Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Supplier rating

Supplier Acceptable supplier rating Environmental management system in place and >25% green chemistry preferred ISO 14001 and 75% green chemistry preferred... [Pg.295]

Declining Block Rate - An electricity supplier rate structure in which the per unit price of electricity decreases as the amount of energy increases. Normally only available to very large consumers. [Pg.331]

Usually the supplier development program involves only key suppliers and may actually start with just those suppliers who volunteer. When the supplier starts in the program, it will start to receive regular supplier ratings. If a supplier rating is negative, or if the purchaser rejects material, the supplier is entered into the corrective action stage. This requires the supplier to develop an... [Pg.160]

Suppliers rated the effort as good to excellent, particularly in view of the shared savings. [Pg.181]

Suppliers process equipment and rates higher capacity units may be available. SO concentration includes sum of initial reaction gas plus equalizer diluent air. Nominal reaction gas velocity calculated in absence of organics. [Pg.87]

Membrane Characterization Membranes are always rated for flux and rejection. NaCl is always used as one measure of rejection, and for a veiy good RO membrane, it will be 99.7 percent or more. Nanofiltration membranes are also tested on a larger solute, commonly MgS04. Test results are veiy much a function of how the test is run, and membrane suppliers are usually specific on the test conditions. Salt concentration will be specified as some average of feed and exit concentration, but both are bulk values. Salt concentration at the membrane governs performance. Flux, pressure, membrane geome-tiy, and cross-flow velocity all influence polarization and the other variables shown in Fig. 22-63. [Pg.2035]

The expander train supplier shall assist with the selection of the expander inlet and bypass valve configurations and closure rates by performing an open loop dynamic simulation study. For a main air blower train dais could be closed loop. [Pg.319]

PROJECT UNIT APPUCATION P1(PSIA) T2 ( F) Rated kW LOCATION START-UP DATE AMB SUPPLIER AMB SYSTEM... [Pg.354]

For each q and q risk value and the Severity Rating (S), a level of design acceptability is determined from where these values intersect on the Conformability Map. The symbols, relating to the levels of design acceptability, are then placed in the nodes of the Conformability Matrix for each variability risk which the failure mode is directly dependent on for the failure to occur. Once the level of design acceptability has been determined, it can then be written on the Conformability Matrix in the Comments section. Cpi values predicted or comments for suppliers can be added too, although predicted Cp values can also be written in the variability risks results table. [Pg.86]

E 7) r — S. i E Garnpcrcrij 3SS-c-nMv Failufe Descriptt n FMEA Severity Rating CS) Con-irner its jnciLcdlrig action Tor suppliers)... [Pg.87]

Conduet quality improvement programmes as required Create and utilize supplier quality ratings. [Pg.273]

The suppliers of nylon 46 have laid particular emphasis on the fact that this polymer, with its highly symmetrical chain structure, leads to both a high level of crystallinity and a high rate of nucleation. In turn the high nucleation rate leads to a fine crystalline structure which in this case is claimed to lead to a higher impact strength (dry as moulded) than with nylons 6 and 66. [Pg.489]

If the efficiency estimate is based on published data for similar processes or on equipment supplier s literature, or if you otherwise estimated either the influent or effluent waste comparison or the flow rate, chock "No."... [Pg.49]

While not measurable, these subjective terms enable customers to rate products and services on the extent to which they satisfy their requirements and are therefore suitable for their purpose. However, to the company supplying products and services, a more precise means of measuring quality is needed. To the supplier, a quality product is one that meets in full the perceived customer requirements. [Pg.24]

Subcontractor/supplier performance will be evident from audit reports, surveillance visit reports, and receipt inspections carried out by you or the third party if one has been employed. You need to examine these documents for evidence that the subcontractor s quality system is controlling the quality of the products and services supplied. You can determine the effectiveness of these controls by periodic review of the subcontractor s performance what some firms call vendor rating . By collecting data on the performance of subcontractors/suppliers over a long period you can measure their effectiveness and rate them on a scale from excellent to poor. In such cases you should measure at least three characteristics quality, delivery, and service. Quality would be measured by the ratio of defective conforming products received delivery would be measured by the number of days early or late and service would be measured by the responsiveness to actions requested by you on scale of excellent to poor. The output of these reviews should be in the form of updates to the list of assessed subcontractors/suppliers. [Pg.323]

Toxicity classification is based on recommended exposure limits provided by chemical suppliers. This rating is provisional and will be reviewed when toxicological testing is completed. [Pg.315]

Type of sw gear Supplier Type reference System voltage System freq y Fault ratings... [Pg.190]


See other pages where Supplier rating is mentioned: [Pg.298]    [Pg.136]    [Pg.22]    [Pg.162]    [Pg.162]    [Pg.163]    [Pg.67]    [Pg.503]    [Pg.220]    [Pg.298]    [Pg.136]    [Pg.22]    [Pg.162]    [Pg.162]    [Pg.163]    [Pg.67]    [Pg.503]    [Pg.220]    [Pg.98]    [Pg.774]    [Pg.790]    [Pg.796]    [Pg.970]    [Pg.1650]    [Pg.2226]    [Pg.160]    [Pg.89]    [Pg.91]    [Pg.96]    [Pg.97]    [Pg.102]    [Pg.105]    [Pg.485]    [Pg.487]    [Pg.232]    [Pg.200]    [Pg.509]    [Pg.38]    [Pg.323]    [Pg.839]    [Pg.1004]    [Pg.317]   
See also in sourсe #XX -- [ Pg.51 ]




SEARCH



© 2024 chempedia.info