Surface modifiers organic amines

Cyanoacrylate adhesives cure by anionic polymerization. This reaction is catalyzed by weak bases (such as water), so the adhesives are generally stabilized by the inclusion of a weak acid in the formulation. While adhesion of cyanoacrylates to bare metals and many polymers is excellent, bonding to polyolefins requires a surface modifying primer. Solutions of chlorinated polyolefin oligomers, fran-sition metal complexes, and organic bases such as tertiary amines can greatly enhance cyanoacrylate adhesion to these surfaces [72]. The solvent is a critical component of these primers, as solvent swelling of the surface facilitates inter-... 

Certain compounds which have the ability to film or adsorb onto a metal surface are effective at improving fuel lubricity performance. These compounds include modified fatty acids, modified fatty amines, and other amine=based compounds. For years, the lubricity performance of jet fuel has been improved by treatment with organic acid based corrosion inhibitors. 

Composites of PANI-NFs, synthesized using a rapid mixing method, with amines have recently been presented as novel materials for phosgene detection [472]. Chemiresistor sensors with nanofibrous PANI films as a sensitive layer, prepared by chemical oxidative polymerization of aniline on Si substrates, which were surface-modified by amino-silane self-assembled monolayers, showed sensitivity to very low concentration (0.5 ppm) of ammonia gas [297]. Ultrafast sensor responses to ammonia gas of the dispersed PANI-CSA nanorods [303] and patterned PANI nanobowl monolayers containing Au nanoparticles [473] have recently been demonstrated. The gas response of the PANI-NTs to a series of chemical vapors such as ammonia, hydrazine, and triethylamine was studied [319,323]. The results indicated that the PANI-NTs show superior performance as chemical sensors. Electrospun isolated PANI-CSA nanofiber sensors of various aliphatic alcohol vapors have been proven to be comparable to or faster than those prepared from PANI-NF mats [474]. An electrochemical method for the detection of ultratrace amount of 2,4,6-trinitrotoluene with synthetic copolypeptide-doped PANI-NFs has recently been reported [475]. PANI-NFs, prepared through the in situ oxidative polymerization method, were used for the detection of aromatic organic compounds [476]. 

Nakayama, N. H ashi, T. Preparation of Ti02 nanoparticles surface-modified by both carboxylic acid and amine Dispersibility and stabilization in organic solvents. Coll. Surf. A, 2008, 317, 543-550. 

Brust, Sebestian, and Halasz (691) modified the surface with organic groups linked through Si-N-C bonds with functional groups in an attached aliphatic chain such as -COOH, -SO,H-NHs, -CN, or -NOs. The SiOH surface is Hrst reacted with SOCli which converts it to SiCl, which then reacts with amines. 

Organically modified clays are mixtures of anthracite and bentonite clay or bulk clay. The surface of the clay is usually activated after treating with a quaternary amine. These clays are employed only in the purification of gas streams. 

Research into chemically modified electrodes has led to a number of new ways to build chemical selectivity into films that can be coated onto electrode surfaces. Perhaps the simplest example is the use of the polymer Nafion (see Table 13.2) to make selective electrodes for basic research in neurophysiology [88]. Starting with the pioneering investigations by Ralph Adams, electrochemists have become interested in the electrochemical detection of a class of amine-based neurotransmitters in living organisms. The quintessential example of this class of neurotransmitters is the molecule dopamine, which can be electrochemically oxidized via the following redox reaction ... 

The lubrication system is extremely complex. The mechanism of lubrication is partly dictated by the nature of interactions between the lubricant and the solid surface. Additives blended into lubricating oil formulations either adsorb onto the sliding surfaces, eg., fatty alcohols, fatty amines, amides, phosphoric acid esters (friction modifiers), or react with the surface, eg., ZDDP, MoDTC, MoDDP organic phosphates (extreme pressure). Some interactions affecting the surfaces of metals include adsorption, chemisorption, and tribochemical reactions-these form new compounds on the surface and lubrication by reaction products (Bhushan and Gupta, 1991 Briscoe et al., 1973 Briscoe and Evens, 1982 Heinicke, 1984 Hsu and Klaus, 1978 and 1979 Klaus and Tewksbury, 1987 Lansdown, 1990 Liston, 1993 McFadden et al., 1998 Studt, 1989). 

---