°-196°C. 

When the uptake of hydrogen ceased, the catalyst was filtered and the solution was evaporated to dryness under vacuum. The residue was dissolved in a mixture of benzene-hexane, transferred to a chromatographic column with neutral alumina and the product was eluted with mixtures of benzene-hexane, gradually increasing the proportion of benzene in the mixture. Crystallization of the eluates from acetone-hexane yielded the propionate of 2a-methyldihydrotestosterone. 

The 4-hydroxy-2-methylindole (MP 112°C to 115°C from benzene/ethyl acetate), used as starting material, may be obtained by hydrogenation of 4-banzyloxy-2-dimethylamino-methylindole (MP 117°C to 120°C from benzene) in the presence of a palladium catalyst (5% on aluminum oxide). 

The benzene content of FCC gasoline is typically in the range of 0.6 vol /i to 1.3 vol%. CAAA s Simple Model requires RFC to have a maximum of 1 vol% benzene. In California, the basic requirement is also 1 vol% however, if refiners are to comply with averaging provisions, the maximum is 0.8 vol%. Operationally, the benzene content of FCC gasoline can be reduced by reducing catalyst-oil contact time and catalyst-to-oil ratio. Lower reactor temperature, lower rates of hydrogen transfer, and an octane catalyst will also reduce benzene levels. 

The most common reaction of aromatic compounds is electrophilic aromatic substitution. That is, an electrophile reacts with an aromatic ring and substitutes for one of the hydrogens. The reaction is characteristic of all aromatic rings, not just benzene and substituted benzenes. In fact, the ability of a compound to undergo electrophilic substitution is a good test of aromaticity- . 

Addition of benzoyl chloride to 2.5-dimethyl-3,4,6-triphenyl-3//-azepine (13) in benzene in the presence of 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU) leads to elimination of hydrogen chloride and formation of the 2-methylene-l//-azcpine 14.117 All attempts to isomerize the methylene derivative to 1-benzoyl-2,5-dimethyl-3,4,6-triphenyl-l//-azepine under basic conditions failed. Analogous reactions can occur with 2,5-dielhyl-3,4,6-triphenyl-3//-azepine. 

---