Specification data sheet

Printed on the next page is a flame arrester specification (data) sheet dial is a composite of data sheets from several flame arrester mannfactnr-ers and CPI companies. Most flame arrester mannfactnrers have their own data sheets, which can be used with addidonal data added as die user deems necessary. 

The type of driver will be specified by the purchaser. The driver shall be sized to meet the maximum specified operating conditions, including bearing, mechanical seal, external gear, and coupling losses, as applicable, and shall be in accordance with the applicable specifications, as stated in the inquiry specification, data sheets, and order. The driver shall be suitable for satisfactory operation under the utility and site conditions specified. 

Describe the detailed procedure to be followed to check the calibration of the instrument over its certified operating range and process failure limits (to ensure that it is within the tolerances specified in the manufacturer instruction manual and aligns with the requirements specified in the respective instrument specification/data sheet). 

Instrament schedule Instrament specification/data sheets Cable block diagrams Cable schedule Pneumatic tubing schedules Termination drawings Miscellaneous label schedules Field panel specification and drawings Field junction box drawings... 

Factory calibration should be carried out against the instrument specification/data sheets supplied. The calibration activities should address the following areas, as applicable ... 

Instrument specification/data sheet number Tag number Model number... 

Material certificates are normally only required where the materials of construction were specified on the instrument specification/data sheets to comply with process or environmental requirements (e.g., valve bodies and trims). 

The data plate on the instrument must be checked for agreement with the information contained in the appropriate instrument specification/data sheet. 

Inspect the loop and set air/electrical supplies where appropriate. Check in particular that control valve air supply pressures are set in accordance with the instrument specification/data sheet. 

Instrament schedule Instrament specification/data sheets Cable schedules Pneumatic tubing schedules... 

Process design drawing number (P ID, ELD, ULD, etc.) Specification/data sheet number... 

Estimated route length and route identification, if possible Cable specification/data sheet number Identification of special circuits (e.g., IS circuits)... 

Preece, P., Ingersoll, T., Tong, J. Specification (data) sheets - picture a database. In Proceedings of the European Symposium on Computer Aided Process Engineering - ESCAPE 4, pp. 467-474 (1994)... 

Different commonly used compression characterization methods have been demonstrated the Brazilian test, the confined uniaxial and unconfined compression test, and the flexible boundary cubical triaxial test. The HHP method appears as a new and promising possibility within the traditional compression methods. In HHP, higher pressure gives higher bulk density however, beyond a critical given pressure, the final compressed bulk density remains constant (ultimate bulk density). Further studies will determine whether this concept can be included as a quality descriptor in the specification data sheets of commercial food agglomerates. 

Currently there is no complete data base on by-products and impurities. Although EPA s Cincinnati Research Laboratory Organic Chemical Producers Data Base contains some by-product information on 500 chemicals, such information is best found in Product Specifications data sheets available from manufacturers. 

The engineering task that initiates the procurement process is the defining of what has to be procured, by means of specifications, data sheets, drawings, and work-execution plans, and this definition has to be geared towards the capabilities of the suppliers, based on a considered strategy and a knowledge of the marketplace. There remains the work of ... 

Segregation indices have been reported for a number of available microstructured mixers (Table 3.1) [57, 8,9]. However, so far it has not been common to provide this information in specification data sheets for microreactors. The determination of Xg is well described but often the results vary depending on the experimenter. Therefore, it is not always advisable to compare results from different sources. 

The design and fabrication must not violate aity statutory regulations, and should be as per international industrial codes and standards (e.g. ASME Sec VIII, JIS, IBR, etc.) followed by latest amendments unless a different specification is mentioned in the relevant equipment specification data sheet. The offer shall be made on this basis. 

In case of any discrepancy/conflict between requisition and its associated specifications, data sheets and the codes, standards and regulations, the vendor should bring the matter to the purchaser s attention for resolution. 

Mole and mass fractions are appropriate to either the mixture or the solution point of view. The other quantities are appropriate to the solution point of view only. Conversions among these quantities can be carried out using the equations given in Table I-l following this Introduction. Other useful quantities will be defined in the prefaces to individual volumes or on specific data sheets. 

---