Turbine example

Solution (a) The turbine operates under the same conditions as the turbine Example 7.5, where we found... 

A more sophisticated and increasingly popular method of on-condItion maintenance is to monitor the performance of equipment on-line. For example, a piece of rotating equipment such as a turbine may be monitored for vibration and mechanical performance (speed, inlet and outlet pressure, throughput). If a base-line performance is established, then deviations from this may indicate that the turbine has a mechanical problem which will reduce its performance or lead to failure. This would be used to alert the operators that some form of repair is required. 

This type of coil was prepared from copper cladded printed circuit board material by applying photolithographic techniques. The p.c. board material is available with difierent copper thicknesses and with either a stiff or a flexible carrier. The flexible material offers the opportunity to adapt the planar coil to a curved three dimensional test object. In our turbine blade application this is a major advantage. The thickness of the copper layer was chosen to be 17 pm The period of the coil was 100 pm The coils were patterned by wet etching, A major advantage of this approach is the parallel processing with narrow tolerances, resulting in many identical Eddy current probes. An example of such a probe is shown in fig. 10. 

The first example refers to the inspection of turbine blades Customers ask for a system which... 

Hot Corrosion. Hot corrosion is an accelerated form of oxidation that arises from the presence not only of an oxidizing gas, but also of a molten salt on the component surface. The molten salt interacts with the protective oxide so as to render the oxide nonprotective. Most commonly, hot corrosion is associated with the condensation of a thin molten film of sodium sulfate [7757-82-6], Na2S04, on superaHoys commonly used in components for gas turbines, particularly first-stage turbine blades and vanes. Other examples of hot corrosion have been identified in energy conversion systems, particularly coal gasifiers and direct coal combustors. In these cases the salt originates from alkali impurities in the coal which condense on the internal... 

Low Expansion Alloys. Binary Fe—Ni alloys as well as several alloys of the type Fe—Ni—X, where X = Cr or Co, are utilized for their low thermal expansion coefficients over a limited temperature range. Other elements also may be added to provide altered mechanical or physical properties. Common trade names include Invar (64%Fe—36%Ni), F.linvar (52%Fe—36%Ni—12%Cr) and super Invar (63%Fe—32%Ni—5%Co). These alloys, which have many commercial appHcations, are typically used at low (25—500°C) temperatures. Exceptions are automotive pistons and components of gas turbines. These alloys are useful to about 650°C while retaining low coefficients of thermal expansion. Alloys 903, 907, and 909, based on 42%Fe—38%Ni—13%Co and having varying amounts of niobium, titanium, and aluminum, are examples of such alloys (2). 

Other alloys have been developed for use in particular corrosive environments at high temperatures. Several of these are age-hardenable alloys which contain additions of aluminum and titanium. Eor example, INCONEL alloys 718 and X-750 [11145-80-5] (UNS N07750) have higher strength and better creep and stress mpture properties than alloy 600 and maintain the same good corrosion and oxidation resistance. AHoy 718 exhibits excellent stress mpture properties up to 705°C as well as good oxidation resistance up to 980°C and is widely used in gas turbines and other aerospace appHcations, and for pumps, nuclear reactor parts, and tooling. 

Most nuclear reactors use a heat exchanger to transfer heat from a primary coolant loop through the reactor core to a secondary loop that suppHes steam (qv) to a turbine (see HeaT-EXCHANGETECHNOLOGy). The pressurized water reactor is the most common example. The boiling water reactor, however, generates steam in the core. 

A wide variety of turbine types and arrangements are used in modem power plants. For example, some smaH industrial plants may use only a single condensing turbine. Prepackaged steam/turbine generator systems can be economical for small-to-midsize instaHations. 

Another example of a topping cycle cogeneration system is one based on recovering the thermal energy exhausting from a gas turbine/generator. 

Validation and Application. VaUdated CFD examples are emerging (30) as are examples of limitations and misappHcations (31). ReaUsm depends on the adequacy of the physical and chemical representations, the scale of resolution for the appHcation, numerical accuracy of the solution algorithms, and skills appHed in execution. Data are available on performance characteristics of industrial furnaces and gas turbines systems operating with turbulent diffusion flames have been studied for simple two-dimensional geometries and selected conditions (32). Turbulent diffusion flames are produced when fuel and air are injected separately into the reactor. Second-order and infinitely fast reactions coupled with mixing have been analyzed with the k—Z model to describe the macromixing process. 

The second law can also suggest appropriate corrective action. Eor example, in combustion, preheating the air or firing at high pressure in a gas turbine, as is done for an ethylene (qv) cracking furnace, improves energy efficiency by reducing the lost work of combustion (Eig. 4). 

Most gas turbine appHcations in the chemical industry are tied to the steam cycle, but the turbines can be integrated anywhere in the process where there is a large requirement for fired fuel. An example is the use of the heat in the gas turbine exhaust as preheated air for ethylene cracking furnaces as shown in Figure 4 (8). 

---