Sulfite reaction with

Mechanical and Chemical Deaeration. The corrosive quahties of water can he reduced by deaeration. Vacuum deaeration has been used successftdly in once-through cooling systems. When all oxygen is not removed, catalyzed sodium sulfite can be used to remove the remaining oxygen. The sulfite reaction with dissolved oxygen is... 

Sulfite Reaction with Methyl Green 0.05-25 Fixed-time procedure, absorbance measurement at 625 nm... 

The higjily water-soluble dienophiles 2.4f and2.4g have been synthesised as outlined in Scheme 2.5. Both compounds were prepared from p-(bromomethyl)benzaldehyde (2.8) which was synthesised by reducing p-(bromomethyl)benzonitrile (2.7) with diisobutyl aluminium hydride following a literature procedure2.4f was obtained in two steps by conversion of 2.8 to the corresponding sodium sulfonate (2.9), followed by an aldol reaction with 2-acetylpyridine. In the preparation of 2.4g the sequence of steps had to be reversed Here, the aldol condensation of 2.8 with 2-acetylpyridine was followed by nucleophilic substitution of the bromide of 2.10 by trimethylamine. Attempts to prepare 2.4f from 2.10 by treatment with sodium sulfite failed, due to decomposition of 2.10 under the conditions required for the substitution by sulfite anion. 

The reaction with sodium sulfite or bisulfite (5,11) to yield sodium-P-sulfopropionamide [19298-89-6] (C3H7N04S-Na) is very useful since it can be used as a scavenger for acrylamide monomer. The reaction proceeds very rapidly even at room temperature, and the product has low toxicity. Reactions with phosphines and phosphine oxides have been studied (12), and the products are potentially useful because of thek fire retardant properties. Reactions with sulfide and dithiocarbamates proceed readily but have no appHcations (5). However, the reaction with mercaptide ions has been used for analytical purposes (13)). Water reacts with the amide group (5) to form hydrolysis products, and other hydroxy compounds, such as alcohols and phenols, react readily to form ether compounds. Primary aUphatic alcohols are the most reactive and the reactions are compHcated by partial hydrolysis of the amide groups by any water present. 

Polythiodipropionic acids and their esters are prepared from acryUc acid or an acrylate with sulfur, hydrogen sulfide, and ammonium polysulfide (32). These polythio compounds are converted to the dithio analogs by reaction with an inorganic sulfite or cyanide. 

By the Bucherer reaction (with sulfite) of the appropriate arninonaphthalenesulfonic acid. 

Chemical recovery ia sodium-based sulfite pulpiag is more complicated, and a large number of processes have been proposed. The most common process iavolves liquor iaciaeration under reduciag conditions to give a smelt, which is dissolved to produce a kraft-type green liquor. Sulfide is stripped from the liquor as H2S after the pH is lowered by CO2. The H2S is oxidized to sulfur ia a separate stream by reaction with SO2, and the sulfur is subsequendy burned to reform SO2. Alternatively, ia a pyrolysis process such as SCA-Bidemd, the H2S gas is burned direcdy to SO2. A rather novel approach is the Sonoco process, ia which alumina is added to the spent liquors which are then burned ia a kiln to form sodium aluminate. In anther method, used particulady ia neutral sulfite semichemical processes, fluidized-bed combustion is employed to give a mixture of sodium carbonate and sodium sulfate, which can be sold to kraft mills as makeup chemical. 

The reactions of thionyl chloride with organic compounds having hydroxyl groups are important. Alkyl chlorides, alkyl sulfites, or alkyl chlorosulfites form from its reaction with aUphatic alcohols, depending on reaction conditions, stoichiometry, and the alcohol stmcture ... 

These three methods are employed commercially. In addition, decomposition of polythionates in alkaline solution or their reaction with sulfide or sulfite gives thiosulfates ... 

Because of the time and expense involved, biological assays are used primarily for research purposes. The first chemical method for assaying L-ascorbic acid was the titration with 2,6-dichlorophenolindophenol solution (76). This method is not appHcable in the presence of a variety of interfering substances, eg, reduced metal ions, sulfites, tannins, or colored dyes. This 2,6-dichlorophenolindophenol method and other chemical and physiochemical methods are based on the reducing character of L-ascorbic acid (77). Colorimetric reactions with metal ions as weU as other redox systems, eg, potassium hexacyanoferrate(III), methylene blue, chloramine, etc, have been used for the assay, but they are unspecific because of interferences from a large number of reducing substances contained in foods and natural products (78). These methods have been used extensively in fish research (79). A specific photometric method for the assay of vitamin C in biological samples is based on the oxidation of ascorbic acid to dehydroascorbic acid with 2,4-dinitrophenylhydrazine (80). In the microfluorometric method, ascorbic acid is oxidized to dehydroascorbic acid in the presence of charcoal. The oxidized form is reacted with o-phenylenediamine to produce a fluorescent compound that is detected with an excitation maximum of ca 350 nm and an emission maximum of ca 430 nm (81). 

The rate of reaction with sulfite is ca 100 times faster than the rate of reaction with hydroxide, and decreasing the Brooker basicity of the acidic nucleus in the merocarbocyanine increases the rate of reaction. 

It is often advantageous to proceed to a desired product through two nucleophilic displacements rather than directly when one can exploit a difference in the reactivity of two leaving groups. An example is the conversion of 4-chloro-2,6-dimethoxypyrimidine (109) (not satisfactorily reactive with sulfanilamide anion) by means of trimethylamine into the more reactive trimethylammonio derivative 110. Conversion of chloro-quinohnes and -pyrimi-dines into nitriles is best accomplished by conversion (with sulfite) into the sulfonic acids before reaction with cyanide. 

At FW temperatures and without a catalyst, the sodium sulfite reaction is only 50% complete after 45 seconds, but this rate increases to 100% complete after 10 seconds with cobalt sulfate. 

Z)-compounds are formed in reactions with hydroxide, methoxide, cyanide, and sulfite ions, whereas (ii)-compounds are formed in most reactions with amines (formation of triazenes) and with diazo coupling components such as phenols and aromatic tertiary amines. 

Elemental sulfur dissolves in boiling aqueous sodium sulfite solutions with the formation of sodium thiosulfate (Na2S203). The reaction proceeds quantitatively if sulfur and excess sodium sulfite are boiled for some time in weakly alkaline solutions. In the cold, however, practically no reaction occurs. Alternatively, thiosulfate can be produced quantitatively in solution phase by using organic solvents to first dissolve sulfur and then accomplish the reaction with aqueous sulfite. In a parallel reaction, elemental selenium dissolves in alkaline sulfite solution to produce selenosulfate, SeSO ... 

Mikolajczyk and coworkers have summarized other methods which lead to the desired sulfmate esters These are asymmetric oxidation of sulfenamides, kinetic resolution of racemic sulfmates in transesterification with chiral alcohols, kinetic resolution of racemic sulfinates upon treatment with chiral Grignard reagents, optical resolution via cyclodextrin complexes, and esterification of sulfinyl chlorides with chiral alcohols in the presence of optically active amines. None of these methods is very satisfactory since the esters produced are of low enantiomeric purity. However, the reaction of dialkyl sulfites (33) with t-butylmagnesium chloride in the presence of quinine gave the corresponding methyl, ethyl, n-propyl, isopropyl and n-butyl 2,2-dimethylpropane-l-yl sulfinates (34) of 43 to 73% enantiomeric purity in 50 to 84% yield. This made available sulfinate esters for the synthesis of t-butyl sulfoxides (35). 

Reaction with the hindered secondary alcohol menthol stops at the dialkyl sulfite ester. The examples reported do not establish the stereochemistry of the reaction. 

Many of the modifications of the pyrazolone antiinflammatory agents are intended to increase the limited hydrophilicity of the parent molecules. Reaction of aminopyrine (157) with formaldehyde and sodium hydrogen sulfite affords dipyrone (158). The first step can be rationalized as an Eschweiler-Clark type N-methylation reaction, with bisulfite acting as the reducing agent. The resulting mono N-methyl analogue of 157 then apparently forms the sulfite adduct of the carbinolamine of formaldehyde. 

Reaction of the spirocyclic imidazoline 316 with glyoxal and sodium hydrogen sulfite results in hydrolysis of the aminal and subsequent double condensation to give the tetrazolopyridopyrazine 317 (Equation 109) <1999JHC117>. The pyridopyridazinylhydrazine 318 can be cyclized to the fused triazole 319 by reaction with formic acid (Equation 110) <1998SC2871>. 

Sulfur also reacts by undergoing addition reactions with several types of species. For example, thiosulfates are produced by the reaction of sulfur with sulfites. 

Sulfur dioxide is an economically important gas that is used as a refrigerant, disinfectant, and reducing atmosphere for preserving food. Although it is also used in the manufacture of many other sulfur compounds, the most important use of S02 is as a precursor in producing sulfuric acid. It can be obtained by burning sulfur, but it is also produced in numerous other reactions. Sulfites react with acids by liberating so2. 

---