Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Sulfuric acid aqueous solution properties

Although Cr03 is soluble in some organic solvents, like tert-butyl alcohol, pyridine or acetic anhydride, its use in such solvents is limited, because of the tendency of the resulting solutions to explode.2,3 Nevertheless, acetone can safely be mixed with a solution of chromium trioxide in diluted aqueous sulfuric acid. This useful property prompted the development of the so-called Jones oxidation, in which a solution of chromium trioxide in diluted sulfuric acid is dropped on a solution of an organic compound in acetone. This reaction, first described by Jones,13 has become one of the most employed procedures for the oxidation of alcohols, and represents a seminal contribution that prompted the development of other chromium (VI) oxidants in organic synthesis. [Pg.1]

Alkanes can be oxidized in the presence of some transition metal complexes in aqueous and acidic media For example, in concentrated sulfuric acid the oxidative properties of the complexes are enhanced. Solutions of derivatives of palladium(II), platinum(III), manganese(III) and mercury(II) as well as some other compounds (hydrogen peroxide, ammonium persulfate, nitric acid and even concentrated sulfuric acid itself) can be used as oxidants. In the cases of metal-free oxidants the active species are apparently electrophiles such as NO2 or SO3I-C (for nitration of aromatics, see, for example, recent publication [40] and references therein). [Pg.335]

Niobic Acid. Niobic acid, Nb20 XH2O, includes all hydrated forms of niobium pentoxide, where the degree of hydration depends on the method of preparation, age, etc. It is a white insoluble precipitate formed by acid hydrolysis of niobates that are prepared by alkaH pyrosulfate, carbonate, or hydroxide fusion base hydrolysis of niobium fluoride solutions or aqueous hydrolysis of chlorides or bromides. When it is formed in the presence of tannin, a volurninous red complex forms. Freshly precipitated niobic acid usually is coUoidal and is peptized by water washing, thus it is difficult to free from traces of electrolyte. Its properties vary with age and reactivity is noticeably diminished on standing for even a few days. It is soluble in concentrated hydrochloric and sulfuric acids but is reprecipitated on dilution and boiling and can be complexed when it is freshly made with oxaHc or tartaric acid. It is soluble in hydrofluoric acid of any concentration. [Pg.28]

Table 7.2 Partial molar thermal properties for aqueous sulfuric acid solutions at T = 298.15 K. m is the molality of the H1SO4 and A is the ratio (moles FFO/moles... Table 7.2 Partial molar thermal properties for aqueous sulfuric acid solutions at T = 298.15 K. m is the molality of the H1SO4 and A is the ratio (moles FFO/moles...
Values taken from S. Glasstone. Thermodynamics for Chemists. D. Van Nostrand Company Inc., Toronto, p. 443 (1947). The values tabulated in this reference were taken from D. N. Craig and G. W. Vinal, J. Res. Natl. Bur. Stand.. Thermodynamic Properties of Sulfuric Acid Solutions and Their Relation to the Electromotive Force and Heat of Reaction of the Lead Storage Battery", 24, 475-490 (1940). More recent values at the higher molality can be found in W. F. Giauque. E. W. Hornung. J. E. Kunzler and T. R. Rubin, The Thermodynamic Properties of Aqueous Sulfuric Acid Solutions and Hydrates from 15 to 300° K", J. Am. Chem. Soc.. 82, 62-70 (1960). [Pg.382]

Acidification of chloramine T with sulfuric acid produces the formation of dichloramine T (DCT) and hypochlorous acid (HCIO), species which react with C=C bonds of the butadiene units. The effectiveness of the treatment is ascribed to the introduction of chlorine and oxygen moieties on the mbber surface. A decrease in the pH of the chloramine T aqueous solutions produced more extended surface modifications and improved adhesion properties in the joints produced with waterborne polyurethane adhesive (Figure 27.9). The adhesive strength obtained is slightly lower than that obtained for the rubber treated with 3 wt% TCI/MEK, and its increases as the pH of the chloramine T solution decreases (Figure 27.9). A cohesive failure in the rubber is generally obtained. [Pg.769]

Takasu Y, Eujii Y, Yasuda K, Iwanaga Y, Matsuda Y. 1989. Electrocatalytic properties of ultra-fine platinum particles for hydrogen electrode reaction in an aqueous solution of sulfuric acid. Electrochim Acta 34 453-458. [Pg.564]

Oxadiazoles are weak Hammett bases. The basicity constants of 2,5-diphenyl-1,3,4-oxadiazole (pK -2.49) and of 2-(4-methylphenyl)-5-phenyl-l,3,4-oxadiazole (pAa -1.15) were measured by the method of Yates and MacClelland in an aqueous solution of sulfuric acid in the range from pH 7 to H0 -10. Both compounds exhibited luminescence properties depending on the acid concentration <1996SAA1875>. [Pg.409]

Rubidium acid salts are usually prepared from rubidium carbonate or hydroxide and the appropriate acid in aqueous solution, followed by precipitation of the crystals or evaporation to dryness. Rubidium sulfate is also prepared by the addition of a hot solution of barium hydroxide to a boiling solution of rubidium alum until all the aluminum is precipitated. The pH of the solution is 7.6 when the reaction is complete. Aluminum hydroxide and barium sulfate are removed by filtration, and rubidium sulfate is obtained by concentration and crystallization from the filtrate. Rubidium aluminum sulfate dodecahydrate [7488-54-2] (alum), RbA SO 12H20, is formed by sulfuric acid leaching of lepidolite ore. Rubidium alum is more soluble than cesium alum and less soluble than the other alkali alums. Fractional crystallization of Rb alum removes K, Na, and Li values, but concentrates the cesium value. Rubidium hydroxide, RbOH, is prepared by the reaction of rubidium sulfate and barium hydroxide in solution. The insoluble barium sulfate is removed by filtration. The solution of rubidium hydroxide can be evaporated partially in pure nickel or silver containers. Rubidium hydroxide is usually supplied as a 50% aqueous solution. Rubidium carbonate, Rb2C03, is readily formed by bubbling carbon dioxide through a solution of rubidium hydroxide, followed by evaporation to dryness in a fluorocarbon container. Other rubidium compounds can be formed in the laboratory by means of anion-exchange techniques. Table 4 lists some properties of common rubidium compounds. [Pg.280]

An interesting group of composite membranes with very good properties is produced by condensation of furfuryl alcohol with sulfuric acid. The first membrane of this type was made by Cadotte at North Star Research and was known as the NS200 membrane [32], These membranes are not made by the interfacial composite process rather a polysulfone microporous support membrane is contacted first with an aqueous solution of furfuryl alcohol and then with sulfuric acid. The coated support is then heated to 140 °C. The furfuryl alcohol forms a polymerized, crosslinked layer on the polysulfone support the membrane is completely black. The chemistry of condensation and reaction is complex, but a possible polymerization scheme is shown in Figure 5.10. [Pg.204]

Re has recently come to the forefront in liquid phase oxidation catalysis, mainly as a result of the discovery of the catalytic properties of the alkyl compound CH3Re03 [methyltrioxorhenium (MTO)]. MTO forms mono-and diperoxo adducts with H2O2 these species are capable of transferring an oxygen atom to almost any nucleophile, including olefins, allylic alcohols, sulfur compounds, amides, and halide ions (9). Moreover, MTO catalysis can be accelerated by coordination of N ligands such as pyridine (379-381). An additional effect of such bases is that they buffer the strong Lewis acidity of MTO in aqueous solutions and therefore protect epoxides, for example. [Pg.67]

Sulfur dioxide is quite soluble in water such solutions, which possess acidic properties, have long been referred to as solutions of sulfurous acid (H2S03). However, H2S03 either is not present or is present only in infinitesimal quantities in such solutions. The so-called hydrate H2S03- 6H20 is really a gas hydrate S02—7H20. The equilibria in aqueous solutions of S02 are best represented as... [Pg.526]


See other pages where Sulfuric acid aqueous solution properties is mentioned: [Pg.465]    [Pg.523]    [Pg.465]    [Pg.523]    [Pg.344]    [Pg.308]    [Pg.356]    [Pg.280]    [Pg.454]    [Pg.515]    [Pg.246]    [Pg.353]    [Pg.98]    [Pg.853]    [Pg.111]    [Pg.108]    [Pg.110]    [Pg.140]    [Pg.249]    [Pg.184]    [Pg.10]    [Pg.13]    [Pg.309]    [Pg.308]    [Pg.269]    [Pg.635]    [Pg.223]    [Pg.218]    [Pg.635]    [Pg.467]    [Pg.159]    [Pg.236]    [Pg.360]    [Pg.217]    [Pg.146]    [Pg.279]    [Pg.526]    [Pg.315]    [Pg.839]    [Pg.1265]    [Pg.281]   
See also in sourсe #XX -- [ Pg.464 , Pg.465 , Pg.466 , Pg.467 ]




SEARCH



Aqueous acid solution

Aqueous acidic solutions

Aqueous properties

Aqueous solution acidic solutions

Aqueous solution properties

Solute property

Solution properties

Solution, sulfuric acid properties

Sulfur properties

Sulfuric acid properties

Sulfuric acid solutions

Sulfuric acid, aqueous solutions

© 2024 chempedia.info