Sodium hydroxide test

Put into a mortar 10 cc. of water and 3 or 4 drops of a dilute solution of sodium hydroxide. Test the solution with red litmus paper. Next add some casein and grind it thoroughly in the alkaline solution. Test the solution again with red litmus paper. What conclusion can you draw in regard to the chemical nature of casein. Filter the solution through a wet filter-paper, and add to the filtrate a few drops of a solution of calcium chloride. Explain. 

Part 1 Chemieal analysis (a) chloride (b) aeid soluble sulfate (c) impurities affecting setting and hardening of cement (d) impurities that affect surface finish (e) water solubility, (f) loss on ignition (g) slag unsoundness (h) free lime (i) fulvo acid test (j) sodium hydroxide test . 

Weigh accurately into a 250-ml conical flask an amount of sample expected to contain from 0 08 to 0 09 g As. If (a) soluble in water, dissolve in 30 ml of water (b) insoluble in water, dissolve in 5 ml of N sodium hydroxide and 20 ml of water and add 5 ml of N sulphuric acid (c) containing chloride, dissolve in 50 ml of water. Place several glass beads in the flask and a small funnel in the neck, add 8 g of ammonium persulphate and boil briskly until colourless and for two minutes longer. (In the case of sodium cacodylate heat for about five minutes after ebullition commences.) Add cautiously 50 ml of approximately N oxalic acid and boil vigorously for five minutes. Add cautiously 40 ml of dilute sulphuric acid and 10 ml of potassium iodide solution. Boil vigorously until the volume is reduced to about 40 ml. Cool, just remove the pale yellow colour by the addition of approximately 01N sodium sulphite drop by drop (1 to 3 drops usually) and immediately add about 60 ml of water. Add 1 drop of phenolphthalein solution and sufficient sodium hydroxide test solution to render just alkaline. Add 10 ml of dilute sulphuric acid, mix, cool, neutralise with sodium bicarbonate, add up to 5 g in excess and titrate with 0 1 N iodine. If starch solution is used add it just before the end-point is reached. 

To 40 ml of sodium hydroxide test solution add 80 ml of dilute sulphuric acid, 1 drop of phenolphthalein solution and dilute sulphuric acid until colourless then add 10 ml of acid in excess, 10 ml of potassium iodide solution and cool. Neutralise with sodium bicarbonate and add up to 5 g in excess. Titrate with O IN iodine and deduct the reading from that obtained above. 1 ml of O IN iodine = 0 003746 g As. 

Note cautiously the characteristic odour of acetaldehyde which this solution possesses. Then with the solution carry out the following general tests for aldehydes described on p. 341 Test No. I (SchiflF s reagent). No. 3 (Action of sodium hydroxide). No. 4 (Reduction of ammoniacal silver nitrate). Finally perform the two special tests for acetaldehyde given on p. 344 (Nitroprusside test and the Iodoform reaction). 

Place 5 mi. of ethyl acetate in a 100 ml. round-bottomed flask, and add about 50 ml. of 10% sodium hydroxide solution, together with some fragments of ungiazed porcelain. Fit the flask with a reflux water-condenser, and boil the mixture gently over a wire gauze for 30 minutes. Now disconnect the condenser, and fit it by means of a bent delivery-tube (or knee-tube ) to the flask for direct distillation (Fig. 59, or Fig. 23(0), p. 45). Reheat the liquid, and collect the first 10 ml. of distillate, which will consist of a dilute aqueous solution of ethanol. Confirm the presence of ethanol by the iodoform test Test 3, p. 336). 

Place I g. of benzamide and 15 ml. of 10% aqueous sodium hydroxide solution in a 100 ml. conical flask fitted with a reflux water-condenser, and boil the mixture gently for 30 minutes, during which period ammonia is freely evolved. Now cool the solution in ice-water, and add concentrated hydrochloric acid until the mixture is strongly acid. Benzoic acid immediately separates. Allow the mixture to stand in the ice-water for a few minutes, and then filter off the benzoic add at the pump, wash with cold water, and drain. Recrystallise from hot water. The benzoic acid is obtained as colourless crystals, m.p. 121°, almost insoluble in cold water yield, o 8 g. (almost theoretical). Confirm the identity of the benzoic acid by the tests given on p. 347. 

Place about i g. of the base in a test-tube, and cover with concentrated (about 20%) sodium hydroxide solution. Bring the mixture gently to the boil, keeping the test-tube lightly closed with the finger meanwhile to prevent undue escape of vapour.. A.s the solution boils a strong fishy odour of dimethylamine is detected, and white fumes form when the test-tube is held near an open bottle of concentrated... 

Nitrogen. To one portion of the filtrate, add z-3 ml. of 10, aqueous sodium hydroxide solution, then add about o-2 g. of ferrous sulphate and proceed as in the Lassaigiie nitrogen test (p, 322). Note, however, that the fiUal acidification with dilute siiphiiric acid must be made with care, owing to the vigorous evolution of carbon dioxide from the carbonate present. 

It is preferable to use Tollen s ammoniacal silver nitrate reagent, which is prepared as follows Dissolve 3 g. of silver nitrate in 30 ml. of water (solution A) and 3 g. of sodium hydroxide in 30 ml. of water (solution B). When the reagent is requir, mix equal volumes (say, 1 ml.) of solutions A and JB in a clean test-tube, and add dilute ammonia solution drop by drop until the silver oxide is just dissolved. Great care must be taken in the preparation and use of this reagent, which must not be heated. Only a small volume should be prepared just before use, any residue washed down the sink with a large quantity of water, and the test-tubes rinsed with dilute nitric acid. 

Hydrolysis (or saponification) of n-butyl acetate. Boil 4-5 g. of n-butyl acetate (Section 111,95) with 50 ml. of 10 per cent, sodium hydroxide solution under reflux until the odour of the ester can no longer be detected (about 1 hour). Set the condenser for downward distiUation and coUect the first 10 ml. of distillate. Saturate it with potassium carbonate, aUow to stand for 5 minutes, and withdraw all the Uquid into a small pipette or dropper pipette. AUow the lower layer of carbonate solution to run slowly into a test-tube, and place the upper layer into a small test-tube or weighing bottle. Dry the alcohol with about one quarter of its buUr of anhydrous potassium carbonate. Remove the alcohol with a dropper pipette and divide it into two parts use one portion for the determination of the b.p. by the Siwoloboff method (Section 11,12) and convert the other portion into the 3 5-dinitrobenzoate (Section III, 27) and determine the m.p. 

Acidify the residue in the flask with dUute sulphuric acid and distil off 10-15 ml. of the solution. Test a smaU portion of the distillate for acidity, and also observe the odour. Neutralise the main portion with sodium hydroxide solution (add a drop of phenolphthalein to act as indicator), evaporate to smaU bulk, and convert the sodium salt into the p-bromophenacyl ester or into some other suitable derivative (Section 111,85) determine the m.p. of the derivative. 

Into a 750 ml. round-bottomed flask furnished with a reflux condenser place a solution of 34 g. (18-5 ml.) of concentrated sulphuric acid in 100 ml, of water add 33 g. of di-n-butyl cyanamide and a few fragments of porous porcelain. Reflux gently for 6 hours. Cool the resulting homogeneous solution and pour in a cold solution of 52 g. of sodium hydroxide in 95 ml. of water down the side of the flask so that most of it settles at the bottom without mixing with the solution in the flask. Connect the flask with a condenser for downward distillation and shake it to mix the two layers the free amine separates. Heat the flask when the amine with some water distils continue the distillation until no amine separates from a test portion of the distillate. Estimate the weight of water in the distillate anp add about half this amount of potassium hydroxide in the form of sticks, so that it dissolves slowly. 

Method 1. Place in a test-tube or small flask 1-3 g. of glycerol and 30 ml. of 10 per cent, sodium hydroxide solution add gradually, with simultaneous shaking, 1-2 g. of benzoyl chloride. Stopper the vessel, shake for several minutes and allow to stand. Decant the solution from the pasty solid and wash the latter with cold water by decantation. Recrystallise the solid tribenzoate from dilute rectified (or methylated) spirit or from light petroleum, b.p. 40-60° the pure compound has m.p. 76°. 

Heat a mixture of 15 g. of p-nitroacetanilide and 75 ml. of 70 per cent, sulphuric acid (1) under a reflux water condenser for 20-30 minutes or until a test sample remains clear upon dilution with 2-3 times its volume of water. The p-nitroaniline is now present in the hquid as the sulphate. Pour the clear hot solution into 500 ml. of cold water and precipitate the p-nitroanihne by adding excess of 10 per cent, sodium hydroxide solution or of concentrated ammonia solution. When cold (cool the mixture in ice water, if necessary), filter the yellow crystalline precipitate at the pump, wash it well with water, and drain thoroughly. Recrystallise it from a mixture of equal volumes of rectified (or methylated) spirit and water or from hot water. Filter, wash and dry. The yield of p-nitroanihne, m.p, 148°, is 11 g. 

Hydrolysis of benzanilide. Place 5 g. of benzanilide and 50 ml. of 70 per cent, sulphuric acid in a small flask fitted with a reflux condenser, and boU gently for 30 minutes. Some of the benzoio acid will vapourise in the steam and solidify in the condenser. Pour 60 ml. of hot water down the condenser this will dislodge and partially dissolve the benzoic acid. Cool the flask in ice water filter off the benzoic acid (anifine sulphate does not separate at this dilution), wash well with water, drain, dry upon filter paper, and identify by m.p. (121°) and other tests. Render the filtrate alkaline by cautiously adding 10 per cent, sodium hydroxide solution, cool and isolate the aniline by ether extraction. Recover the ether and test the residue for anifine (Section IV,100). 

SULPHONATION OF AROMATIC AMINES If aniline is treated with excess of concentrated sulphuric acid and the resulting mixture, which contains aniline sulphate, is heated at 180° until a test portion when mixed with sodium hydroxide solution no longer liberates aniline, p-aminobenzenesulphonic acid or sulphanilic acid is formed this separates as the dihydrate upon pouring the cooled mixture into water. The reaction prohahly proceeds as follows ... 

Place a mixture of 25 g. of a-naphthylamine (Section IV,37) and 125 g. (69 -5 ml.) of concentrated sulphuric acid in a 250 ml. conical or round-bottomed flask, and heat in an oil bath for 4-5 hours or until a test sample, when made alkaline with sodium hydroxide solution and extracted with ether, yields no naphthylamine upon evaporation of the ether. Pour the warm reaction mixture cautiously and with stirring into 300 ml. of cold... 

The sodium sulphite solution may also be prepared by dissolving 100 g. of pure (or a corresponding quantity of commercial) sodium hydroxide in about 125 ml. of water, and then diluting to 750 ml. The flask is cooled in running water, a few drops of phenolphthalein indicator are added, and sulphur dioxide passed in until the pink colour just disappears (it is advisable to add a further 1-2 drops of the indicator at this point) and then for 2-3 minutes longer. It is best to remove a sample for test from time to time, dilute with 3-4 volumes of water, and test with I drop of phenolphthalein. 

Dissolve 1 g. of the secondary amine in 3-5 ml. of dilute hydrochloric acid or of alcohol (in the latter case, add 1 ml. of concentrated hydrochloric acid). Cool to about 5° and add 4-5 ml. of 10 per cent, sodium nitrite solution, and allow to stand for 5 minutes. Add 10 ml. of water, transfer to a small separatory funnel and extract the oil with about 20 ml. of ether. Wash the ethereal extract successively with water, dilute sodium hydroxide solution and water. Remove the ether on a previously warmed water bath no flames should be present in the vicinity. Apply Liebermann s nitroso reaction to the residual oil or solid thus. Place 1 drop or 0 01-0 02 g. of the nitroso compovmd in a dry test-tube, add 0 05 g. of phenol and warm together for 20 seconds cool, and add 1 ml. of concentrated sulphuric acid. An intense green (or greenish-blue) colouration will be developed, which changes to pale red upon pouring into 30-50 ml. of cold water the colour becomes deep blue or green upon adding excess of sodium hydroxide solution. 

Dissolve 1 0 g. of the compound in 5 ml. of dry chloroform in a dry test-tuhe, cool to 0°, and add dropwise 5g. (2-8 ml.) of redistilled chloro-sulphonic acid. When the evolution of hydrogen chloride subsides, allow the reaction mixture to stand at room temperature for 20 minutes. Pour the contents of the test-tube cautiously on to 25 g. of crushed ice contained in a small beaker. Separate the chloroform layer and wash it with a httle cold water. Add the chloroform layer, with stirring, to 10 ml. of concentrated ammonia solution. After 10 minutes, evaporate the chloroform on a water bath, cool the residue and treat it with 5 ml. of 10 per cent, sodium hydroxide solution the sulphonamide dissolves as the sodium derivative, RO.CgH4.SO,NHNa. Filter the solution to remove any insoluble matter (sulphone, etc.), acidify the filtrate with dilute hydrochloric acid, and cool in ice water. Collect the sulphonamide and recrystallise it from dilute alcohol. 

Place in a dry test-tube 0 -5 g. of the compound and an equal bulk of pure phthahc anhydride, mix well together, and add 1 drop of concentrated sulphuric acid. Stand the tube for 3-4 minutes in a smah beaker of concentrated sulphuric acid or oil previously heated to 160°, Remove from the bath, allow to cool, add 4 ml. of 5 per cent, sodium hydroxide solution and stir until the fused mass has dissolved. Dilute with an equal... 

To a mixture of 10 g. of the compound and 3-5 ml. of 33 per cent, sodium hydroxide solution in a test-tube, add 2-5 ml. of 50 per cent, chloroacetic acid solution. If necessary, add a little water to dissolve the sodium salt of the phenol. Stopper the test-tube loosely and heat on agently-boiling water bath for an hour. After cooling, dilute with 10 ml. of water, acidify to Congo red with dilute hydrochloric acid, and extract with 30 ml. of ether. Wash the ethereal extract with 10 ml, of water, and extract the aryloxyacetic acid b shaking with 25 ml. of 5 per cent, sodium carbonate solution. Acidify the sodium carbonate extract (to Congo red) with dilute hydrochloric acid, collect the aryloxyacetic acid which separates, and recrystallise it from hot water. 

Aromatic aldehydes react with the dimedone reagent (Section 111,70,2). All aromatic aldehydes (i) reduce ammoniacal silver nitrate solution and (ii) restore the colour of SchifiF s reagent many react with sodium bisulphite solution. They do not, in general, reduce Fehling s solution or Benedict s solution. Unlike aliphatic aldehydes, they usually undergo the Cannizzaro reaction (see Section IV,123) under the influence of sodium hydroxide solution. For full experimental details of the above tests, see under Ali-phalic Aldehydes, Section 111,70. They are easily oxidised by dilute alkaline permanganate solution at the ordinary temperature after removal of the manganese dioxide by sulphur dioxide or by sodium bisulphite, the acid can be obtained by acidification of the solution. 

Method 2. Into a 500 ml. round-bottomed flask place 120 ml. of dry A.R. benzene, and 35 g. (29 ml.) of redistilled benzoyl chloride. Weigh out 30 g. of finely-powdered, anhydrous aluminium chloride into a dry corked test-tube, and add the solid, with frequent shaking, during 10 minutes to the contents of the flask. Fit a reflux condenser to the flask, and heat on a water bath for 3 hours or until hydrogen chloride is no longer evolved. Pour the contents of the flask wliile still warm into a mixture of 200 g. of crushed ice and 100 ml. of concentrated hydrochloric acid. Separate the upper benzene layer (filter first, if necessary), wash it with 50 ml. of 5 per cent, sodium hydroxide solution, then with water, and dry with anhydrous magnesium sulphate. Isolate the benzophenone as in Method 1. The yield is 30 g. 

---