Anodic condition

The outstanding characteristics of the noble metals are their exceptional resistance to corrosive attack by a wide range of liquid and gaseous substances, and their stability at high temperatures under conditions where base metals would be rapidly oxidised. This resistance to chemical and oxidative attack arises principally from the Inherently high thermodynamic stability of the noble metals, but in aqueous media under oxidising or anodic conditions a very thin film of adsorbed oxygen or oxide may be formed which can contribute to their corrosion resistance. An exception to this rule, however, is the passivation of silver and silver alloys in hydrochloric or hydrobromic acids by the formation of relatively thick halide films. 

What are the kinetics of anion incorporation into the growing oxide and how is this process influenced by anodization conditions ... 

Electronic conduction plays a limited role, if any, in anodic oxide formation, since under the anodization conditions and with a high... 

Spectroscopic ellipsometry is a non-destructive, interface sensitive, in situ technique for interface characterization. Time resolved ellipsometric spectroscopy was used to determine the mechanism of electrochemical deposition of photoresists on copper electrodes under potentiostatic, anodic conditions. Nucleation of photoresist deposition occurs randomly. During the early stages of nucleation the semi-spherical particles are separated by about 100 A. The deposits tend to grow like "pillars" up to 50 A. Further growth of the "pillars" lead to coalescence of the photopolymer deposits. 

Zha S, Tsang P, Cheng Z, and Liu M. Electrical Properties and Sulfur Tolerance of La075Sr025Cr1.xMnxO3 under Anodic Conditions. J Solid State Chem 2005 178 1844-185o ... 

Although surface defect sites are involved in the initiation of pores they do not determine the density and dimension of the pores in the bulk PS. The bulk morphology of PS is determined by the property of semiconductors and anodization conditions. However, under certain conditions, such as using surface patterning to generate initiation sites, the bulk PS morphology can be controlled to some extent. 

Somewhat surprisingly, no spin adduct was seen from the oxidation of Ph4B ( pa = 0.92 V) under similar conditions, the anode potential being varied between 0.5 and 2.2 V. Since Ph-PBN could be independently formed in a thermal reaction and was stable under the anodic conditions used, and Ph was judged to be electroinactive, it was concluded that Ph4B decomposed intramolecularly with direct formation of biphenyl. 

A sufficiently anodic bias and the availability of holes are the two necessary conditions for the dissolution of silicon aqueous HF. In this case the Si dissolution rate is proportional to the current density divided by the dissolution valence. In all other cases silicon is passivated in HF this is the case under OCP, or under cathodic conditions, or under anodic conditions if the sample is moderately n-type doped and kept in the dark. If an oxidizing agent like HN03 is added silicon will already dissolve at OCP, but the dissolution rate remains bias dependent. If an anodic bias is applied the dissolution rate will be enhanced, whereas a cathodic bias effectively decreases the rate of dissolution. 

Under anodic conditions hole transfer to HF electrolytes is accompanied by electron injection that may lead to quantum efficiencies greater than 1. This effect is known as current multiplication and is discussed in Section 4.4. 

The growth rates of anodic oxides depend on electrolyte composition and anodization conditions. The oxide thickness is reported to increase linearly with the applied bias at a rate of 0.5-0.6 nm V-1 for current densities in excess of 1 mA cnT2 and ethylene glycol-based electrolytes of a low water content [Da2, Ja2, Crl, Mel2] (for D in nm and V in V) ... 

Pore formation is a common feature of many metal and semiconductor electrodes under anodic conditions in various electrolytes. Common products, for example aluminum capacitors, have been manufactured for decades using electrochemical pore formation techniques. Nevertheless in many cases the physics of pore initiation and propagation is poorly understood. 

The oxidation of 3,6-dehydrohomoadamantane (52) with NO+BF4, photo-excited tetracyanobenzene, and under anodic conditions has been found to involve a common radical cation intermediate. The study has shown that the activation of propellane cTc-c bonds with strong oxidizing electrophiles occurs by a sequence of single-electron transfer steps. These findings are supported by ab initio computations showing that the isomeric radical cations can equilibrate with low barriers and lead to a common product. ... 

The SPE technology solves some problems but it poses others. In particular, the strong acid environment developed on the membrane calls for a complete change of electrode materials from those used in the conventional alkaline electrolysis. More specifically, especially the requirements for electrode materials for O2 evolution are stringent since the anodic conditions are especially aggressive for corrosion problems. 

Table 5.3 Electrolyte pit and composition, anodization conditions, and size of the resulting nanotubcs.

Fig. 5.8 Lateral view of the nanotubes formed in different pH solutions (pH>l). Variation of pore size with anodization potential for pH 2.8 is shown in the inset (samples 10 to 12). The anodization conditions, or each sample, are listed in Table 5.3.

Since most metals are oxidized under anodic conditions, practically useful anode materials have to be looked for among the noble metals. Platinum (also in... 

Figure 23 Schematic polarization curve for metal that spontaneously passivates but pits upon anodic polarization. A hysteresis loop, which can appear during a reverse scan, is shown ending at Erp. One dotted line shows behavior for anodizing conditions, while the other shows transpassive dissolution.

---