Alkylation catalysts, acidic

In the petroleum (qv) industry hydrogen bromide can serve as an alkylation catalyst. It is claimed as a catalyst in the controlled oxidation of aHphatic and ahcycHc hydrocarbons to ketones, acids, and peroxides (7,8). AppHcations of HBr with NH Br (9) or with H2S and HCl (10) as promoters for the dehydrogenation of butene to butadiene have been described, and either HBr or HCl can be used in the vapor-phase ortho methylation of phenol with methanol over alumina (11). Various patents dealing with catalytic activity of HCl also cover the use of HBr. An important reaction of HBr in organic syntheses is the replacement of aHphatic chlorine by bromine in the presence of an aluminum catalyst (12). Small quantities of hydrobromic acid are employed in analytical chemistry. 

A multitude of 1,4-dicarbonyls (1) undergo the Paal-Knorr reaction with and ranging from H to alkyl, aryl, carbonyl, nitrile, and phosphonate, while R and R vary between H, alkyl, aryl, trialkylsilyl, and O-alkyl. Protic acid catalysts are typically used with sulfuric, hydrochloric, and p-toluenesulfonic acids the most popular. Conversion to the furan takes place either at room temperature or upon heating with reaction times varying from five minutes to 24 hours and yields ranging from 17-100%. 

The methodology of a Lewis acid dissolved in an ionic liquid has been used for Friedel-Crafts alkylation reactions. Song [85] has reported that scandium(III) tri-flate in [BMIM][PFg] acts as an alkylation catalyst in the reaction between benzene and hex-l-ene (Scheme 5.1-55). 

Carboncations also form from an alkyl halide when a Lewis acid catalyst is used. Aluminum chloride is the commonly used Friedel-Crafts alkylation catalyst. Friedel-Crafts alkylation reactions have been reviewed by Roberts and Khalaf ... 

In 1950 the Fischer-Tropsch synthesis was banned in Germany by the allied forces. Sinarol, a high paraffinic kerosene fraction sold by Shell, was used as a substitute. This ban coincided with the rapid development of the European petrochemical industry, and in due time Fischer-Tropsch synthesis applied to the production of paraffins became uneconomic anyway. After the war there was a steady worldwide increase in the demand for surfactants. In order to continually meet the demand for synthetic detergents, the industry was compelled to find a substitute for /z-paraffin. This was achieved by the oligomerization of the propene part of raffinate gases with phosphoric acid catalyst at 200°C and about 20 bars pressure to produce tetrapropene. Tetrapropene was inexpensive, comprising a defined C cut and an olefinic double bond. Instead of the Lewis acid, aluminum chloride, hydrofluoric acid could now be used as a considerably milder, more economical, and easier-to-handle alkylation catalyst [4],... 

It is possible to alkylate benzoic acids directly, without the need to prepare reactive potassium salts in a separate step, because they can be generated in situ by reacting the acid with a base (potassium carbonate or hydroxide) in the presence of a phase-transfer catalyst. 

Alkylation of the 1,2,4-triazole ring by alkyl radical species has been achieved reaction of 1-methyl-1,2,-4-triazole 37 with alkyl carboxylic acids in the presence of a silver catalyst gave the corresponding 2-alkylated triazoles 38a-e in moderate yields (Equation 9 and Table 1) <2001TL7353>. 

SARP [Sulphuric acid recovery process] A method for recovering sulfuric acid which has been used for alkylation, for re-use. The acid is reacted with propylene, yielding dipropyl sulfate, which is extracted from the acid tar with isobutane. It is not necessary to hydrolyze the sulfate to sulfuric acid because the sulfate itself is an active alkylation catalyst. 

Since the discovery of alkylation, the elucidation of its mechanism has attracted great interest. The early findings are associated with Schmerling (17-19), who successfully applied a carbenium ion mechanism with a set of consecutive and simultaneous reaction steps to describe the observed reaction kinetics. Later, most of the mechanistic information about sulfuric acid-catalyzed processes was provided by Albright. Much less information is available about hydrofluoric acid as catalyst. In the following, a consolidated view of the alkylation mechanism is presented. Similarities and dissimilarities between zeolites as representatives of solid acid alkylation catalysts and HF and H2S04 as liquid catalysts are highlighted. Experimental results are compared with quantum-chemical calculations of the individual reaction steps in various media. 

With both liquid acid catalysts, but presumably to a higher degree with sulfuric acid, hydrides are not transferred exclusively to the carbenium ions from isobutane, but also from the conjunct polymers 44,46,71). Sulfuric acid containing 4-6 wt% of conjunct polymers produces a much higher quality alkylate than acids without ASOs (45). Cyclic and unsaturated compounds, which are both present in conjunct polymers, are known to be hydride donors (72). As was mentioned in Section II.B, these species can abstract a hydride from isobutane to form the -butyl cation, and they can give a hydride to a carbenium ion, producing the corresponding alkane, for example the TMPs, as shown in reactions (7) and (8). 

The lifetime of a zeolitic alkylation catalyst depends on the concentration of Brpnsted acid sites. This has been shown by Nivarthy et al. (78), who used a series of zeolites H-BEA with varied concentrations of back-exchanged sodium ions. The sodium decreased the concentration of Brpnsted acid centers, which led to a concomitant decrease in the measured catalyst lifetime during alkylation. 

A variety of solid acids besides zeolites have been tested as alkylation catalysts. Sulfated zirconia and related materials have drawn considerable attention because of what was initially thought to be their superacidic nature and their well-demonstrated ability to isomerize short linear alkanes at temperatures below 423 K. Corma et al. (188) compared sulfated zirconia and zeolite BEA at reaction temperatures of 273 and 323 K in isobutane/2-butene alkylation. While BEA catalyzed mainly dimerization at 273 K, the sulfated zirconia exhibited a high selectivity to TMPs. At 323 K, on the other hand, zeolite BEA produced more TMPs than sulfated zirconia, which under these conditions produced mainly cracked products with 65 wt% selectivity. The TMP/DMH ratio was always higher for the sulfated zirconia sample. These distinctive differences in the product distribution were attributed to the much stronger acid sites in sulfated zirconia than in zeolite BEA, but today one would question this suggestion because of evidence that the sulfated zirconia catalyst is not strongly acidic, being active for alkane isomerization because of a combination of acidic character and redox properties that help initiate hydrocarbon conversions (189). The time-on-stream behavior was more favorable for BEA, which deactivated at a lower rate than sulfated zirconia. Whether differences in the adsorption of the feed and product molecules influenced the performance was not discussed. 

Cesium salts of 12-tungstophosphoric acid have been compared to the pure acid and to a sulfated zirconia sample for isobutane/1-butene alkylation at room temperature. The salt was found to be much more active than either the acid or sulfated zirconia (201). Heteropolyacids have also been supported on sulfated zirconia catalysts. The combination was found to be superior to heteropolyacid supported on pure zirconia and on zirconia and other supports that had been treated with a variety of mineral acids (202). Solutions of heteropolyacids (containing phosphorus or silicon) in acetic acid were tested as alkylation catalysts at 323 K by Zhao et al. (203). The system was sensitive to the heteropoly acid/acetic acid ratio and the amount of crystalline water. As observed in the alkylation with conventional liquid acids, a polymer was formed, which enhanced the catalytic activity. 

Nafion-H, a perfluorinated sulfonic acid resin, is another strongly acidic solid that has been explored as alkylation catalyst. Rprvik et al. (204) examined unsupported Nafion-H with a nominal surface area of 0.2 m2/g (surface area of a swellable polymer is difficult to define) in isobutane/2-butene alkylation at 353 K and compared it with a CeY zeolite. The zeolite gave a better alkylate and higher conversion than Nafion-H, which produced significant amounts of octenes and heavy-end products. The low surface area of the resin and questions about the accessibility of the sulfonic acid groups probably make the comparison inadequate. 

The choice of appropriate reaction conditions is crucial for optimized performance in alkylation. The most important parameters are the reaction temperature, the feed alkane/alkene ratio, the alkene space velocity, the alkene feed composition, and the reactor design. Changing these parameters will induce similar effects for any alkylation catalyst, but the sensitivity to changes varies from catalyst to catalyst. Table II is a summary of the most important parameters employed in industrial operations for different acids. The values given for zeolites represent best estimates of data available from laboratory and pilot-scale experiments. 

In principle, the same rules hold true when zeolitic alkylation catalysts are used. A detailed study of the influence of PO and OSV on the performance of zeolite H-BEA in a backmix reactor was reported by de Jong et al. (80). The authors developed a simple model of the kinetics, which predicted catalyst lifetimes as a function of P/O and OSV. Catalyst lifetime (which is equivalent to the catalyst productivity, the reciprocal of acid consumption) increased with increasing P/O ratio and decreasing OSV. Furthermore, the authors persuasively demonstrated the superiority of a backmix reactor over a plug flow reactor. Qualitatively similar results were obtained by Taylor and Sherwood (222) employing a USY zeolite catalyst in a backmix reactor. The authors stressed the detrimental effect of unreacted alkene on the catalyst lifetime and product quality. Feller et al. (89) tested LaX zeolites in a backmix reactor and found the catalyst productivity to be nearly independent of the OSV within the examined OSV range. At higher values of OSV, the catalyst life was shorter, but in this shorter time the same total amount of product was produced. The P/O ratio had only a moderate influence on the catalyst performance. 

---