Surface science studies

The importance of low pressures has already been stressed as a criterion for surface science studies. However, it is also a limitation because real-world phenomena do not occur in a controlled vacuum. Instead, they occur at atmospheric pressures or higher, often at elevated temperatures, and in conditions of humidity or even contamination. Hence, a major tlmist in surface science has been to modify existmg techniques and equipment to pemiit detailed surface analysis under conditions that are less than ideal. The scamiing tunnelling microscope (STM) is a recent addition to the surface science arsenal and has the capability of providing atomic-scale infomiation at ambient pressures and elevated temperatures. Incredible insight into the nature of surface reactions has been achieved by means of the STM and other in situ teclmiques. 

Surface science studies of corrosion phenomena are excellent examples of in situ characterization of surface reactions. In particular, the investigation of corrosion reactions with STM is promising because not only can it be used to study solid-gas interfaces, but also solid-liquid interfaces. 

The following two sections will focus on epitaxial growth from a surface science perspective with the aim of revealing the fundamentals of tliin-film growth. As will be discussed below, surface science studies of thin-film deposition have contributed greatly to an atomic-level understanding of nucleation and growth. 

Dry etching is a commonly used teclmique for creating highly anisotropic, patterned surfaces. The interaction of gas phase etchants with surfaces is of fundamental interest to understanding such phenomena as undercutting and the dependence of etch rate on surface structure. Many surface science studies aim to understand these interactions at an atomic level, and the next section will explore what is known about the etching of silicon surfaces. 

Surface science studies of catalytic reactions certainly have shed light on the atomic-level view of catalysis. Despite this success, however, two past criticisms of the surface science approach to catalysis are that the... 

The first step consists of the molecular adsorption of CO. The second step is the dissociation of O2 to yield two adsorbed oxygen atoms. The third step is the reaction of an adsorbed CO molecule with an adsorbed oxygen atom to fonn a CO2 molecule that, at room temperature and higher, desorbs upon fomiation. To simplify matters, this desorption step is not included. This sequence of steps depicts a Langmuir-Hinshelwood mechanism, whereby reaction occurs between two adsorbed species (as opposed to an Eley-Rideal mechanism, whereby reaction occurs between one adsorbed species and one gas phase species). The role of surface science studies in fomuilating the CO oxidation mechanism was prominent. 

It is important to realize that the assumption of a rate-determining step limits the scope of our description. As with the steady state approximation, it is not possible to describe transients in the quasi-equilibrium model. In addition, the rate-determining step in the mechanism might shift to a different step if the reaction conditions change, e.g. if the partial pressure of a gas changes markedly. For a surface science study of the reaction A -i- B in an ultrahigh vacuum chamber with a single crystal as the catalyst, the partial pressures of A and B may be so small that the rates of adsorption become smaller than the rate of the surface reaction. 

Computational chemistry has reached a level in which adsorption, dissociation and formation of new bonds can be described with reasonable accuracy. Consequently trends in reactivity patterns can be very well predicted nowadays. Such theoretical studies have had a strong impact in the field of heterogeneous catalysis, particularly because many experimental data are available for comparison from surface science studies (e.g. heats of adsorption, adsorption geometries, vibrational frequencies, activation energies of elementary reaction steps) to validate theoretical predictions. 

D.A. Rudd, L.A. Apuvicio, J.E. Bekoske and A.A. Trevino, The Microkinetics of Heterogeneous Catalysis (1993), American Chemical Society, Washington DC]. Ideally, as many parameters as can be determined by surface science studies of adsorption and of elementary steps, as well as results from computational studies, are used as the input in a kinetic model, so that fitting of parameters, as employed in Section 7.2, can be avoided. We shall use the synthesis of ammonia as a worked example [P. Stoltze and J.K. Norskov, Phys. Rev. Lett. 55 (1985) 2502 J. Catal. 110 (1988) Ij. 

Surface science studies have generated much insight into how hydrocarbons react on the surfaces of platinum single crystals. We refer to Somorjai [G.A. Somor-jai. Introduction to Surface Chemistry and Catalysis (1994), Wiley, New York] for a detailed overview. Also, the reactions of hydrocarbons on acidic sites of alumina or on zeolites have been studied in great detail [H. van Bekkum, E.M. Flanigan and J.C. Jansen (Eds.), Introduction to Zeolite Science and Practice (1991), Elsevier, Amsterdam],... 

CO oxidation and the reaction between CO -t NO have been extensively studied. Much less is known about hydrocarbon oxidation, and the role of hydrocarbons in reducing NO is only beginning to be explored. Surface science studies with reactions on well-defined single-crystal surfaces have contributed significantly to our understanding, for an overview see B.E. Nieuwenhuys, Adv. Catal. 44 (1999) 259. 

The SCR catalyst is considerably more complex than, for example, the metal catalysts we discussed earlier. Also, it is very difficult to perform surface science studies on these oxide surfaces. The nature of the active sites in the SCR catalyst has been probed by temperature-programmed desorption of NO and NH3 and by in situ infrared studies. This has led to a set of kinetic parameters (Tab. 10.7) that can describe NO conversion and NH3 slip (Fig. 10.16). The model gives a good fit to the experimental data over a wide range, is based on the physical reality of the SCR catalyst and its interactions with the reacting gases and is, therefore, preferable to a simple power rate law in which catalysis happens in a black box . Nevertheless, several questions remain unanswered, such as what are the elementary steps and what do the active site looks like on the atomic scale ... 

Markovic NM, Ross PN (2002) Surface science studies of model fuel cell electrocatalysis. Surf Sci Rep 45 117-229... 

As the crystal surface exposed to the atmosphere is usually not ideal, specific sites exist with even much lower co-ordination numbers. This is shown schematically in Fig. 3.5, which gives a model comprising so-called step, kink and terrace sites (Morrison, 1982). This analysis suggests that even pure metal surfaces contain a wide variety of active sites, which indeed has been confirmed by surface science studies. Nevertheless, catalytic surfaces often behave rather homogeneously. Later it will be discussed why this is the case. In short, the most active sites deactivate easiest and the poorest active sites do not contribute much to the catalytic activity, leaving the average activity sites to play the major role. 

Freund s group at the Fritz Flaber Institute have put much emphasis on linking surface science studies with applied catalysts through replicating the latter with model systems without having to resort to the complexity of the real system. A system they have studied in detail is that of nitric oxide chemisorption at a palladium-alumina model catalyst, where they isolated different... 

SURFACE SCIENCE STUDIES OF THE MECHANISM OF NO CONVERSION CORRELATIONS BETWEEN KINETICS IN VACUUM VERSUS UNDER CATALYTIC CONDITIONS... 

Abstract A review is provided on the contribution of modern surface-science studies to the understanding of the kinetics of DeNOx catalytic processes. A brief overview of the knowledge available on the adsorption of the nitrogen oxide reactants, with specific emphasis on NO, is provided first. A presentation of the measurements of NO, reduction kinetics carried out on well-characterized model system and on their implications on practical catalytic processes follows. Focus is placed on isothermal measurements using either molecular beams or atmospheric pressure environments. That discussion is then complemented with a review of the published research on the identification of the key reaction intermediates and on the determination of the nature of the active sites under realistic conditions. The link between surface-science studies and molecular computational modeling such as DFT calculations, and, more generally, the relevance of the studies performed under ultra-high vacuum to more realistic conditions, is also discussed. 

Surface Science Studies of the Mechanism ofNOx Conversion... 

---