Adding the Reactions

Once all two reactions are entered and defined, you can create a reaction set for the conversion reactor. 

Still on the Reactions tab, click the Add Set button. Call the reaction set Oxidation Rxn Set, and add Rxn-1 and Rxn-2. Reactions are added by highlighting the empty field in the Active List group, and selecting the desired reaction from the drop down list. The view should look like this after you are finished  

Active List OK Inactive List f Derations Attached  

Conversion reactions can be grouped with other conversion reactions and ranked to operate either sequentially or simultaneously. Lowest ranking occurs first (may start with either 0 or 

To make the reactions operate sequentially, in the Oxidation Rxn Set, click the Ranking... and enter the information as shown  

---

When initiator is first added the reaction medium remains clear while particles 10 to 20 nm in diameter are formed. As the reaction proceeds the particle size increases, giving the reaction medium a white milky appearance. When a thermal initiator, such as AIBN or benzoyl peroxide, is used the reaction is autocatalytic. This contrasts sharply with normal homogeneous polymerizations in which the rate of polymerization decreases monotonicaHy with time. Studies show that three propagation reactions occur simultaneously to account for the anomalous auto acceleration (17). These are chain growth in the continuous monomer phase chain growth of radicals that have precipitated from solution onto the particle surface and chain growth of radicals within the polymer particles (13,18). 

Methyl chloride can be converted iato methyl iodide or bromide by refluxing ia acetone solution ia the presence of sodium iodide or bromide. The reactivity of methyl chloride and other aUphatic chlorides ia substitution reactions can often be iacteased by usiag a small amount of sodium or potassium iodide as ia the formation of methyl aryl ethers. Methyl chloride and potassium phthalimide do not readily react to give /V-methy1phtha1imide unless potassium iodide is added. The reaction to form methylceUulose and the Williamson synthesis to give methyl ethers are cataly2ed by small quantities of sodium or potassium iodide. 

In a 2-1. round-bottom flask, fitted with an efficient reflux condenser, is placed 500 g. (5.7 moles) of ethyl acetate (Note i), and 50 g. (2.2 moles) of clean sodium wire or finely sliced sodium (Note 2) is added. The reaction is at first quite slow, and must be started by warming on a water bath (Note 3). After the reaction is once started it proceeds vigorously and cooling is then necessary in order to avoid loss of material through the condenser. When the rapid reaction slows down, the reaction mixture is heated on a water bath until the sodium has completely dissolved. This usually requires about one and one-half hours. At this stage the reaction mixture should be a clear red liquid with a green fluorescence. 

To the acid chloride, mechanically stirred and heated on the steam bath, is added 2.5 kg. (805 ml. 15.6 moles) of dry bromine as rapidly as it will react (Note 5). The addition requires about 12 hours. The contents of the flask are stirred and heated an additional 2 hours, transferred to a dropping funnel (Note 6), and added in a thin stream to 5 1. of absolute ethyl alcohol, which has previously been placed in a 12-1. flask provided with a stopper carrying an effleient reflux condenser, a separatory funnel, and a mechanical stirrer. The resulting vigorous reaction is controlled by external cooling. After the dibromoacid chloride has been added, the reaction mixture is allowed to stand at room temperature overnight and is then poured into 5 1. of cold water. The top alcoholic aqueous layer is decanted and extracted once with 8 1. of ether. The oily bottom layer is dissolved in the ether extract, washed first with 1 1. of a 2% sodium bisulfite solution, then with two 1-1. portions of 3% sodium carbonate solution, and finally with several portions of water. The ether solution is dried over 175 g. of potassium carbonate the solvent is distilled on the steam bath. The yield of residual ester (Note 7) amounts to 2260-2400 g. (91-97% of the theoretical amount). 

After all the hydrogen peroxide is added, the reaction mixture is allowed to cool to room temperature and is then saturated with sodium chloride, after which it is extracted four times with 100-ml. portions of ether. The combined extracts are dried over sodium sulfate. The ether is removed by distillation on a steam bath, and the residue is then distilled under reduced pressure, Pyrogallol monomethyl ether is collected at 136-138°/22 mm. The yield is 38-44.5 g. (68-80%) of a colorless to light t11ow oil which solidifies on standing (Note 4). 

The white solid which collects inside the upper part of the flask is methylsulfur trichloride. This must be washed down with the cold reaction mixture before the flask warms to room temperature. The progress of the chlorination is accompanied by definite color changes. When one-third of the chlorine has been added, the reaction mixture is a deep reddish orange color which gradually fades as more chlorine is added until at the end the color should be a pale golden yellow or light straw color. 

A solution of hydrazoic acid (prepared from about 30 g sodium azide) in ca. 200 ml chloroform is prepared in a well-ventilated hood. Cholesterol (15 g) is dissolved in the hydrazoic acid solution and 3.5 ml of triethylamine is added. The reaction mixture is then stirred at room temperature while 7 g of A-chlorosuccinimide is added. The reaction mixture is allowed to stand overnight and then the chloroform solution is washed successively with dilute sodium bisulfite, dilute soldium bicarbonate solutions and finally with water. The chloroform extract is then dried (Na2S04) and the solvent removed in vacuo. The residue is crystallized from ethanol to yield ca. 8.5 g of (101) in colorless needles mp 138-139°. The chloro azide is reduced to the aziridine by lithium aluminum hydride according to the foregoing procedure. 

Estr-5(10)-ene-3a,17 -diol (10 g, 36.2 mmoles) is added over a period of 1 hr to a refluxing mixture consisting of 60 g (0.92 moles) of zinc-copper couple, 350 ml of dry ether and 180 g (54 ml, 0.67 moles) of methylene iodide. After the addition is complete, half of the solvent is removed by distillation and 200 ml dry ether is added. The reaction mixture is then transferred to a sealed stainless steel tube and maintained for 3 hr at 92° before being cooled in an ice bath and poured into 500 ml of saturated aqueous sodium bicarbonate solution. The resultant mixture is extracted with ether and the extracts are dried over anhydrous sodium sulfate and concentrated to yield a solid residue which gives 8.4 g (80%) 5,19-cyclo-5a,10a-androstane-3a,17) -diol mp 161-163° [aJo 40° (CHCI3), on crystallization from acetone. 

To a solution of dihydronaphthalene 41 (250 mg, 0.77 mmol) in CH2CI2 (5 mL) was added methyl trifluoromethanesulfonate (227 mg, 1.38 mmol). The mixture was stirred at rt until the starting material had been completely consumed as judged by TLC analysis (3 h). The mixture was cooled to 0°C and a solution of NaBHt (111 mg, 2.92 mmol) in 4 1 MeOH THF (3 mL) was slowly added. The mixture was warmed to rt then quenched with saturated aqueous ammonium chloride (50 mL). The resulting mixture was extracted with CH2CI2 (3 X 50 mL) and the combined organic extracts were dried over anhydrous sodium sulfate, filtered, and concentrated in vacuo. The resulting material was dissolved in 4 1 THF/H2O (5 mL) and oxalic acid (485 mg, 3.85 mmol) was added. The reaction... 

To a solution of 112 (2.0 g, 43.0 mmol) in 50 mL of dry THF at -65°C was added a solution of 111 (4.45 g, 34.0 mmol) in 100 mL of absolute ethanol containing 5 mL of acetic acid cooled to - 65°C in one portion. After stirring for 15 min., dry triethylamine (4.8 g, 510 mmol) was added. The reaction continued for 24 h with slow warming to room temperature before reducing the volume to 10 mL. The crude 113 was brought to pH 10 with potassium carbonate. The aqueous solution was continuously extracted with chloroform, dried (K2CO3), evaporated onto neutral alumina, placed on a column of neutral alumina (50 g) and eluted with chloroform. The solvent was evaporated and the residue crystallized from ethanol to yield 113 (2.86 g 55%). The yellow solid had a mp = 72.5-73.8°C. 

Secondary Chlorides With a low-boiling chloride such as 2-chlorobutane, a stirred slurry of 30 g (0.61 mole) of sodium cyanide in 150 ml of dimethyl sulfoxide is heated to 90° with a heating mantle, and 0.5 mole of the chloride is slowly added over a period of 30 minutes. The temperature of the refluxing reaction mixture slowly increases as nitrile is formed. Refluxing continues as the temperature slowly rises to 150° after 3 hours reaction time. The flask is then cooled and the reaction mixture is worked up in the same way as for the primary nitriles. With 2-chlorooctane, the sodium cyanide-dimethyl sulfoxide slurry is heated to 130° and 0.5 mole of the chloride added. The reaction mixture is maintained at 135-145° for 1 hour, then cooled, and the product is isolated as above. Examples are given in Table 16.1. 

In 212 cc of water are mixed 21.2 grams (0.112 mol) of N-(benzylidene)-3-amino-2-oxa-zolidone, 8.93 grams of concentrated sulfuric acid, and 30.1 grams (0.124 mol) of 5-ni-tro-2-furaldehyde diacetate. This mixture is heated to effect the hydrolysis of N-(benzy-lidene)-3-amino-2-oxazolidone, steam distillation of the benzaldehyde and hydrolysis of 5-nitro-2-furaldehyde diacetate. Approximately IV2 hours are required for this reaction to take place. When the bulk of the benzaldehyde has been removed, 50 cc of 99% isopropanol are added, the reaction mixture is refluxed a short time, and the crystals of N-(5-nitro-2-furfurylidene)-3-amino-2-oxazolidone are filtered from the hot suspension. The product is washed with water and isopropanol and dried a yield of 23.3 grams, 92.8% based on N-(benzylidene)-3-amino-2-oxazolidone of MP 254° to 256°C is obtained, according to U.S. Patent 2,759,931. 

In the final production preparation, a mixture of ethyl methyl(3-benzoylphenyl)cyano-acetate (48 g), concentrated sulfuric acid (125 cc) and water (125 cc) is heated under reflux under nitrogen for 4 hours, and water (180 cc) is then added. The reaction mixture is extracted with diethyl ether (300 cc) and the ethereal solution is extracted with N sodium hydroxide (300 cc). The alkaline solution is treated with decolorizing charcoal (2 g) and then acidified with concentrated hydrochloric acid (40 cc). An oil separates out, which is extracted with methylene chloride (450 cc), washed with water (100 cc) and dried over anhydrous sodium sulfate. The product is concentrated to dryness under reduced pressure (20 mm Hg) to give a brown oil (33.8 g). 

A mixture containing 8 g (0.06 mol) of N-methyl-3-chloro-piperidine and 13.6 g (0.06 mol) of benzilic acid in 50 cc of anhydrous isopropyl alcohol was refluxed for 3 days the isopropyl alcohol was removed by distillation in vacuo, the residue treated with dilute aqueous hydrochloric acid and the aqueous acid mixture extracted repeatedly with ether. The aqueous phase was separated, made strongly alkaline with 20% aqueous sodium hydroxide and extracted with ether. The ether extracts were dried with potassium carbonate and distilled the product was collected at 175° to 176°C (0.03 mm), yield 11.5 g (59%). The ester base thus prepared was then dissolved in 75 cc of isopropyl alcohol and 3.4 g (0.037 mol) methyl bromide added. The reaction mixture was allowed to stand at 30°C for 2 days and the product isolated by filtration, yield, 13 g (87%), MP 228° to 229°C dec. 

A Preparation of 11 -Methoxy-A -Estradiene-3,17-Dione 0.5 g of A -estradiene-11/3-ol-3,17-dione were dissolved at room temperature in 25 cc of methylene chloride containing 2% of methanol and after 5 mg of p-toluene-sulfonic acid were added, the reaction mixture was agitated for several minutes. Then the reaction mixture was poured into ice water, washed with water until the wash waters were neutral, and distilled to dryness under vacuum. The resulting residue was crystallized from ethyl ether to obtain 0.46 g of 11/3-methoxy-A -estradiene-3,17-dione having a MP of 140°C. 

When all the ethyl nitrite has been added, the reaction mixture is refluxed for approximately one hour, then concentrated to dryness under reduced pressure (25 to 30 mm Hg) and at a maximum temperature of 70°C. The crystalline residue is dissolved in 35 liters of water and adjusted to a pH of 8 to 9 by addition (with cooling and stirring) of 11 to 12 kg of caustic soda. The sodium chloride formed is filtered off, and the filter cake is washed with 20 liters of normal butyl alcohol. This wash liquid is used for the first extraction of the product from the aqueous filtrate. The filtrate is then further extracted with four successive 20-liter portions of n-butyl alcohol. 

The stream of dry air is continued for about six hours or until most of the hydrogen chloride has been expelled and then another 55 grams of thionyl chloride is added. The reaction mixture is allowed to stand twenty-four hours, a few drops of pyridine are added and the mixture heated 4 hours on the steam bath. The cooled reaction mixture is poured into water, the crude product is washed with dilute sodium bicarbonate solution and finally taken up in benzene. The benzene is distilled at ordinary pressure and the residue distilled in vacuo to yield 60-70% of Tphenoxy-2-chloropropane, BP 93°-94°C/5 mm. 

B) A solution of (SM) (330 mg) in trifluoroacetic acid (7 ml) was kept under nitrogen at room temperature for 15 minutes. Ether (100 ml) was added and the precipitate was filtered, washed thoroughly with ether and dried. This material (300 mg) was added in portions to concentrated sulfuric acid (18 ml) cooled at -20°C with vigorous stirring. After 15 minutes a solution of potassium bisulfate in concentrated sulfuric acid (408 mg in 3 ml) was added. The reaction mixture was stirred for 75 minutes at -15°Cand then stored at -7°Cfor 285 minutes. The sulfuric acid solution was poured into cold ether (400 ml) precipitate was filtered, washed with cold ether, and suspended in cold water. Complete solution was then achieved by careful addition of 2N sodium hydroxide. Acidification with N hydrochloric acid led to the precipitation of the desired octapeptide sulfate ester. Yield 200 mg. 

After the mixture had been stirred for 30 minutes, 3 g of N,N-diethylethylenediamine were added. The reaction mixture was stirred for 6 hours and the solvents were evaporated under vacuum. 

---