Acetal polymer

PVF resins [VINYL POLYhffiRS - VINYL ACETAL POLYMERS] (Vol 24)... 

Poly(vinyl acetal). See Vinyl acetal polymers. 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

The solution process consists of four steps preparation of cellulose for acetylation, acetylation, hydrolysis, and recovery of cellulose acetate polymer and solvents. A schematic of the total acetate process is shown in Figure 9. 

Acetate and triacetate polymers are white amorphous soHds produced in granular, flake, powder, or fibrous form. They are used as raw materials in the preparation of fibers, films, and plastics. Polymer density varies and ranges from 100 kg/m for the fibrous form to 500 kg/m for granules. Acetate polymer is shipped by trailer tmck, railroad freight car, or multiwaH bags. 

OOCCH3 vinyl acetate A-CH2—CH Vinyl POLYMERS, vinyl acetate polymers... 

Low DS starch acetates have reduced gelatinization temperature ranges and reduced tendency to retrograde after pasting and cooling. Gelling may be completely inhibited if the DS is sufficiently high. Low DS starch acetate polymers also form films which are useful in textile and paper manufacture. 

Vinyl acetal polymers are made by the acid-cataly2ed acetalization of poly(viQyl alcohol) [9002-89-5] with aldehydes (1). 

Poly(vinyl alcohol) used to manufacture the poly(vinyl acetal)s is made from poly(vinyl acetate) homopolymer (see Vinyl polymers, vinyl alcohol polymers Vinyl POLYMERS, vinyl acetate polymers). Hydrolysis of poly(vinyl acetate) homopolymer produces a polyol with predominandy 1,3-glycol units. The polyol also contains up to 2 wt % 1,2-glycol units that come from head-to-head bonding during the polymeri2ation of vinyl acetate monomer. Poly(vinyl acetate) hydrolysis is seldom complete, and for some appHcations, not desired. For example, commercial PVF resins may contain up to 13 wt % unhydroly2ed poly(vinyl acetate). Residual vinyl acetate units on the polymer help improve resin solubiHty and processibiHty (15). On the other hand, the poly(vinyl alcohol) preferred for commercial PVB resins has less than 3 wt % residual poly(vinyl acetate) units on the polymer chain. 

Tackifiers are used to increase the tackiness and the setting speed of adhesives. They increase tackiness by softening the poly(vinyl acetate) polymer in the wet and the dry adhesive film. Tackifiers are usually rosin or its derivatives or phenoHc resins. Other additives frequently needed for specific apphcation and service conditions are antifoams, biocides, wetting agents, and humectants. 

Vinyl acetate polymers have long been used as chewing gum bases. They have been studied as controUed release agents for programmed administration of dmgs and as a base for antifouling marine paints (166,167). 

PVC should not be melt-mixed with acetal polymers. These polymers are chemically incompatible mixing could cause rapid decomposition and gas evolution. 

Acetate fibers are dyed usually with disperse dyes specially synthesized for these fibers. They tend to have lower molecular size (low and medium energy dyes) and contain polar groups presumably to enhance the forces of attraction by hydrogen bonding with the numerous potential sites in the cellulose acetate polymer (see Fibers cellulose esters). Other dyes can be appHed to acetates such as acid dyes with selected solvents, and azoic or ingrain dyes can be apphed especially for black colorants. However thek use is very limited. 

Tension Above materials plus High-density polyethylene Polypropylene Acetal polymers Aliphatic polyamides (nylons) PPO Poly(ethylene terephthalate) Polysulphones... 

MATTHEWS, G. A. R., Vinyl and Allied Polymers Vol. II, Vinyl Chloride and Vinyl Acetate Polymers, lliffe, London (1972). 

---