Synthesis of macroinitiators

Block copolymers are synthesised with PSSNa and PMMA macroinitiators as the starting material. 

Prepare a solution of SSNa (23.0 mmol), methyl-4-(bromomethyl) benzoate (initiator I, 0.332 mmol), copper (I) bromide (0.33 mmol) and 2,2 -bipyridine (0.66 mmol) in a methanol/water (50/50) solution in a dry round-bottom flask. Stir the reaction mixture at 25 °C. After 24 h, precipitate the product using tetrahydrofuran and dry under vacuum. 

Add MMA (29.9 mmol), a,a -dibromo-p-xylene (initiator II, 0.60 mmol), copper (I) bromide (1.20 mmol), 2,2 -bipyridine (1.20 mmol) and dimethylformamide (DMF) (solvent) to a dry round-bottom flask. Degas the reaction mixture, flush with argon and stir in an oil bath at 110 C for 24 h. Precipitate the product in water and dry under vacuum. 

Prepare a solution of MM A (9.4 mmol), dimethyl 5-(4-(bromomethyl) benzyloxy) benzene-1,3-dioate (initiator III, 0.187 mmol), copper (I) bromide (0.037 mmol), N,N,N, N ,N -pentamethyldiethylene triamine (PMDETA) (0.0370 mmol) in DMF and keep the reaction mixture in an oil bath at 110 C imder an argon atmosphere. Product recovery is achieved using water. 

---

Initially, the polymerization of macromonomers was achieved by free radical polymerization reactions, which allowed only a limited control of the final properties. With the advent of ROMP and new free radical polymerization techniques, such as atom transfer radical polymerization (ATRP) the control of final properties became more facile (16). ATRP and ROMP techniques can be combined for the synthesis of macroinitiators (17). 

Enzymatic Synthesis of Macroinitiators Followed by Chemical Polymerization... 

Synthetic approaches to azobenzene BCs (a) sequential polymerization synthesis of macroinitiator and subsequent direct polymerization of azomonomers (b) postfunctionalization (c) coupling of preformed blocks. 

The direct synthesis of poly(3-sulfopropyl methacrylate)-fr-PMMA, PSP-MA-fr-PMMA (Scheme 27) without the use of protecting chemistry, by sequential monomer addition and ATRP techniques was achieved [77]. A water/DMF 40/60 mixture was used to ensure the homogeneous polymerization of both monomers. CuCl/bipy was the catalytic system used, leading to quantitative conversion and narrow molecular weight distribution. In another approach the PSPMA macroinitiator was isolated by stopping the polymerization at a conversion of 83%. Then using a 40/60 water/DMF mixture MMA was polymerized to give the desired block copolymer. In this case no residual SPMA monomer was present before the polymerization of MMA. The micellar properties of these amphiphilic copolymers were examined. 

Diblock copolymers PEO-fo-PS have been prepared using PEO macroinitiator and ATRP techniques [125]. The macroinitiator was synthesized by the reaction of monohydroxy-functionalized PEO with 2-chloro-2-phenylacetyl-chloride. MALDI-TOF revealed the successful synthesis of the macroinitiators. The ATRP of styrene was conducted in bulk at 130 °C with CuCl as the catalyst and 2,2 bipyridine, bipy, as the ligand. Yields higher than 80% and rather narrow molecular weight distributions (Mw/Mn < 1.3) were obtained. The surface morphology of these samples was investigated by atomic force microscopy, AFM. 

The triblock terpolymer polypropylene oxide)-h-poly[2-(dimethylami-no)ethyl methacrylate]-b-poly[oligo(ethylene glycol) methacrylate], PPO-fc-PDMAEMA-fc-POEGMA, was prepared using the PPO macroinitiator followed by the addition of CuCl, HMTETA, and DMAEMA for the polymerization of the second block and finally OEGMA for the synthesis of the final product (Scheme 54) [128]. 

A PEO macroinitiator with Si — H end groups was prepared through the condensation of monohydroxy-terminated PEO with CISiMePhH in the presence of pyridine [130]. The presence of the Si —Ph moiety prevents the hydrolysis of the Si — O — C bond, due to steric factors. This macroinitiator was subsequently used for the synthesis of poly(ferrocenyldimethylsilane), PFS, to afford PEO-fc-PFS block copolymers. The ROP of the ferrocenophane was conducted catalytically using the Pt(0) Karstedt s catalyst in toluene at 25 °C (Scheme 55). Rather broad molecular weight distributions (higher than 1.3) were obtained. 

The oxocarbenium perchlorate C(CH20CH2CH2C0+C104 )4 was employed as a tetrafunctional initiator for the synthesis of PTHF 4-arm stars [146]. The living ends were subsequently reacted either with sodium bromoacetate or bromoisobutyryl chloride. The end-capping reaction was not efficient in the first case (lower than 45%). Therefore, the second procedure was the method of choice for the synthesis of the bromoisobutyryl star-shaped macroinitiators. In the presence of CuCl/bpy the ATRP of styrene was initiated in bulk, leading to the formation of (PTHF-fc-PS)4 star-block copolymers. Further addition of MMA provided the (PTHF-fr-PS-fc-PMMA)4 star-block terpolymers. Relatively narrow molecular weight distributions were obtained with this synthetic procedure. 

More recently, the scope of using hyperbranched polymers as soluble supports in catalysis has been extended by the synthesis of amphiphilic star polymers bearing a hyperbranched core and amphiphilic diblock graft arms. This approach is based on previous work, where the authors reported the synthesis of a hyperbranched macroinitiator and its successful application in a cationic grafting-from reaction of 2-methyl-2-oxazoline to obtain water-soluble, amphiphilic star polymers [73]. Based on this approach, Nuyken et al. prepared catalyticaUy active star polymers where the transition metal catalysts are located at the core-shell interface. The synthesis is outlined in Scheme 6.10. 

Block copolymers of (R,S)-(3-butyrolactone and eCL have been synthesized by combining the anionic ROP of the first monomer with the coordinative ROP of the second one (Scheme 15) [71]. The first step consisted of the synthesis of hydroxy-terminated atactic P(3BL by anionic polymerization initiated by the alkali-metal salt of a hydroxycarboxylic acid complexed with a crown ether. The hydroxyl end group of P(3BL could then be reacted with AlEt3 to form a macroinitiator for the eCL ROP. 

In a different approach, Hedrick et al. have studied multifunctional dendritic initiators for the synthesis of multiarm star-shaped copolymers [102]. Several dendritic initiators with hydroxyl functionality ranging from 2 to 48 have been prepared according to the method developed by Hult et al. [120]. The bulk polymerization of sCL initiated by these multifunctional macroinitiators and acti-... 

Fig. 10 Synthesis of the macroinitiator precursor (I), the macroinitiator (II) and macro-molecular gradient brush copolymer (III). (Reproduced with permission from [55])...

Sha et al. applied the commercially available dual initiator ATRP-4 for the chemoenzymatic synthesis of block copolymers. In a first series of publications, the group reported the successful synthesis of a block copolymer comprising PCL and polystyrene (PS) blocks [31, 32]. This concept was then further applied for the chemoenzymatic synthesis of amphiphilic block copolymers by macroinitiation of glycidyl methacrylate (GMA) from the ATRP functional PCL [33]. This procedure yielded well-defined block copolymers, which formed micelles in aqueous solution. Sha et al. were also the first to apply the dual enzyme/ATRP initiator concept to an enzymatic polycondensation of 10-hydroxydecanoic acid [34]. This concept was then extended to the ATRP of GMA and the formation of vesicles from the corresponding block copolymer [35]. 

The second strategy for the chemoenzymatic synthesis of block copolymers from enzymatic macroinitiators employs an individual modification step of the enzymatic block with an initiator for the chemical polymerization (route B in Fig. 4). This strategy has the advantage that it does not depend on a high incorporation rate of the dual initiator. On the other hand, quantitative end-functionalization becomes more... 

Apart from ATRP, the concept of dual initiation was also applied to other (controlled) polymerization techniques. Nitroxide-mediated living free radical polymerization (LFRP) is one example reported by van As et al. and has the advantage that no further metal catalyst is required [43], Employing initiator NMP-1, a PCL macroinitiator was obtained and subsequent polymerization of styrene produced a block copolymer (Scheme 4). With this system, it was for the first time possible to successfully conduct a one-pot chemoenzymatic cascade polymerization from a mixture containing NMP-1, CL, and styrene. Since the activation temperature of NMP is around 100 °C, no radical polymerization will occur at the reaction temperature of the enzymatic ROP. The two reactions could thus be thermally separated by first carrying out the enzymatic polymerization at low temperature and then raising the temperature to around 100 °C to initiate the NMP. Moreover, it was shown that this approach is compatible with the stereoselective polymerization of 4-MeCL for the synthesis of chiral block copolymers. 

Also, Kerep and Ritter reported a radical chain transfer agent as a dual initiator, FRP-1 [45]. The first step builds on the fact that hydroxyl groups are much better nucleophiles in enzymatic ROP than thiols. Due to the chemoselectivity of the enzyme, PCLs with predominantly thiol endgroups were obtained, which were subsequently used as macroinitiator for styrene. The authors report that the reaction yield can be further increased by microwave irradiation. Although thiols provide less control over the radical polymerization than RAFT agents, the subsequent radical polymerization successfully leads to the synthesis of PCL-Z -PS. 

---