Useful work

To determine the influence degree on both types of structure and volume of structural heterogeneity on the frequency spectrum characteristics of an ultrasonic pulse, research work using angle beam and straight beam probes was performed... 

The traditional, essentially phenomenological modeling of boundary lubrication should retain its value. It seems clear, however, that newer results such as those discussed here will lead to spectacular modification of explanations at the molecular level. Note, incidentally, that the tenor of recent results was anticipated in much earlier work using the blow-off method for estimating the viscosity of thin films [68]. 

For an overview of Professor Carter s group s work using pseudospectral methods, see ... 

The differentiation of bridged nonclassical from rapidly equilibrating classical carbocations based on NMR spectroscopy was difficult because NMR is a relatively slow physical method. We addressed this question in our work using estimated NMR shifts of the two structurally differing ions in comparison with model systems. Later, this task... 

Precision is a measure of the spread of data about a central value and may be expressed as the range, the standard deviation, or the variance. Precision is commonly divided into two categories repeatability and reproducibility. Repeatability is the precision obtained when all measurements are made by the same analyst during a single period of laboratory work, using the same solutions and equipment. Reproducibility, on the other hand, is the precision obtained under any other set of conditions, including that between analysts, or between laboratory sessions for a single analyst. Since reproducibility includes additional sources of variability, the reproducibility of an analysis can be no better than its repeatability. 

Once a mass spectrum from an eluting component has been acquired, the next step is to try to identify the component either through the skill of the mass spectroscopist or by resorting to a library search. Most modem GC/MS systems with an attached data station include a large library of spectra from known compounds (e.g., the NIST library). There may be as many as 50,000 to 60,000 stored spectra covering most of the known simple volatile compounds likely to be met in analytical work. Using special search routines under the control of the computer, one can examine... 

Synthetic Fuels. Hydrocarbon Hquids made from nonpetroleum sources can be used in steam crackers to produce olefins. Fischer-Tropsch Hquids, oil-shale Hquids, and coal-Hquefaction products are examples (61) (see Fuels, synthetic). Work using Fischer-Tropsch catalysts indicates that olefins can be made directly from synthesis gas—carbon monoxide and hydrogen (62,63). Shape-selective molecular sieves (qv) also are being evaluated (64). 

Electrochemical Process. Applying an electrical current to a brine solution containing propylene results in oxidation of propylene to propylene oxide. The chemistry is essentially the same as for the halohydrin process. AH of the chemistry takes place in one reactor. Most of the reported work uses sodium or potassium bromide as the electrolyte. Bromine, generated from bromide ions at the anode, reacts with propylene and water to form propylene bromohydrin. Hydroxide generated at the cathode then reacts with the bromohydrin to yield propylene oxide (217—219). The net reaction involves transfer of two electrons ... 

The majority of industrial research describes classical approaches to yield improvement (49). However, there has been some work using genetically modified organisms. In the case of these recombinant organisms, the carotenoid biosynthetic gene cluster has been expressed in noncarotegenic species such as E. coli (50) and S. cerevisiae (51). 

A progressive etching technique (39,40), combined with x-ray diffraction analysis, revealed the presence of a number of a polytypes within a single crystal of sihcon carbide. Work using lattice imaging techniques via transmission electron microscopy has shown that a-siUcon carbide formed by transformation from the P-phase (cubic) can consist of a number of the a polytypes in a syntactic array (41). 

Subdivision or discretization of the flow domain into cells or elements. There are methods, called boundary element methods, in which the surface of the flow domain, rather than the volume, is discretized, but the vast majority of CFD work uses volume discretization. Discretization produces a set of grid lines or cuives which define a mesh and a set of nodes at which the flow variables are to be calculated. The equations of motion are solved approximately on a domain defined by the grid. Curvilinear or body-fitted coordinate system grids may be used to ensure that the discretized domain accurately represents the true problem domain. 

The basic phenomenon was observed in modeling studies by Bjoreskov and Slinko (1965) that sudden increase in inlet temperature caused a transient drop of the peak temperature. The wrong-way response name was given by Mechta et al (1981) after they experienced the opposite a sudden of inlet temperature resulted in an increase of the peak temperature (which may eventually cause a runaway.) The work used a pseudo-homogeneous reaction model and explained the phenomenon by the different speeds of transient response in gas and solid. The example in the last part of Chapter 7.4 explained the speed difference by the large difference in heat capacity of gas and solid phases. For this a two-phase model is needed and spatial and time changes must be followed. 

Distribution of work used by the liquefaction process (Basis 1 lb of 1,000 psia stream)... 

Nutzen, m. use, utility, advantage, profit. Nutz-gas, n. (Aero.) impellent, -gras, n. grass for feed, -holz, n. commercial timber, lumber, -kapazitat, /. useful capacity, -last, /. useful load, pay load, -leistung,/. useful work, useful effect, effective output. nlltzUch, a. useful, serviceabla profitable, advantageous, expedient. 

Polystyrene (PS) is the fourth big-volume thermoplastic. Styrene can be polymerized alone or copolymerized with other monomers. It can be polymerized by free radical initiators or using coordination catalysts. Recent work using group 4 metallocene combined with methylalumi-noxane produce stereoregular polymer. When homogeneous titanium catalyst is used, the polymer was predominantly syndiotactic. The heterogeneous titanium catalyst gave predominantly the isotactic. Copolymers with butadiene in a ratio of approximately 1 3 produces SBR, the most important synthetic rubber. 

The search for alternative ways to produce monomers and chemicals from sources other than oil, such as coal, has revived working using Fisher Tropseh technology, which produces in addition to fuels, light olefins, sulfur, phenols, etc. These could he used as feedstocks for petrochemicals as indicated in Chapter 4. 

The chapter by Haynes et al. describes the pilot work using Raney nickel catalysts with gas recycle for reactor temperature control. Gas recycle provides dilution of the carbon oxides in the feed gas to the methanator, hence simulating methanation of dilute CO-containing gases which under adiabatic conditions gives a permissible temperature rise. This and the next two papers basically treat this approach, the hallmark of first-generation methanation processes. 

---