Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Special Binary Mixtures

This chapter covers special fractional distillation systems for binary mixtures. The examples illustrate the flexibility of the fractional distillation process and the broad applicability of the design methods. The first section will consider operating conditions that lead to unusual operating lines, and the last section will consider the separation of binary azeotropic mixtures. [Pg.192]

In the cases considered in Chap. 7, it was assumed that there was a net withdrawal at the top of the column equal to Z , but it may be that material is also added to the section such that R is positive, zero, or negative. If R is positive, On+i/Vn will be less than 1.0 if 7 = 0, On+i/Vn will equal 1.0 if R is negative, On+i/Vn will be greater than 1.0. In these cases Xr may be positive or negative. The following example will illustrate this case. [Pg.192]

Leaky Condenser Example. An old ethyl alcohol distillation column has been tested, and it is concluded that there is a leak into the condensate in the condenser that amounts to 6 mols of water per 100 mole of feed. The tower is operating on a feed containing 3.5 mol per cent ethanol and 96.5 mol per cent water and produces [Pg.192]

Solution, As a basis take 100 mols of feed. Then, by over-all material balance, [Pg.193]

Since Fn = On+i, this line intersects the y — x line at a and is parallel to the diagonal. With F Vm, this line will intersect the lower operating line at the usual value, f.e., at re = 0.035. [Pg.193]


The creatmenc of the boundary conditions given here ts a generali2a-tion to multicomponent mixtures of a result originally obtained for a binary mixture by Kramers and Kistecnaker (25].These authors also obtained results equivalent to the binary special case of our equations (4.21) and (4.25), and integrated their equations to calculate the p.ressure drop which accompanies equimolar counterdiffusion in a capillary. Their results, and the important accompanying experimental measurements, will be discussed in Chapter 6 ... [Pg.33]

It is easy to see that reactions must be accompanied by pressure gradients in all but rather special cases. Consider for example, a reaction in a binary mixture. Then there is just one stoichiOTietric relation... [Pg.128]

As a particular case of this result, it follows that the stoichiometric relations are always satisfied in a binary mixture at the limit of bulk diffusion control and Infinite permeability (at least to the extent that the dusty gas equations are valid), since then all the binary pair bulk diffusion coefficients are necessarily equal, as there is only one of them. This special case was discussed by Hite and Jackson [77], and the reasoning set out here is a straightforward generalization of their treatment. [Pg.149]

The special appeal of this approach is that it allows the heat of mixing to be estimated in terms of a single parameter assigned to each component. This considerably simplifies the characterization of mixing, since m components (with m 6 values) can be combined into m(m - l)/2 binary mixtures, so a considerable data reduction follows from tabulating 6 s instead of AH s. Table 8.2 is a list of CED and 6 values for several common solvents, as well as estimated 6 values for several common polymers. [Pg.526]

A very useful special case is that of a binary mixture ... [Pg.362]

Bonded phases are the most useful types of stationary phase in LC and have a very broad range of application. Of the bonded phases, the reverse phase is by far the most widely used and has been applied successfully to an extensive range of solute types. The reverse phases are commonly used with mobile phases consisting of acetonitrile and water, methanol and water, mixtures of both acetonitrile and methanol and water, and finally under very special circumstances tetrahydrofuran may also be added. Nevertheless, the majority of separations can be accomplished using simple binary mixtures. [Pg.81]

However, in some special cases, the lost of information due to the thresholding procedure may cause a noticeable systematic error, because each lattice point such that < )(r) > < )0 contributes the same volume fraction 1/L3 regardless of the field magnitude. Consider an asymmetric binary mixture undergoing the phase separation. The local volume fraction distribution P(< >) has maxima at the equilibrium volume fractions, 1, and is asymmetric relatively to... [Pg.204]

First a derivative is given of the equations of change for a pure fluid. Then the equations of change for a multicomponent fluid mixture are given (without proof), and a discussion is given of the range of applicability of these equations. Next the basic equations for a multicomponent mixture are specialized for binary mixtures, which are then discussed in considerably more detail. Finally diffusion processes in multicomponent systems, turbulent systems, multiphase systems, and systems with convection are discussed briefly. [Pg.159]

Separate drums should be used for the preparation of these binary mixtures. Special care must be taken to ensure that the container for the sulphur mixture is properly sealed, otherwise the sulphur which has been finely milled and heated on milling may oxidize and even ignite in contact with air. [Pg.348]

There is a large body of experimental work on ternary systems of the type salt + water + organic cosolvent. In many cases the binary water + organic solvent subsystems show reentrant phase transitions, which means that there is more than one critical point. Well-known examples are closed miscibility loops that possess both a LCST and a UCST. Addition of salts may lead to an expansion or shrinking of these loops, or may even generate a loop in a completely miscible binary mixture. By judicious choice of the salt concentration, one can then achieve very special critical states, where two or even more critical points coincide [90, 160,161]. This leads to very peculiar critical behavior—for example, a doubling of the critical exponent y. We shall not discuss these aspects here in detail, but refer to a comprehensive review of reentrant phase transitions [90], We note, however, that for reentrant phase transitions one has to redefine the reduced temperature T, because near a given critical point the system s behavior is also affected by the existence of the second critical point. An improper treatment of these issues will obscure results on criticality. [Pg.25]

Here is the (diffusive) mass flux of species A (mass transfer by diffusion per unit time and per unit area normal to the direction of mass transfer, in kg/s m ) and is the (diffusive) molar flux (in kmol/s m ). The mass flux of a species at a location is propoitional to the density of the mixture at that location. Note that p = Px + Pb density and C = Q + is the molar concentration of the binary mixture, and in general, they may vary throughout the mixture. Therefore, pd(pjp) dp or Cd(C /C) + dC - But in the special case of constant mixture density p or constant molar concentration C, the relations above simplify to... [Pg.793]

Phase equilibrium data have been measured for many binary mixtures with a special apparatus and are available in compiled form. These McCabe Thiele diagrams show the mole fraction of volatiles in the liquid phase in relation to the mole fraction of volatiles in the vapour phase in equilibrium at constant pressure [21, 22]. [Pg.74]

In order to analyze multicomponent diffusion processes we must be able to solve the continuity equations (Eq. 1.3.9) together with constitutive equations for the diffusion process and the appropriate boundary conditions. A great many problems involving diffusion in binary mixtures have been solved. These solutions may be found in standard textbooks, as well as in specialized books, such as those by Crank (1975) and Carslaw and Jaeger (1959). [Pg.95]

Parameter will henceforth be referred to as the asymmetry of the model mixture, where xb > 1 characterizes a binary mixture in which the formation of B-B pairs is energetically favored, whereas for XB < L this is the case for A-A pairs. For the special case xb 1 the asymmetric mixture degenerates to the symmetric case previously studied in Refs. [84] and [85]. In addition, we define the selectivity of the solid surfaces by specifying Xs in Eq. (4.125d) in a fashion similar to xb in Eq. (4.125c). Hence, the parameter space of our model is spanned by the set , aBi s, Xb> X s -... [Pg.148]


See other pages where Special Binary Mixtures is mentioned: [Pg.192]    [Pg.193]    [Pg.195]    [Pg.197]    [Pg.199]    [Pg.201]    [Pg.203]    [Pg.205]    [Pg.207]    [Pg.209]    [Pg.211]    [Pg.213]    [Pg.192]    [Pg.193]    [Pg.195]    [Pg.197]    [Pg.199]    [Pg.201]    [Pg.203]    [Pg.205]    [Pg.207]    [Pg.209]    [Pg.211]    [Pg.213]    [Pg.44]    [Pg.44]    [Pg.110]    [Pg.201]    [Pg.388]    [Pg.765]    [Pg.433]    [Pg.193]    [Pg.665]    [Pg.141]    [Pg.375]    [Pg.356]    [Pg.225]    [Pg.487]    [Pg.62]    [Pg.106]    [Pg.62]    [Pg.589]    [Pg.962]    [Pg.413]    [Pg.133]    [Pg.937]    [Pg.7]    [Pg.153]   


SEARCH



Binary mixture

© 2026 chempedia.info