Apparatus simple electrical

Several forms of apparatus employing electrical heati iig wi 11 be described. A simple form may be readily constructed from a domestic electric iron of 400-500 watts rating. The handle is removed, and two holes of 8 mm. diameter are drilled through the base (ca. 11 mm. thick) so that they meet in the centre of the block. One hole is for a 360° thermometer (small bulb) the other hole is spare and can be used for comparison with a standard thermometer. The heater is mounted on a sheet of thick asbestos board which is fixed to an appropriate wooden base. The wires from the heating unit are connected to two insulated terminals fitted on the board (Fig. 11, 11, 1). The rate of heating is controlled by either of the following methods ... 

The interaction of matter with electric or magnetic fields is widely applied for determining chemical composition. The mass spectrometer, for example, which uses a combination of electric and magnetic fields to sort out constituent ions in a sample, takes full advantage of this interaction. A simple electric-conductivity apparatus determines ions in solution as the result of applying an electric potential difference across an electrolyte... 

The so-called simple electrical apparatus plays a special part. It is defined as... 

The complete assembly for carrying out the catalytic decomposition of acids into ketones is shown in Fig. Ill, 72, 1. The main part of the apparatus consists of a device for dropping the acid at constant rate into a combustion tube containing the catalyst (manganous oxide deposited upon pumice) and heated electrically to about 350° the reaction products are condensed by a double surface condenser and coUected in a flask (which may be cooled in ice, if necessary) a glass bubbler at the end of the apparatus indicates the rate of decomposition (evolution of carbon dioxide). The furnace may be a commercial cylindrical furnace, about 70 cm. in length, but it is excellent practice, and certainly very much cheaper, to construct it from simple materials. 

Many operations involving solutions of reagents require the thorough mixing of two or more reactants, and apparatus suitable for this purpose ranges from a simple glass stirring rod to electrically operated stirrers. 

It is clear that the illustrated flowsheet is quite flexible. As shown, pulses can be produced by a 6-way valve. The valves are electrically actuated so a cycled feed can easily be produced. A separate mixture preparation apparatus has been built, so that preparing the various mixtures needed is quick and simple. 

A well-known fact of fundamental solution science is that the presence of ions in any solution gives the solution a low electrical resistance and the ability to conduct an electrical current. The absence of ions means that the solution would not be conductive. Thus, solutions of ionic compounds and acids, especially strong acids, have a low electrical resistance and are conductive. This means that if a pair of conductive surfaces are immersed into the solution and connected to an electrical power source, such as a simple battery, a current can be detected flowing in the circuit. Alternatively, if the resistance of the solution between the electrodes were measured (with an ohmmeter), it would be low. Conductivity cells based on this simple design are in common use in nonchromatography applications to determine the quality of deionized water, for example. Deionized water should have no ions dissolved in it and thus should have a very low conductivity. The conductivity detector is based on this simple apparatus. 

In such cases where even slow linear heating is too fast, stepwise isothermal heating is recommended (Fig. 14 C). Some apparatus have a built-in device or, alternatively, the realization is very simple made possible with two electrical switch clocks (see Sect. 4.1). 

Five biomass samples (hazelnut shell, cotton cocoon shell, tea factory waste, olive husk and sprace wood) were pyrolyzed in a laboratory-scale apparatus designed for the purpose of pyrolysis (Demirbas, 2001, 2002a). Figure 6.4 shows the simple experimental setup of pyrolysis. The main element of the experimental device is a vertical cylindrical reactor of stainless steel, 127.0 nun in height, 17.0 nun iimer diameter and 25.0 mm outer diameter inserted vertically into an electrically heated tubular furnace and provided with an electrical heating system power source, with a heating rate of about 5 K/s. The biomass samples ground... 

A simple electrochemical cell can be made from two test tubes connected with a third tube (the crossbar of the H ), as shown in Figure 12-1. The hollow apparatus is filled by simultaneously pouring different solutions into the two test tubes, an aqueous solution (aq) of zinc sulfate into the left tube and a copper sulfate solution into the one on the right. Then a strip of zinc metal is dipped into the ZnS04 solution, a piece of copper is inserted into the CUSO4 solution, and the two ends of the metal strips are connected by wires to an voltmeter. The lateral connecting tube allows ionic migration necessary for a closed electrical circuit. The voltmeter will show the electrical potential of 1.10 volts, which leads to the movement of electrons in the wire from the zinc electrode toward the copper electrode. 

The determination of arsenic by atomic absorption spectrometry with thermal atomisation and with hydride generation using sodium borohydride has been described by Thompson and Thomerson [29], and it was evident that this method couldbe modified for the analysis of soil. Thompson and Thoresby [30] have described a method for the determination of arsenic in soil by hydride generation and atomic absorption spectrophotometry using electrothermal atomisation. Soils are decomposed by leaching with a mixture of nitric and sulfuric acids or fusion with pyrosulfate. The resultant acidic sample solution is made to react with sodium borohydride, and the liberated arsenic hydride is swept into an electrically heated tube mounted on the optical axis of a simple, lab oratory-constructed absorption apparatus. 

Plasma polymerization of films was first used to form electrical insulation and protective coatings, but a number of workers have also prepared selective membranes by this method [60-63], A simple plasma polymerization apparatus is... 

---