Tantalum elements

Owing to lanthanide contraction, niobium and tantalum have virtually identical atomic rad (1.47 A) and close ionization energies (Nb6.67, Ta7.3eV), and usually display very similt chemical behavior. Some definite differences can however be noted these can usually be trace to the lower sensitivity of tantalum to reduction and to its higher affinity for dioxygen. lb tantalum-element multiple bonds are usually stabler, while MfiXg arrangements are so ft known only for niobium. 

Before it was known that elements beyond uranium were capable of existence, the heaviest known natural elements, thorium, protactinium and uranium, were placed in a sixth period of the periodic classification, corresponding to the elements hafnium, tantalum and tungsten in the preceding period. It was therefore implied that these elements were the beginning of a new, fourth transition series, with filling of the penultimate n = 6 level (just as the penultimate = 5... 

Gr. Tantalos, mythological character, father of Niobe) Discovered in 1802 by Ekeberg, but many chemists thought niobium and tantalum were identical elements until Rowe in 1844, and Marignac, in 1866, showed that niobic and tantalic acids were two different acids. The early investigators only isolated the impure metal. The first relatively pure ductile tantalum was produced by von Bolton in 1903. Tantalum occurs principally in the mineral columbite-tantalite. 

Separation of tantalum from niobium requires several complicated steps. Several methods are used to commercially produce the element, including electrolysis of molten potassium fluorotantalate, reduction of potassium fluorotantalate with sodium, or reacting tantalum carbide with tantalum oxide. Twenty five isotopes of tantalum are known to exist. Natural tantalum contains two isotopes. 

Tantalum is a gray, heavy, and very hard metal. When pure, it is ductile and can be drawn into fine wire, which is used as a filament for evaporating metals such as aluminum. Tantalum is almost completely immune to chemical attack at temperatures below ISOoC, and is attacked only by hydrofluoric acid, acidic solutions containing the fluoride ion, and free sulfur trioxide. Alkalis attack it only slowly. At high temperatures, tantalum becomes much more reactive. The element has a melting point exceeded only by tungsten and rhenium. Tantalum is used to make a variety... 

Europium is now prepared by mixing EU2O3 with a 10%-excess of lanthanum metal and heating the mixture in a tantalum crucible under high vacuum. The element is collected as a silvery-white metallic deposit on the walls of the crucible. 

Terbium has been isolated only in recent years with the development of ion-exchange techniques for separating the rare-earth elements. As with other rare earths, it can be produced by reducing the anhydrous chloride or fluoride with calcium metal in a tantalum crucible. Calcium and tantalum impurities can be removed by vacuum remelting. Other methods of isolation are possible. 

Study of the chemical properties of element 104 has confirmed that it is indeed homologous to hafnium as demanded by its position in the Periodic Table (20). Chemical studies have been made for element 105, showing some similarity to tantalum (25) no chemical studies have been made for elements 106—109. Such studies are very difficult because the longest-Hved isotope of 104 ( 104) has a half-Hfe of only about 1 min, of 105 ( 105) a half-Hfe of about 40 s, of 106 ( 106) a half-Hfe of about 1 s, and of elements 107—109 half-Hves in the range of milliseconds. 

Density is a particularly important characteristic of alloys used in rotating machinery, because centrifugal stresses increase with density. Densities of the various metals in Table 1 range from 6.1 to 19.3 g/cm. Those of iron, nickel, and cobalt-base superaHoys fall in the range 7-8.5 g/cm. Those alloys which contain the heavier elements, ie, molybdenum, tantalum, or tungsten, have correspondingly high densities. 

Tungsten with the addition of as much as 5% thoria is used for thermionic emission cathode wires and as filaments for vibration-resistant incandescent lamps. Tungsten—rhenium alloys are employed as heating elements and thermocouples. Tantalum and niobium form continuous soHd solutions with tungsten. Iron and nickel are used as ahoy agents for specialized appHcations. 

Niobium, discovered by Hatchett ia 1801, was first named columbium. In 1844, Rosed thought he had found a new element associated with tantalum (see Tantalum AND tantalum compounds). He called the new element niobium, for Niobe, daughter of Tantalus of Greek mythology. In 1949, the Union of Pure and Apphed Chemistry setded on the name niobium, but in the United States this metal is stiU known also as columbium. Sometimes called a rare metal, niobium is actually more abundant in the earth s cmst than lead. 

The most common oxidation state of niobium is +5, although many anhydrous compounds have been made with lower oxidation states, notably +4 and +3, and Nb can be reduced in aqueous solution to Nb by zinc. The aqueous chemistry primarily involves halo- and organic acid anionic complexes. Virtually no cationic chemistry exists because of the irreversible hydrolysis of the cation in dilute solutions. Metal—metal bonding is common. Extensive polymeric anions form. Niobium resembles tantalum and titanium in its chemistry, and separation from these elements is difficult. In the soHd state, niobium has the same atomic radius as tantalum and essentially the same ionic radius as well, ie, Nb Ta = 68 pm. This is the same size as Ti ... 

Minor amounts of tantalum, tin, lead, bismuth, and other elements also occur ia the ferroniobium. After cooling for 12—30 h, the metal is separated from the slag and cmshed and si2ed for shipment. The recovery of niobium ia the alurninothermic reaction is 87—93%. Larger reactions generally give better recoveries. 

Tantalum [7440-25-7] atomic number 73, is the heaviest element in Group 5 (VA) of the Periodic Table. This tough, ductile, silvery gray metal has an atomic weight of 180.948 amu. The element was discovered by A. K. Ekeberg in 1802 in minerals taken from Kimito, Finland, and Ytterby, Sweden (1). 

The first commercial use of tantalum was as filaments ia iacandescent lamps but it was soon displaced by tungsten. Tantalum is used ia chemical iadustry equipment for reaction vessels and heat exchangers ia corrosive environments. It is usually the metal of choice for heating elements and shields ia high temperature vacuum sintering furnaces. In 1994, over 72% of the tantalum produced ia the world went iato the manufacturiag of over 10 x 10 soHd tantalum capacitors for use ia the most demanding electronic appHcations. 

Interior of capacitive element containing tantalum, tantalum pentoxide (dielectric), manganese dioxide (solid electroyte)... 

Typical equipment made from tantalum includes heat exchangers, reaction vessels liners, thermowells, and heating elements or heat shields for high temperature vacuum sintering furnaces. Tantalum fabricated parts are found in the manufacturing of pharmaceuticals, explosives, insecticides, dyes, acidic baskets for silver cyanide barrel platers, and in hydrochloric and hydrobromic acid condensers. 

Tantalum Nitrides. Tantalum nitride [12033-62-4] TaN, is produced by direct synthesis of the elements at 1100°C. Very pure TaN has been produced by spontaneous reaction of lithium amide, L1NH2, and TaCl ( )- The compound is often added to cermets in 3—18 wt %. Ta N [12033-94-2] is used as a red pigment in plastics and paints (78). 

The important (3-stabilizing alloying elements are the bcc elements vanadium, molybdenum, tantalum, and niobium of the P-isomorphous type and manganese, iron, chromium, cobalt, nickel, copper, and siUcon of the P-eutectoid type. The P eutectoid elements, arranged in order of increasing tendency to form compounds, are shown in Table 7. The elements copper, siUcon, nickel, and cobalt are termed active eutectoid formers because of a rapid decomposition of P to a and a compound. The other elements in Table 7 are sluggish in their eutectoid reactions and thus it is possible to avoid compound formation by careful control of heat treatment and composition. The relative P-stabilizing effects of these elements can be expressed in the form of a molybdenum equivalency. Mo (29) ... 

Tantalum carbide is produced by carburization of the element or the oxide with carbon, ia a manner similar to the preparation of WC or TiC. Final carburization in a vacuum gives a golden yellow carbide, free of oxygen and nitrogen, that contains 6.1—6.3 wt % C and 0—0.2 wt % graphite. 

The buildup of carbonaceous materials in the sulfuric acid presents one of the most serious problems of acid concentration (76—80). Acid concentration also presents a corrosion problem. The vessels are mild steel lined with lead or brick the steam heating elements are composed of siUcon, iron, or tantalum, and pipelines are generally constmcted of lead (81). 

---