Agglomerated

The standard NF T 65-011 distinguishes the bitumen emulsions by their ionic nature (anionic or cationic), their stability with respect to agglomerates and weight content of base binder. There are 20 grades of emulsions. 

Very finely divided minerals may be difficult to purify by flotation since the particles may a ere to larger, undesired minerals—or vice versa, the fines may be an impurity to be removed. The latter is the case with Ii02 (anatase) impurity in kaolin clay [87]. In carrier flotation, a coarser, separable mineral is added that will selectively pick up the fines [88,89]. The added mineral may be in the form of a floe (ferric hydroxide), and the process is called adsorbing colloid flotation [90]. The fines may be aggregated to reduce their loss, as in the addition of oil to agglomerate coal fines [91]. 

Then tire pressure is reduced to transfonn tire frozen liquid to a vapour and to remove it. Freeze drying is commonly used to make powders tliat are not agglomerated. 

The speed of the method comes from two sources. First, all of the macroscopic cells of the same size have exactly the same internal structure, as they are simply formed of tessellated copies of the original cell, thus each has exactly the same multipole expansion. We need compute a new multipole expansion only once for each level of macroscopic agglomeration. Second, the structure of the periodic copies is fixed we can precompute a single transfer... 

Clarke,. 1. and Freakley, P.K., 1995. Modes of dispersive mixing and filler agglomerate size distributions in rubber compounds, Plast. Rubber Compos. Process. Appl. 24, 261-266. 

Prepare a saturated solution of sodium sulphide, preferably from the fused technical sodium polysulphide, and saturate it with sulphur the sulphur content should approximate to that of sodium tetrasulphide. To 50 ml. of the saturated sodium tetrasulphide solution contained in a 500 ml. round-bottomed flask provided with a reflux condenser, add 12 -5 ml. of ethylene dichloride, followed by 1 g. of magnesium oxide to act as catalyst. Heat the mixture until the ethylene dichloride commences to reflux and remove the flame. An exothermic reaction sets in and small particles of Thiokol are formed at the interface between the tetrasulphide solution and the ethylene chloride these float to the surface, agglomerate, and then sink to the bottom of the flask. Decant the hquid, and wash the sohd several times with water. Remove the Thiokol with forceps or tongs and test its rubber-like properties (stretching, etc.). 

Fig. 1.11 The external surface of the individual particles in I is partially converted into an internal surface (denoted by heavy lines) when the agglomerate in II is formed.

As pointed out earlier (Section 3.5), certain shapes of hysteresis loops are associated with specific pore structures. Thus, type HI loops are often obtained with agglomerates or compacts of spheroidal particles of fairly uniform size and array. Some corpuscular systems (e.g. certain silica gels) tend to give H2 loops, but in these cases the distribution of pore size and shape is not well defined. Types H3 and H4 have been obtained with adsorbents having slit-shaped pores or plate-like particles (in the case of H3). The Type I isotherm character associated with H4 is, of course, indicative of microporosity. 

An agglomeration of molecules containing ionic heads and hydrophobic tails, which form into a structure with a hydrophobic interior and a hydrophilic exterior. 

A second form of desolvation chamber relies on diffusion of small vapor molecules through pores in a Teflon membrane in preference to the much larger droplets (molecular agglomerations), which are held back. These devices have proved popular with thermospray and ultrasonic nebulizers, both of which produce large quantities of solvent and droplets in a short space of time. Bundles of heated hollow polyimide or Naflon fibers have been introduced as short, high-surface-area membranes for efficient desolvation. 

Agents, chemical warfare Agent VX [50782-69-9] Age-resistant elastomers AgeRiteDPPD [74-31-7] AgeRite White AgeRite Write [93-46-9] Ageusia Agglomeration... 

Drug testing Drum agglomerators Drum brakes Drum packages Drums Dry ash... 

Powder Preparation. The goal in powder preparation is to achieve a ceramic powder which yields a product satisfying specified performance standards. Examples of the most important powder preparation methods for electronic ceramics include mixing/calcination, coprecipitation from solvents, hydrothermal processing, and metal organic decomposition. The trend in powder synthesis is toward powders having particle sizes less than 1 p.m and Httie or no hard agglomerates for enhanced reactivity and uniformity. Examples of the four basic methods are presented in Table 2 for the preparation of BaTiO powder. Reviews of these synthesis techniques can be found in the Hterature (2,5). 

A fundamental requirement in powder processing is characterization of the as-received powders (10—12). Many powder suppHers provide information on tap and pour densities, particle size distributions, specific surface areas, and chemical analyses. Characterization data provided by suppHers should be checked and further augmented where possible with in-house characterization. Uniaxial characterization compaction behavior, in particular, is easily measured and provides data on the nature of the agglomerates in a powder (13,14). 

---