Anionic polymerization solvent effects

Anionic polymerization of vinyl monomers can be effected with a variety of organometaUic compounds alkyllithium compounds are the most useful class (1,33—35). A variety of simple alkyllithium compounds are available commercially. Most simple alkyllithium compounds are soluble in hydrocarbon solvents such as hexane and cyclohexane and they can be prepared by reaction of the corresponding alkyl chlorides with lithium metal. Methyllithium [917-54-4] and phenyllithium [591-51-5] are available in diethyl ether and cyclohexane—ether solutions, respectively, because they are not soluble in hydrocarbon solvents vinyllithium [917-57-7] and allyllithium [3052-45-7] are also insoluble in hydrocarbon solutions and can only be prepared in ether solutions (38,39). Hydrocarbon-soluble alkyllithium initiators are used directiy to initiate polymerization of styrene and diene monomers quantitatively one unique aspect of hthium-based initiators in hydrocarbon solution is that elastomeric polydienes with high 1,4-microstmcture are obtained (1,24,33—37). Certain alkyllithium compounds can be purified by recrystallization (ethyllithium), sublimation (ethyllithium, /-butyUithium [594-19-4] isopropyllithium [2417-93-8] or distillation (j -butyUithium) (40,41). Unfortunately, / -butyUithium is noncrystaUine and too high boiling to be purified by distiUation (38). Since methyllithium and phenyllithium are crystalline soUds which are insoluble in hydrocarbon solution, they can be precipitated into these solutions and then redissolved in appropriate polar solvents (42,43). OrganometaUic compounds of other alkaU metals are insoluble in hydrocarbon solution and possess negligible vapor pressures as expected for salt-like compounds. 

The solvent used in the anionic polymerization of 1,4-DVB by n-BuLi also has an important effect on the polymer structure. If polymerization reactions are carried out in benzene/THF mixtures, the onset of macrogelation can be retarded by increasing the THF fraction in the solvent mixture [230]. Hexane, that is a solvent for the monomer but a precipitant for the resulting polymer, was not suitable because an insoluble aggregate was formed within a few minutes [230]. For hexane /THF mixtures with equal volumes, the conditions for the synthesis of a soluble polymer depends on the concentrations of 1,4-DVB and n-BuLi (Fig. 50). The course of the curve in the transition region from a soluble polymer to a macrogel is similar to that shown in Fig. 48 for n-BuLi/THF. 

The propagation rate constant and the polymerization rate for anionic polymerization are dramatically affected by the nature of both the solvent and the counterion. Thus the data in Table 5-10 show the pronounced effect of solvent in the polymerization of styrene by sodium naphthalene (3 x 1CT3 M) at 25°C. The apparent propagation rate constant is increased by 2 and 3 orders of magnitude in tetrahydrofuran and 1,2-dimethoxyethane, respectively, compared to the rate constants in benzene and dioxane. The polymerization is much faster in the more polar solvents. That the dielectric constant is not a quantitative measure of solvating power is shown by the higher rate in 1,2-dimethoxyethane (DME) compared to tetrahydrofuran (THF). The faster rate in DME may be due to a specific solvation effect arising from the presence of two ether functions in the same molecule. 

For any specific type of initiation (i.e., radical, cationic, or anionic) the monomer reactivity ratios and therefore the copolymer composition equation are independent of many reaction parameters. Since termination and initiation rate constants are not involved, the copolymer composition is independent of differences in the rates of initiation and termination or of the absence or presence of inhibitors or chain-transfer agents. Under a wide range of conditions the copolymer composition is independent of the degree of polymerization. The only limitation on this generalization is that the copolymer be a high polymer. Further, the particular initiation system used in a radical copolymerization has no effect on copolymer composition. The same copolymer composition is obtained irrespective of whether initiation occurs by the thermal homolysis of initiators such as AIBN or peroxides, redox, photolysis, or radiolysis. Solvent effects on copolymer composition are found in some radical copolymerizations (Sec. 6-3a). Ionic copolymerizations usually show significant effects of solvent as well as counterion on copolymer composition (Sec. 6-4). 

Copolymerizations of nonpolar monomers with polar monomers such as methyl methacrylate and acrylonitrile are especially comphcated. The effects of solvent and counterion may be unimportant compared to the side reactions characteristic of anionic polymerization of polar monomers (Sec. 5-3b-4). In addition, copolymerization is often hindered by the very low tendency of one of the cross-propagation reactions. For example, polystyryl anions easily add methyl methacrylate but there is little tendency for poly(methyl methacrylate) anions to add styrene. Many reports of styrene-methyl methacrylate (and similar comonomer pairs) copolymerizations are not copolymerizations in the sense discussed in this chapter. 

The anionic polymerization of 1,3-dienes yields different polymer structures depending on whether the propagating center is free or coordinated to a counterion [Morton, 1983 Quirk, 2002 Senyek, 1987 Tate and Bethea, 1985 Van Beylen et al., 1988 Young et al., 1984] Table 8-9 shows typical data for 1,3-butadiene and isoprene polymerizations. Polymerization of 1,3-butadiene in polar solvents, proceeding via the free anion and/or solvent-separated ion pair, favors 1,2-polymerization over 1,4-polymerization. The anionic center at carbon 2 is not extensively delocalized onto carbon 4 since the double bond is not a strong electron acceptor. The same trend is seen for isoprene, except that 3,4-polymerization occurs instead of 1,2-polymerization. The 3,4-double bond is sterically more accessible and has a lower electron density relative to the 1,2-double bond. Polymerization in nonpolar solvents takes place with an increased tendency toward 1,4-polymerization. The effect is most pronounced with... 

TABLE 8-9 Effect of Solvent and Counterion on Stereochemistry in Anionic Polymerization of 1,3-Dienes"... 

The stereoselective polymerization of various acrylates and methacrylates has been studied using initiators such as atkyllithium [Bywater, 1989 Pasquon et al., 1989 Quirk, 1995, 2002]. Table 8-12 illustrates the effects of counterion, solvent, and temperature on the stereochemistry of the anionic polymerization of methyl methacrylate (MMA). In polar solvents (pyridine and THF versus toluene), the counterion is removed from the vicinity of the propagating center and does not exert an influence on entry of the next monomer unit. The tendency is toward syndiotactic placement via chain end control. The extent of syndiotacticity... 

For some monomers (e.g., nitroethylene and 2-cyano-2,4-hexadienoic acid ester, CH3-CH=CH-CH=C(CN)-COOR), anionic polymerization can be conducted in aqueous alkaline solution. Other anionic initiators are Lewis bases, e.g., tertiary amines or phosphines, and organometallic compounds (see Sect. 3.2.1.2). Since the polarizability of unsaturated compounds depends very much on the substituents and on the solvent used, there are considerable differences in the effectiveness of the initiators mentioned. 

Anionic polymerization of vinyl monomers can be effected with a variety of organomciallic compounds alkyllithium compounds are the most useful class. A variety of simple alkyllithium compounds are available commercially. Most simple alkyllithium compounds ate soluble in hydrocarbon solvents such as hexane and cyclohexane and they can be prepared by reaction of the corresponding alkyl chlorides with lithium metal. 

C olvents have different effects on polymerization processes. In radical polymerizations, their viscosity influences the diffusion-controlled bimolecular reactions of two radicals, such as the recombination of the initiator radicals (efficiency) or the deactivation of the radical chain ends (termination reaction). These phenomena are treated in the first section. In anionic polymerization processes, the different polarities of the solvents cause a more or less strong solvation of the counter ion. Depending on this effect, the carbanion exists in three different forms with very different propagation constants. These effects are treated in the second section. The final section shows that the kinetics of the... 

The only isomer that has been studied is 4-(26). The polymerization was effected in either ammonia solvent or in a solvent-free system.57 An anionic mechanism was proposed, and molecular weights were in the range of 10,000 to 260,000. As expected, higher current densities led to lower average molecular weights. 

The solution thus consists of different particles denoted as contact ion pairs, solvent-separated ion pairs and free ions. The fraction of the individual particles depends on the type of salt, type of solvent, polymerization system, temperature, and salt concentration. The catalytic effect of these particles may be very different as is evident in anionic polymerization of vinyl monomers. For instance, free polystyryl anion is 800times more reactive than its ion pair with the sodium counterion 60 . From this fact it follows that, although the portion of free ions is small in the reaction system, they may play an important role. On the other hand, anionic polymerization and copolymerization of heterocycles proceeds mostly via ion pairs. This is due to a strong localization of the negative charge on the chain-end heteroatom which strongly stabilizes the ion pair itself62. Ionic dissociation constants and ion contributions to the reaction kinetics are usually low. This means that for heterocycles the difference between the catalytic effect of ion pairs and free ions is much weaker than for the polymerization of unsaturated compounds. This is well documented by the copolymerization of anhydrides with epoxides where the substi-... 

Anionic ring-opening polymerization of l,2,3,4-tetramethyl-l,2,3,4-tetraphenylcyclo-tetrasilane is quite effectively initiated by butyllithium or silyl potassium initiators. The process resembles the anionic polymerization of other monomers where solvent effects play an important role. In THF, the reaction takes place very rapidly but mainly cyclic live- and six-membered oligomers are formed. Polymerization is very slow in nonpolar media (toluene, benzene) however, reactions are accelerated by the addition of small amounts of THF or crown ethers. The stereochemical control leading to the formation of syndiotactic, heterotactic or isotactic polymers is poor in all cases. In order to improve the stereoselectivity of the polymerization reaction, more sluggish initiators like silyl cuprates are very effective. A possible reaction mechanism is discussed elsewhere49,52. 

The elementary reactions of carbocationic polymerizations can be separated into three types. Deactivation of carbenium ions with anions and transfer to counteranion are ion-ion reactions, propagation and transfer to monomer are ion-dipole reactions, and ionization is a dipole-dipole reaction [274]. Ion-ion and dipole-dipole reactions with polar transition states experience the strongest solvent effects. Carbocationic propagation is an ion-dipole reaction in which a growing carbenium ion adds electro-philically to an alkene it should be weakly accelerated in less polar solvents because the charge is more dispersed in the transition state than in the ground state [276]. However, a model addition reaction of bis(p-methoxyphenyl)carbenium ions to 2-methyl- 1-pentene is two times faster in nitroethane (e = 28) than in methylene chloride (e = 9) at - 30° C [193]. However, this is a minor effect which corresponds to only ddG = 2 kJ morit may also be influenced by specific solvation, polarizability, etc. [276,277]. 

Controlled/living systems can be usually obtained when the polymerization is sufficiently slow and when either nucleophilic anions or additives are present (Sections IV and V). This means that the proportion of carbenium ions should be low and conversion to dormant species, fast. Nevertheless, under such conditions cationic species can be detected by dynamic NMR, by ligand exchange, salt, and solvent effects, and by other methods discussed in Chapters 2, 3, and in this section. Under typical controlled/living conditions, dormant species such as onium ions and covalent esters predominate. It is possible that the active species are strongly solvated by monomer and by some additives. These interactions may lead to a stabilization of the carbocations. However, in the most general case, this stabilization has a dynamic sense and can be described by the reversible exchange between carbocations and dormant species. 

---