Solute chemical potential measurement

The chemical potentials measured so far do not allow the formulation of thermodynamic criteria for the formation of lyotropic mesophases. Some qualitative remarks, however, can be made. Of particular interest are Ekwall s studies of the relations between the water binding of the mesophases, their ionization, x-ray parameters, and vapor pressures (4). For common soaps at room temperature mesophases can be observed only in the presence of amounts of water that hydrate the ionic and polar groups. Hydration is therefore characteristic of aqueous lyotropic mesophases as well as micellar systems (1, 2, 3). The binding of counterions to the micelles and to the mesoaggregates seems to be of a similar electrostatic nature. The addition of NaCl greatly affects the lamellar phase D and, to a lesser extent, phase E in these phases the counterions are more strongly bound than by micelles in the solution... 

Considering the rather large amount of data required to implement virial methods even at 25°C (e.g., Tables 7.4-7.7), it is tempting to dismiss the methods as no more than statistical fits to experimental data. In fact, however, virial methods take chemical potentials measured from simple solutions containing just one or two salts to provide an activity model capable of accurately predicting species activities in complex fluids. Eugster et al. (1980), for example, used the virial method of Harvie and Weare (1980) to accurately trace the evaporation of seawater almost to the point of desiccation. Using any other activity model, such a calculation could not even be contemplated. Other... 

For precise measurements, diere is a slight correction for the effect of the slightly different pressure on the chemical potentials of the solid or of the components of the solution. More important, corrections must be made for the non-ideality of the pure gas and of the gaseous mixture. With these corrections, equation (A2.1.60) can be verified within experimental error. 

To proceed fiirther, to evaluate the standard free energy AG , we need infonnation (experimental or theoretical) about the particular reaction. One source of infonnation is the equilibrium constant for a chemical reaction involving gases. Previous sections have shown how the chemical potential for a species in a gaseous mixture or in a dilute solution (and the corresponding activities) can be defined and measured. Thus, if one can detennine (by some kind of analysis)... 

The alternative to direct simulation of two-phase coexistence is the calculation of free energies or chemical potentials together with solution of the themiodynamic coexistence conditions. Thus, we must solve (say) pj (P) = PjjCT ) at constant T. A reasonable approach [173. 174. 175 and 176] is to conduct constant-AT J simulations, measure p by test-particle insertion, and also to note that the simulations give the derivative 3p/3 7 =(F)/A directly. Thus, conducting... 

Two methods are used to measure pH electrometric and chemical indicator (1 7). The most common is electrometric and uses the commercial pH meter with a glass electrode. This procedure is based on the measurement of the difference between the pH of an unknown or test solution and that of a standard solution. The instmment measures the emf developed between the glass electrode and a reference electrode of constant potential. The difference in emf when the electrodes are removed from the standard solution and placed in the test solution is converted to a difference in pH. Electrodes based on metal—metal oxides, eg, antimony—antimony oxide (see Antimony AND ANTIMONY ALLOYS Antimony COMPOUNDS), have also found use as pH sensors (8), especially for industrial appHcations where superior mechanical stabiUty is needed (see Sensors). However, because of the presence of the metallic element, these electrodes suffer from interferences by oxidation—reduction systems in the test solution. 

CU-CUSO4 electrodes with saturated CUSO4 solution are recommended for potential measurements in soil. Their potential constancy is about 5 mV. Larger errors can be traced to chemical changes in the CUSO4 solution. These electrodes have been developed for long-life applications in potential-controlled rectifiers and built-... 

Thermodynamic information can also be obtained from simulations. Currently we are measuring the differences in chemical potential of various small molecules in dimethylimidazolium chloride. This involves gradually transforming one molecule into another and is a computationally intensive process. One preliminary result is that the difference in chemical potential of propane and dimethyl ether is about 17.5 kj/mol. These molecules are similar in size, but differ in their polarity. Not surprisingly, the polar ether is stabilized relative to the non-polar propane in the presence of the ionic liquid. One can also investigate the local arrangement of the ions around the solute and the contribution of different parts of the interaction to the energy. Thus, while both molecules have a favorable Lennard-Jones interaction with the cation, the main electrostatic interaction is that between the chloride ion and the ether molecule. 

Fig. 5.8 The energy levels of n-type M0S2 at the flat band potential relative to the positions of various redox couples in CH3CN/[n-Bu4N]C104 solution. The valence band edge of the semiconductor as revealed by accurate flat band potential measurement is at ca. +1.9 V vs. SCE implying that photooxrdations workable at Ti02 are thermodynamically possible at illuminated M0S2 as well. (Reproduced with permission from [137], Copyright 2010, American Chemical Society)...

A relatively new arrangement for the study of the interfacial region is achieved by so-called emersed electrodes. This experimental technique developed by Hansen et al. consists of fully or partially removing the electrode from the solution at a constant electrical potential. This ex situ experiment (Fig. 9), usually called an emersion process, makes possible an analysis of an electrode in an ambient atmosphere or an ultrahigh vacuum (UHV). Research using modem surface analysis such as electron spectroscopy for chemical analysis (ESCA), electroreflectance, as well as surface resistance, electrical current, and in particular Volta potential measurements, have shown that the essential features (e.g., the charge on... 

With a three-component system, such as a polymer in an aqueous salt solution, preferential adsorption of one component to the polymer can affect the analysis of light-scattering data.199 Such interactions can affect the SRI. Therefore, measurements of the SRI must be made at constant chemical potential. Constant chemical potential is achieved experimentally by dialyzing the solvent and polymer solution to equilibrium through a membrane permeable to the solvent but impermeable to the polymer.199... 

Equations (2) and (3) relate intermolecular interactions to measurable solution thermodynamic properties. Several features of these two relations are worth noting. The first is the test-particle method, an implementation of the potential distribution theorem now widely used in molecular simulations (Frenkel and Smit, 1996). In the test-particle method, the excess chemical potential of a solute is evaluated by generating an ensemble of microscopic configurations for the solvent molecules alone. The solute is then superposed onto each configuration and the solute-solvent interaction potential energy calculated to give the probability distribution, Po(AU/kT), illustrated in Figure 3. The excess... 

Computing thermodynamic properties is the most important validation of simulations of solutions and biophysical materials. The potential distribution theorem (PDT) presents a partition function to be evaluated for the excess chemical potential of a molecular component which is part of a general thermodynamic system. The excess chemical potential of a component a is that part of the chemical potential of Gibbs which would vanish if the intermolecular interactions were to vanish. Therefore, it is just the part of that chemical potential that is interesting for consideration of a complex solution from a molecular basis. Since the excess chemical potential is measurable, it also serves the purpose of validating molecular simulations. 

Because the chemical potentials of water distributed in two phases (i.e., solution and vapor) must be equal, the water activity of a food can be measured by bringing the food into equilibrium with the air above it. At equilibrium, under conditions of constant temperature and pressure, the aw values of the aqueous phase of a food (aw l) and of the air (aw v) are equal and can be estimated from the ratio of the partial vapor pressure of water above the food (pv) to the vapor pressure of pure water (p") at the same temperature (Walstra, 2003) ... 

Since the polymeric chains unlike to the common molecules possess by free energy of the conformation F (or by negative entropy of conformation which is a measure of polymeric chains self-organization [13]), it should be included as an additional term in usual determination of chemical potential of component of the solution. Hence, we have for the macromolecules... 

As will be seen later (Section V.l), meaningful molecular weights in multicomponent systems can be determined, if the specific refractive index increment appertains to conditions of constant chemical potential of low molecular weight solvents (instead of at constant composition). Practically, this can be realised by dialysing the solution against the mixed solvent and then measuring the specific refractive index increment of the dialysed solution. The theory and practice have been reviewed4-14-1S> 72>. 

As seen from Eq. (130) an activity coefficient may deviate significantly from unity at higher salt concentrations. The activity coefficient can therefore also be used as a measure of the deviation of the salt solution from a thermodynamically ideal solution. If the chemical potential of a solute in a (pressure-dependent) standard state of infinite dilution is /x°, we find the standard partial molar volume from... 

---