APT

The density of dislocations is usually stated in terms of the number of dislocation lines intersecting unit area in the crystal it ranges from 10 cm for good crystals to 10 cm" in cold-worked metals. Thus, dislocations are separated by 10 -10 A, or every crystal grain larger than about 100 A will have dislocations on its surface one surface atom in a thousand is apt to be near a dislocation. By elastic theory, the increased potential energy of the lattice near... 

Process 2, the adsorption of the reactant(s), is often quite rapid for nonporous adsorbents, but not necessarily so it appears to be the rate-limiting step for the water-gas reaction, CO + HjO = CO2 + H2, on Cu(lll) [200]. On the other hand, process 4, the desorption of products, must always be activated at least by Q, the heat of adsorption, and is much more apt to be slow. In fact, because of this expectation, certain seemingly paradoxical situations have arisen. For example, the catalyzed exchange between hydrogen and deuterium on metal surfaces may be quite rapid at temperatures well below room temperature and under circumstances such that the rate of desorption of the product HD appeared to be so slow that the observed reaction should not have been able to occur To be more specific, the originally proposed mechanism, due to Bonhoeffer and Farkas [201], was that of Eq. XVIII-32. That is. 

Cookies are different for each run. They make it easier for us to distinguish between different runs on the same or similar input files. Some are apt and humorous. They can lighten a long day s work. 

Most higher alcohols of commercial importance are primary alcohols secondary alcohols have more limited specialty uses. Detergent range alcohols are apt to be straight chain materials and are made either from natural fats and oils or by petrochemical processes. The plasticizer range alcohols are more likely to be branched chain materials and are made primarily by petrochemical processes. Whereas alcohols made from natural fats and oils are always linear, some petrochemical processes produce linear alcohols and others do not. Industrial manufacturing processes are discussed in Synthetic processes. 

The rolling operations that foUow take place first on hot (95°C) differential-speed roUs which dry and coUoid the paste and convert it iato sheet form, and then on even-speed roUs which produce smoothly surfaced propellant sheets ia which all iagredients have been uniformly iacorporated. The roU gap ia the differeatial roUs is adjustable to produce sheets of various thicknesses, and rolling is continued until the moisture is reduced to a predetermined level, usually less than 0.5%. The sheet is then cut off the roU. Differential rolling is potentially hazardous, and fires are not uncommon, although detonations are not apt to occur. Operations are conducted by remote control. 

R. A. McKay,M Study of Selected Parameters in S olid Propellant Processing,]et Propulsion Lab, Pasadena, Calif., Aug. 1986 J. L. Brown and co-workers. Manufacturing Technologyfor SolidPropellantIngredients/Preparation Reclamation, Morton Thiokol, Inc., Brigham City, Utah, Apt. 1985 W. P. Sampson, Eow Cost Continuous Processing of Solid Rocket Propellant, Al-TR-90-008, Astronautics Laboiatoiy/TSTR, Edwards AEB, Oct. 1990. 

A. N. Gent and A. G. Thomas, paper presented at Prox. 7thA.nn. Tech. Conf, CeUular Plastics Div., SPI, New York, Apt. 1963. 

Table 8 summarizes specifications for anhydrous grades of hydrazine. Propellant grades meet all requirements of the most recent Mditary Specification MIL-P-26536 D. Mditary specifications coveting the other propellant hydrazines ate MMH (Md-P-27404B, May 22, 1979) UDMH (Md-P-25604D, Amendment 1, Apt. 10,1978, Supplemental Data Sheet, Jan. 24, 1984) Aetozine-50 (Md-P-27402B, May 27,1969) H-70 (Md-P-87930, USAF, Oct. 25, 1977). 

---