Alloying trends

Figure 5.19. Zr alloys. Trend of the highest melting points of the binary compounds with the different elements. Notice that the data concerning the Zr-S system are very uncertain.

L. Karlsson, L. Svensson, and H. Larsson, Characteristics of Friction Stir Welded Aluminum Alloys, Trends in Welding Research, Proc. of the Eifth Int. Conf, June 1-5, 1998 (Pine Mountain, GA), J. Vitek, S. David, J. Johnson, H. Smartt, and T. DebRoy, Ed., ASM International, Materials Park, OH, 1999, p 574-579... 

C.D. Sorensen and T.W. Nelson, Sigma Phase Formation in Friction Stirring of Iron-Nickel-Chromium Alloys, Trends in Welding Research, Proceedings of the Seventh International Conference, ASM International, 2005... 

In Chap. 4 we discussed the crystallizability of polymers and the importance of this property on the mechanical behavior of the bulk sample. Following the logic that leads to Eq. (4.17), the presence of a comonomer lowers T for a polymer. Carrying this further, we can compare a copolymer to an alloy in which each component lowers the melting point of the other until a minimummelting eutectic is produced. Similar trends exist in copolymers. 

The lead-bearing components ate released from the case and other nordead-containing parts, followed by the smelting of the battery plates, and refinement to pure lead or specification alloys. The trend toward battery grid alloys having Httle or no antimony, increases the abiHty of a recovery process to produce soft lead (refined). As requited in the production of primary lead, each step in the secondary operations must meet the environmental standards for lead concentration in ait (see Air pollution Lead compounds, industrial toxicology). 

P/M processing of titanium aluminides results in more consistent product quaHty than the conventional casting process, and offers novel alloy/microstmcture possibiHties and improved ductiHty. Processing trends include use of high (1200—1350°C) temperature sintering to improve mechanical properties of steel and stainless steel parts. 

Because zinc-based alloys have low melting points, energy savings in the melting operation are substantial and the foundry operation is essentially free of fume. With the current trend of increasing energy costs and pollution control, cost benefits can be considerable (114). 

The proper selection of the lead alloy depends on the intended use and the economics of the lead—acid battery appHcation. The metallurgical and electrochemical aspects of the lead are discussed in the Hterature in a comprehensive manner (81,85—87) as are trends of lead alloy use for manufacture of battery grids (88). 

The present trend of material seleeted for collection headers is toward Incoloy 800. The cast alloys used, HK and HT, have failed in most instances because of their inherently low ductility—especially after exposure to elevated temperature. It now appears that wrought alloys should be used in preference to cast alloys unless the higher creep strength of the east alloy is required and the inherently low ductility of the aged cast alloy is considered in the design. 

To summarize we have reproduced the intricate structural properties of the Fe-Co, Fe-Ni and the Fe-Cu alloys by means of LMTO-ASA-CPA theory. We conclude that the phase diagram of especially the Fe-Ni alloys is heavily influenced by short range order effects. The general trend of a bcc-fcc phase transition at lower Fe concentrations is in accordance with simple band Ailing effects from canonical band theory. Due to this the structural stability of the Fe-Co alloys may be understood from VGA and canonical band calculations, since the common band model is appropriate below the Fermi energy for this system. However, for the Fe-Ni and the Fe-Cu system this simple picture breaks down. 

There is an accelerating trend away from the use of lead-containing solders in contact with potable water. The effects of galvanic corrosion of one of the substitute alloys (Sn3%Ag) in contact with a number of other metals including copper have therefore been studied . The corrosion of tin/Iead alloys in different electrolytes including nitrates, nitric and acetic acids, and citric acid over the pH range 2-6 were reported. The specific alloy Pb/15%Sn was studied in contact with aqueous solutions in the pH range... 

The desire to replace cadmium is generally attributed to its toxicity, both in terms of process pollution and product corrosion, and several alternatives are feasible thicker zinc, tin-zinc alloy or tin-nickel alloy depending upon the precise application " . The demise of decorative nickel-chrome systems in the automotive industries of the world is partly due to cost and partly to market image, and not to technical performance where major improvements took place in the period 1960-1975 through the establishment of duplex nickel under-layers and micro discontinuous chromium top-layers. In the 1980s the trend has been towards black finishes produced generally by powder-applied epoxy polymers. 

The trend in architectural applications has been towards more matt finishes, and the sodium hydroxide-based etchants used frequently contain additives such as sodium nitrate or nitrite or sodium fluoride. Chelating agents such as gluconates, heptonates or sorbitol are added to complex the aluminium produced, and other additives such as sulphides may be present in the etchant to complex zinc dissolved from the alloy, and allow it to be used continuously without dumping ... 

Within the general trend in the behavior across the actinide series, their alloys, and their metallic compounds from superconductors to local moment magnets, the only serious irregularity occurs in some plutonium compounds. These compounds should be magnetic but turn out to be temperature independent paramagnets. 

The trend in CVD metallization is toward greater use of copper, and the refractory metals and their silicides in multilayered metallization designs, typically consisting of metal-silicide contacts, refractory-metal barriers, and copper or an aluminum alloy as the principal interconnect metal. Other metals deposited by CVD such as chromium, molybdenum, platinum, rhodium, and ruthenium are also actively considered for use as conductors. 

Such calculations have also been performed for isolated impurities of late transition metals alloyed into the surface of other transition metals, and the trends are the same. The accuracy of the numbers in Fig. 6.33 is limited since many approximations had to be made to calculate them. Nevertheless, they reflect trends very well and give useful insight into reactivity trends that have actually been measured for a number of pseudomorfic overlayers [J.A. Rodriquez and D.W. Goodman, Science 257 (1992) 897]. 

---