Adhesive application brushing

Latex adhesives replace solvent-based adhesives more easily than solution adhesives. Most latex adhesives are produced from polymers that were not designed for use as adhesives. This is why they require extensive formulation in order to obtain the proper appUcation and performance properties. Application methods for latex adhesives include brush, spray, roll coat, curtain coat, flow, and knife coat. The bonding techniques used for latex adhesives are similar to those used for solvent adhesives. The following techniques are popular ... 

Adhesives types Brush application Cold spray Hot spray... 

Primer and adhesive application are generally accomplished by spraying, brushing, tumbling or dipping. Each different application method has its own strengths and weaknesses. The choice of the application method is dependent on the size and shape of the parts, the number of parts to be coated, and whether the part is to be wholly or only partially coated. 

The application procedure (brush, doctor knife, spray gun, roller, coater) and the amount of adhesive must be carefully controlled. The choice of adhesive application devices depends mainly on the type and size of the materials to be bonded as well as on the rheological properties of the adhesive. Furthermore, the viscosity of the adhesive must be controlled and the operation times (evaporation rate of solvents or water, open time, shelf Kfe) must be strictly obeyed. 

The viscosity of elastomeric adhesives determines their method of application. Typically, solvent-borne rubber compounds require low viscosities for application. Thus, viscosities lower than 0.6 Pas for spray, curtain or dip applications are required, whereas for brush application viscosities lower than 5 Pa s are generally used. Roll- coating technology requires viscosities between 5 and 15 Pa s. 

Because most latices have low viscosities by compounding, most of the waterborne rubber adhesives are sprayable. Thickeners such as fumed silicas can be added to increase viscosity and thixotropy. This means that even at relatively large viscosities (over 10 Pas) many water-based rubber adhesives can be sprayed. Dip and curtain applications require viscosities between 0.05 and 0.3 Pas, whereas brush application works with viscosities between 1 and 50 Pa s. 

A characteristic of the group (a) of resins is that they air-dry solely by solvent evaporation and remain permanently solvent soluble. This fact, combined with the need to use strong solvents, makes brush application very difficult, but sprayed coats can be applied at intervals of one hour. A full vinyl system such as (o) possesses excellent chemical and water resistance. Many members of group (o) have very poor adhesion to metal, and have therefore been exploited as strip lacquers for temporary protection. Excellent adhesion is, however, obtained by initial application of an etching primer the best known of such primers comprises polyvinyl butyral, zinc tetroxy-chromate and phosphoric acid. 

By studying the properties of polymer layers on soHd surfaces it soon became obvious that not only is the chemical composition of the immobihzed polymer cmcial for the performance of the material, but so is its morphology. This has been recognized in various fields of applications e.g. stabihzation of small particles suspensions by attached polymer brush-type layers [159, 160], control of adhesion [161] or friction [162] and tailored stationary phases for chromatography [163-165]. 

There are several recent examples of the switching of nonspecific protein binding on polymer surfaces by application of an external stimulus. Alexander and coworkers demonstrated that protein adhesion can be controlled on PNIPAM surface brushes [14, 181]. For instance, it was reported that the adsorption of FITC-labeled bovine serum albumin (FITC-BSA) on PNIPAM/hexadecanethiol micropatterned surfaces could be tuned by LCST. However, this effect was found to be less pronounced after prolonged incubation times or repeated heating/cooling cycles. The authors suggested that this behavior could be due to unspecific PNIPAM-protein interactions [14],... 

Thermally responsive polymers, such as poly( V-isopropyl acrylamide) (NI-PAm), have also been studied extensively for applications related to those previously discussed [112], De las Heras et al. described the synthesis and patterning of NIPAm brushes on SAMs and their subsequent performance during temperature-dependent adhesion assays of BSA and Streptococcus mutans (Fig. 7). The authors employed p.CP to pattern features of hydrophobic hexadecanethiol and backfilled the surface with an initiator-functionalized alkanethiol. Polymer brushes were grown via surface-initiated atom transfer radical polymerization (ATRP). FITC-BSA was then... 

It provides for certain application characteristics of the adhesive (brush, spray, trowel,... 

The epoxy adhesives are usually applied by simple extrusion from dispensing nozzles, brushing, or troweling. However, spray equipment may be used in certain applications. Conventional spray equipment is used with solvent-borne epoxy adhesives, but frequent cleaning is generally required. For fast-reacting systems, dual-nozzle spray equipment is available. 

Brushes, simple rollers, syringes, squeeze bottles, and pressurized glue guns are manual methods that provide simplicity, low cost, and versatility. These methods are probably the most widely used because of their simplicity. Manual dispensing methods allow application of adhesive to only a small segment of a surface and are particularly effective for small or irregular parts or low-volume production. 

Bench coaters are roughly 20 to 35 percent faster than hand-brushing and cut waste by up to 20 to 35 percent. They start to be useful at rates of 200 pieces per day and can reach 12,000 pieces per day. Roller sizes range from 4 to 26 in, and they come with various surfaces from smooth for thin applications to increasingly coarse for heavier adhesive layers. 

Soft-soldering of copper, iron, steel, and brass objects of large size is usually accomplished by the use of a burner or hand torch, with an acid flux—frequently a concentrated aqueous solution of zinc chloride and ammonium chloride (2 1 ratio)—brushed onto the hot metal concurrently with the addition of solder. Initially, heat should be applied around the area to be soldered but not directly on the region to be soldered. If the region to be soldered is heated too much without the application of flux, an oxide coating will form that can make proper surface adhesion impossible. The surfaces to be joined should be pretinned if possible, and excess solder is shaken off or wiped off with a cloth. The two surfaces to be joined are then placed in contact and heated with the torch until the solder begins to flow more solder is then added as required, and the pieces are allowed to cool undisturbed. The finished work should be washed thoroughly with water to remove the flux. 

---