Acetanilide acidity

White crystals, m.p. 114" C. Manufactured by reacting aniline with excess ethanoic acid or ethanoic anhydride. Chief use is in the manufacture of dye intermediates such as p-nitro-acetanilide, p-nitroaniline and p-phenylene-diamine, in the manufacture of rubber, and as a peroxide stabilizer. 

On acetylation it gives acetanilide. Nitrated with some decomposition to a mixture of 2-and 4-nitroanilines. It is basic and gives water-soluble salts with mineral acids. Heating aniline sulphate at 190 C gives sulphanilic add. When heated with alkyl chlorides or aliphatic alcohols mono- and di-alkyl derivatives are obtained, e.g. dimethylaniline. Treatment with trichloroethylene gives phenylglycine. With glycerol and sulphuric acid (Skraup s reaction) quinoline is obtained, while quinaldine can be prepared by the reaction between aniline, paraldehyde and hydrochloric acid. 

Hydrolysis of Acetanilide. Anilides in general, such as acetanilide and benzanilide (p. 245), may be hydrolysed by caustic alkalis or by acids. Alkaline hydrolysis, however, is usually very slow, and therefore... 

Place I g. of acetanilide and 10 ml. of the 70% sulphuric acid in a small flask fitted with a reflux water-condenser, and boil the mixture gently for 15 minutes, when the hot solution will smell perceptibly of... 

Dissolve I g. of finely powdered acetanilide in 5 ml. of cold glacial acetic acid contained in a 25 ml. conical flask. Then in another small flask prepare a solution of 0 42 ml. (1 34 g.) of bromine (care ) in 6 ml. of glacial acetic acid, and add this solution slowly to the acetanilide solution, shaking the latter throughout the addition to ensure thorough mixing. Allow the final mixture to stand at room temperature for 15 minutes. Then... 

Required Acetanilide, 10 g. acetic acid, 10 ml. sulphuric acid, 20 ml. fuming nitric acid, 4 ml. 

Hydrolysis to p-Nitroaniline. For this purpose use 70 sulphuric acid, the usual reagent employed for the hydrolysis of anilides (p. 108). Add 5 g. of the recrystallised />-nitro-acetanilide to 30 ml. of 70%sulphuric acid, and boil the mixture gently under a reflux water-condenser for 20 minutes. Then pour the clear hot solution into about 150 ml. of cold water, and finally add an excess of sodium hydroxide solution until precipitation of the yellow p-nitroaniline is complete. Coo the mixture in ice-water if necessary, and then filter at the pump, wash well... 

Sulphanilamide, the simplest member of a large series of bacteriostatic drugs, can readily be prepared by the following reactions. Acetanilide, when treated v ith an excess of chlorosulphonic acid, gives p-acetaniidobenzencsulphonyl chloride (Reaction A), w hich readily reacts with ammonia to give p-acetamido-benzenesulphonamide (Reaction H). The acetamido-group in the latter... 

Hydrolysis of Benzanilide. For this hydrolysis, it is necessary to use 70% sulphuric acid (see Hydrolysis of Acetanilide, p. 108). Add I g. of benzanilide to 10 ml. of 70% sulphuric acid, and boil the mixture gently in a small flask under a reflux water-condenser for 30 minutes. Hydrolysis will now be complete, but much of the benzoic acid will have vaporised in the steam and then solidified in the conden-... 

The mixed bases are boiled with an acetic acid-acetic anhydride mixture to convert the aniline into acetanilide. The product is poured into water, when the acetanilide crystallises out while the quinoline remains in solution as quinoline acetate. The acetanilide is filtered off, and the filtrate made alkaline and steam-distilled. 

Substances suitable for the estimation acetanilide, sucrose, glucose, cinnamic acid, diphenyl amine, salicylic acid, vanillin, />"bromoacetanilide, toluene p-sul phonamide. 

Dilute hydrochloric or sulphuric acid finds application in the extraction of basic substances from mixtures or in the removal of basic impurities. The dilute acid converts the base e.g., ammonia, amines, etc.) into a water-soluble salt e.g., ammonium chloride, amine hydrochloride). Thus traces of aniline may be separated from impure acetanilide by shaking with dilute hydrochloric acid the aniline is converted into the soluble salt (aniline hydrochloride) whilst the acetanilide remains unaffected. 

Choice of solvent for recrystallisation. Obtain small samples (about 0 5 g.) of the following compounds from the storeroom (i) salicylic acid, (Li) acetanilide, (iii) m-dinitrobenzene, (iv) naphthalene, and (v) p-toluene-sulphonamide. Use the following solvents distilled water, methylated spirit, rectified spirit, acetone, benzene and glacial acetic acid. 

Add 25 g. of finely-powdered, dry acetanilide to 25 ml. of glacial acetic acid contained in a 500 ml. beaker introduce into the well-stirred mixture 92 g. (50 ml.) of concentrated sulphuric acid. The mixture becomes warm and a clear solution results. Surround the beaker with a freezing mixture of ice and salt, and stir the solution mechanically. Support a separatory funnel, containing a cold mixture of 15 -5 g. (11 ml.) of concentrated nitric acid and 12 -5 g. (7 ml.) of concentrated sulphuric acid, over the beaker. When the temperature of the solution falls to 0-2°, run in the acid mixture gradually while the temperature is maintained below 10°. After all the mixed acid has been added, remove the beaker from the freezing mixture, and allow it to stand at room temperature for 1 hour. Pour the reaction mixture on to 250 g. of crushed ice (or into 500 ml. of cold water), whereby the crude nitroacetanilide is at once precipitated. Allow to stand for 15 minutes, filter with suction on a Buchner funnel, wash it thoroughly with cold water until free from acids (test the wash water), and drain well. Recrystallise the pale yellow product from alcohol or methylated spirit (see Section IV,12 for experimental details), filter at the pump, wash with a httle cold alcohol, and dry in the air upon filter paper. [The yellow o-nitroacetanihde remains in the filtrate.] The yield of p-nitroacetanihde, a colourless crystalline sohd of m.p. 214°, is 20 g. 

The reaction is illustrated by the conversion of 3 5-dinitrobenzoic acid into 3 5-dlnltroaniline, and of acetophenone into acetanilide ... 

Acetanilide from acetophenone. Dissolve 12 g. of acetophenone in 100 ml. of glacial acetic acid containing 10 g. of concentrated sulphuric acid. To the stirred solution at 60-70°, add 9 8 g. of sodium azide in small portions at such a rate that the temperature does not rise above 70°. Stir the mixture with gentle heating until the evolution of nitrogen subsides (2-3 hours) and then allow to stand overnight at room temperature. Pour the reaction mixture on to 300 g. of crushed ice, filter the solid product, wash it with water and dry at 100°. The yield of crude acetanilide, m.p. 111-112°, is 13 g. Recrystallisation from water raises the m.p. to 114°. 

The reaction may be more easily controlled and the chlorosulphonic acid added all at once if the acetanilide is employed in the form of a hard cake. The latter is prepared by melting the acetanilide in the flask over a free flame and causing the compound to solidify over the lower part of the flask by swirling the liquid. If the reaction becomes too vigorous under these conditions, cool the flask momentarily by immersion in an ice bath. 

Hydrolysis of a substituted amide. A. With 10 per cent, sulphuric acid. Reflux 1 g. of the compound (e.g., acetanilide) with 20 ml. of 10 per cent, sulphuric acid for 1-2 hours. Distil the reaction mixture and collect 10 ml. of distillate this will contain any volatile organic acids which may be present. Cool the residue, render it alkaline with 20 per cent, sodium hydroxide solution, cool, and extract with ether. Distil off the ether and examine the ether-soluble residue for an amine. 

Without further studies little weight can be given to these ideas. In particular there is the possibility that with acetanilide, as with anisole, nitrosation is of some importance, and further with nitrations in sulphuric acid the effect of protonation of the substrate needs quantitative evaluation. The possibility that the latter factor may be important has been recognised, and it may account for the difference between nitration in sulphuric acid and nitration with nitronium tetrafluoroborate. 

Other substituents which belong with this group have already been discussed. These include phenol, anisole and compounds related to it ( 5.3.4 the only kinetic data for anisole are for nitration at the encounter rate in sulphuric acid, and with acetyl nitrate in acetic anhydride see 2.5 and 5.3.3, respectively), and acetanilide ( 5.3.4). The cations PhSMe2+, PhSeMe2+, and PhaO+ have also been discussed ( 9.1.2). Amino groups are prevented from showing their character ( — 7 +717) in nitration because conditions enforce reaction through the protonated forms ( 9.1.2). 

Conversion of aniline to acetanilide [103-84-4] by reaction with acetic anhydride, is a convenient method for protecting the amino group. The acetyl group can later be removed by acid or base hydrolysis. 

Nitration. Direct nitration of aromatic amines with nitric acid is not a satisfactory method, because the amino group is susceptible to oxidation. The amino group can be protected by acetylation, and the acetylamino derivative is then used in the nitration step. Nitration of acetanilide in sulfuric acid yields the 4-nitro compound that is hydroly2ed to -rutroaruline [100-01-6]. 

Production is by the acetylation of 4-aminophenol. This can be achieved with acetic acid and acetic anhydride at 80°C (191), with acetic acid anhydride in pyridine at 100°C (192), with acetyl chloride and pyridine in toluene at 60°C (193), or by the action of ketene in alcohoHc suspension. 4-Hydroxyacetanihde also may be synthesized directiy from 4-nitrophenol The available reduction—acetylation systems include tin with acetic acid, hydrogenation over Pd—C in acetic anhydride, and hydrogenation over platinum in acetic acid (194,195). Other routes include rearrangement of 4-hydroxyacetophenone hydrazone with sodium nitrite in sulfuric acid and the electrolytic hydroxylation of acetanilide [103-84-4] (196). 

GK [10343-58-5] (S ) (Cl Acid Yellow 99 Cl 13900) (4-nitro-2-aminophenol —> aceto acetanilide) and Palatine FastRedBEN [6656-02-6] (59) (Cl Acid Red 214 Cl 19355) (2-amiao-6-nitroplienol-4-sulfonic acid — 2,4-dihydroxyquiQoline). 

---