Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Phosphines alcohols

Other common inhibitors employed for platinum-cured siloxanes include maleates, fumarates, acetylenic alcohols, phosphines and tetramethyltetravinyltetrasiloxane (D/ ). Other key variables for platinum-cured siloxanes include The molecular weight of the vinyl-stopped polymer, M DnM the amount of Si-H in the Si-H-on-chain polymer, MD nM and the ratio of vinyl to Si-H the amount of filler and degree of surface treatment, the amount of platinum catalyst and the amount and type of inhibitor. [Pg.18]

It is well known that in esterifications of phosphinic acids, it does not normally react with alcohols under thermal conditions, but in the presence of microwave exposure, the esterifications took place, which shows the importance of microwaves. It was observed that maximum 12-15% conversions were attained on traditional heating. It was found that due to the consequence of the hydrophobic medium established by the long chain alcohol/phosphinic ester, microwave-assisted esterifica-hons were not reversible. The potential of the microwave technique in the synthesis of phosphinates can be understood on the basis of the energetics of the esterification of phosphinic acids under microwave conditions. A series of new cychc phosphinates with lipophilic alkyl groups was synthesized by Keglevich et al. (2012). [Pg.348]

To a mixture of 100 ml of dry dichloromethane, 0.10 mol of propargyl alcohol and 0.11 mol of triethylamine was added a solution of 0.05 mol of Ph2PCl in 75 ml of dichloromethane in 3 min between -80 and -90°C. The cooling bath was removed, and when the temperature had reached 10°C, the reaction mixture was poured into a solution of 2.5 ml of 362 HCl in 100 ml of water. After vigorous shaking the lower layer was separated and the aqueous layer was extracted twice with 25-ml portions of dichloromethane. The combined solutions were washed twice with water, dried over magnesium sulfate and then concentrated in a water-pump vacuum, giving almost pure allenyl phosphine oxide as a white solid, m.p. 98-100 5, in almost 1002 yield. [Pg.199]

Butynediol is more difficult to polymerize than propargyl alcohol, but it cyclotrimerizes to hexamethylolbenzene [2715-91 -5] (benzenehexamethanol) with a nickel carbonyl—phosphine catalyst (64) with a rhodium chloride—arsine catalyst a yield of 70% is claimed (65). [Pg.106]

Many of these reactions are reversible, and for the stronger nucleophiles they usually proceed the fastest. Typical examples are the addition of ammonia, amines, phosphines, and bisulfite. Alkaline conditions permit the addition of mercaptans, sulfides, ketones, nitroalkanes, and alcohols to acrylamide. Good examples of alcohol reactions are those involving polymeric alcohols such as poly(vinyl alcohol), cellulose, and starch. The alkaline conditions employed with these reactions result in partial hydrolysis of the amide, yielding mixed carbamojdethyl and carboxyethyl products. [Pg.133]

The reaction with sodium sulfite or bisulfite (5,11) to yield sodium-P-sulfopropionamide [19298-89-6] (C3H7N04S-Na) is very useful since it can be used as a scavenger for acrylamide monomer. The reaction proceeds very rapidly even at room temperature, and the product has low toxicity. Reactions with phosphines and phosphine oxides have been studied (12), and the products are potentially useful because of thek fire retardant properties. Reactions with sulfide and dithiocarbamates proceed readily but have no appHcations (5). However, the reaction with mercaptide ions has been used for analytical purposes (13)). Water reacts with the amide group (5) to form hydrolysis products, and other hydroxy compounds, such as alcohols and phenols, react readily to form ether compounds. Primary aUphatic alcohols are the most reactive and the reactions are compHcated by partial hydrolysis of the amide groups by any water present. [Pg.133]

Aqueous mineral acids react with BF to yield the hydrates of BF or the hydroxyfluoroboric acids, fluoroboric acid, or boric acid. Solution in aqueous alkali gives the soluble salts of the hydroxyfluoroboric acids, fluoroboric acids, or boric acid. Boron trifluoride, slightly soluble in many organic solvents including saturated hydrocarbons (qv), halogenated hydrocarbons, and aromatic compounds, easily polymerizes unsaturated compounds such as butylenes (qv), styrene (qv), or vinyl esters, as well as easily cleaved cycHc molecules such as tetrahydrofuran (see Furan derivatives). Other molecules containing electron-donating atoms such as O, S, N, P, etc, eg, alcohols, acids, amines, phosphines, and ethers, may dissolve BF to produce soluble adducts. [Pg.160]

In general, peroxomonosulfates have fewer uses in organic chemistry than peroxodisulfates. However, the triple salt is used for oxidizing ketones (qv) to dioxiranes (7) (71,72), which in turn are useful oxidants in organic chemistry. Acetone in water is oxidized by triple salt to dimethyldioxirane, which in turn oxidizes alkenes to epoxides, polycycHc aromatic hydrocarbons to oxides and diones, amines to nitro compounds, sulfides to sulfoxides, phosphines to phosphine oxides, and alkanes to alcohols or carbonyl compounds. [Pg.95]

In the alkaline process, an aqueous solution of sodium hydroxide is allowed to react with molten, yellow phosphoms. A long-chain alcohol is used as a dispersant (3). The reaction to produce phosphine may be represented by equation 1. [Pg.317]

Homogeneous rhodium-catalyzed hydroformylation (135,136) of propene to -butyraldehyde (qv) was commercialized in 1976. -Butyraldehyde is a key intermediate in the synthesis of 2-ethyIhexanol, an important plasticizer alcohol. Hydroformylation is carried out at <2 MPa (<290 psi) at 100°C. A large excess of triphenyl phosphine contributes to catalyst life and high selectivity for -butyraldehyde (>10 1) yielding few side products (137). Normally, product separation from the catalyst [Rh(P(C2H2)3)3(CO)H] [17185-29-4] is achieved by distillation. [Pg.180]

Conventional triorganophosphite ligands, such as triphenylphosphite, form highly active hydroformylation catalysts (95—99) however, they suffer from poor durabiUty because of decomposition. Diorganophosphite-modified rhodium catalysts (94,100,101), have overcome this stabiUty deficiency and provide a low pressure, rhodium catalyzed process for the hydroformylation of low reactivity olefins, thus making lower cost amyl alcohols from butenes readily accessible. The new diorganophosphite-modified rhodium catalysts increase hydroformylation rates by more than 100 times and provide selectivities not available with standard phosphine catalysts. For example, hydroformylation of 2-butene with l,l -biphenyl-2,2 -diyl... [Pg.374]

R SiH and CH2= CHR interact with both PtL and PtL 1. Complexing or chelating ligands such as phosphines and sulfur complexes are exceUent inhibitors, but often form such stable complexes that they act as poisons and prevent cute even at elevated temperatures. Unsaturated organic compounds are preferred, such as acetylenic alcohols, acetylene dicarboxylates, maleates, fumarates, eneynes, and azo compounds (178—189). An alternative concept has been the encapsulation of the platinum catalysts with either cyclodextrin or in thermoplastics or siUcones (190—192). [Pg.48]

Use of alcohol as a solvent for carbonylation with reduced Pd catalysts gives vinyl esters. A variety of acrylamides can be made through oxidative addition of carbon monoxide [630-08-0] CO, and various amines to vinyl chloride in the presence of phosphine complexes of Pd or other precious metals as catalyst (14). [Pg.414]

Primary Amyl Alcohols. Primary amyl alcohols (qv) are manufactured by hydroformylation of mixed butenes, followed by dehydrogenation (114). Both 1-butene and 2-butene yield the same product though in slightly different ratios depending on the catalyst and conditions. Some catalyst and conditions produce the alcohols in a single step. By modifying the catalyst, typically a cobalt carbonyl, with phosphoms derivatives, such as tri( -butyl)phosphine, the linear alcohol can be the principal product from 1-butene. [Pg.372]

The hydroformylation reaction is carried out in the Hquid phase using a metal carbonyl catalyst such as HCo(CO)4 (36), HCo(CO)2[P( -C4H2)] (37), or HRh(CO)2[P(CgH3)2]2 (38,39). The phosphine-substituted rhodium compound is the catalyst of choice for new commercial plants that can operate at 353—383 K and 0.7—2 MPa (7—20 atm) (39). The differences among the catalysts are found in their intrinsic activity, their selectivity to straight-chain product, their abiHty to isomerize the olefin feedstock and hydrogenate the product aldehyde to alcohol, and the ease with which they are separated from the reaction medium (36). [Pg.51]

CP can also be prepared by the reaction of cellulose with phosphoms oxychloride in pyridine (37) or ether in the presence of sodium hydroxide (38). For the most part these methods yield insoluble, cross-linked, CP with a low DS. A newer method based on reaction of cellulose with molten urea—H PO is claimed to give water soluble CP (39). The action of H PO and P2 5 cellulose in an alcohol diluent gives a stable, water-soluble CP with a high DS (>5% P) (40). These esters are dame resistant and have viscosities up to 6000 mPa-s(=cP) in 5 wt % solution. Cellulose dissolved in mixtures of DMF—N2O4 can be treated with PCl to give cellulose phosphite [37264-91-8] (41) containing 11.5% P and only 0.8% Cl. Cellulose phosphinate [67357-37-5] and cellulose phosphonate [37264-91 -8] h.a.ve been prepared (42). [Pg.265]

Examples are given of common operations such as absorption of ammonia to make fertihzers and of carbon dioxide to make soda ash. Also of recoveiy of phosphine from offgases of phosphorous plants recoveiy of HE oxidation, halogenation, and hydrogenation of various organics hydration of olefins to alcohols oxo reaction for higher aldehydes and alcohols ozonolysis of oleic acid absorption of carbon monoxide to make sodium formate alkylation of acetic acid with isobutylene to make teti-h ty acetate, absorption of olefins to make various products HCl and HBr plus higher alcohols to make alkyl hahdes and so on. [Pg.2110]

Synthesis of azindines Irom epoxides via amino alcohols or azido alcohols and reaction with phosphines or phosphites... [Pg.38]


See other pages where Phosphines alcohols is mentioned: [Pg.337]    [Pg.307]    [Pg.234]    [Pg.456]    [Pg.1920]    [Pg.234]    [Pg.31]    [Pg.337]    [Pg.307]    [Pg.234]    [Pg.456]    [Pg.1920]    [Pg.234]    [Pg.31]    [Pg.293]    [Pg.276]    [Pg.160]    [Pg.282]    [Pg.2]    [Pg.142]    [Pg.198]    [Pg.263]    [Pg.456]    [Pg.468]    [Pg.511]    [Pg.517]    [Pg.134]    [Pg.103]    [Pg.112]    [Pg.380]    [Pg.73]    [Pg.73]    [Pg.286]    [Pg.27]    [Pg.435]    [Pg.378]    [Pg.171]    [Pg.50]   
See also in sourсe #XX -- [ Pg.71 ]

See also in sourсe #XX -- [ Pg.246 ]

See also in sourсe #XX -- [ Pg.28 , Pg.246 ]




SEARCH



© 2024 chempedia.info