Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Single supports

Fig. 7. Vessel support and arrangement where d = nozzle diameter, D = vessel diameter, and L = length. Saddles can be straight or tapered. Single supports can be used for small dmms. Combining dmms saves the number of necessary supports (7). Fig. 7. Vessel support and arrangement where d = nozzle diameter, D = vessel diameter, and L = length. Saddles can be straight or tapered. Single supports can be used for small dmms. Combining dmms saves the number of necessary supports (7).
The insert rack is designed for easy installation and removal through an unused nozzle. The supporting rods (one for each specimen) are welded to a single support plate that is of a width that enables it to be introduced through the nozzle. However, this too cannot be inserted unless the equipment is out of service, although its introduction does not require removal of gas. [Pg.1067]

M. Eikerling, J. Meier, and U. Stimming. Hydrogen evolution at a single supported nanoparticle A kinetic model. Zeitschrift fur Phystkalische Chemie 217 (2003) 395-414. [Pg.433]

The commercial availability of PS-based supports in nonbead format such as pins (27, 28), crowns (29, 30), microtubes (31), and recently discs (32) has also had a notable impact on the field of SPS. These devices allow the attachment of significantly higher amounts of compound onto a single support unit compared to resin beads. They are similar in nature to the PS resin supports, but their different morphology requires different handling procedures than resin beads we will discuss some of their specific properties in the following chapters as related to specific examples. [Pg.6]

FEM measurements of melting temperature establish for the first time the detailed dependence of this important quantity on particle size over the size range of interest to catalysis. Further studies of the electron emission from a single supported cluster have broad potential for determining the electronic structure of catalytic particles. [Pg.339]

After introduction of chromium on AIF3, FT-IR spectrum did not show substantial changes relative to the single support on the other hand these spectra have been obtained in transmittance with use of KBr pellets. This technique allows the characterization of the bulk, but it is very difficult to characterize the chromium species on the surface. The characterization of the samples obtained after the various preparation steps of the catalyst through UV-Vis spectroscopy in diffuse reflectance is reported in Fig. 2. [Pg.945]

None of the studies at higher ionic strength at 25 °C is a systematic study in which the concentration of a single supporting electrolyte was varied. The results are summarised in Table V-26. [Pg.187]

The steps to apply the SEA method for the synthesis of a single supported metal are as follows ... [Pg.49]

In this paper, we had employed binary carbon supports to fabricate thin film electrodes in DMFCs. The roles of binary carbon supports and an optimal mixing ratio will be evaluated and characterized through cyclic voltammetry measurements. It will be shown that with the usage of two carbon supports, electrochemical activities and loading contents of catalysts can be enhanced. This improvement is further exemplified by the enhanced electrode kinetics of methanol oxidation for a binary carbon support-electrode in comparison to a single support-electrode. [Pg.427]

Note that (1) for this antisymmetric excitation only the first mode is excited , and (2) because both supports undergo identical motion, the response analysis reduces to the standard case of a single support excitation. [Pg.399]

The top of a non-self-supporting ladder must be placed with two rails supported equally unless it is equipped with a single support attachment. Ladders must not be moved, shifted, or extended while in use. Ladders must have nonconductive... [Pg.442]

There are, in principle, two different ways of rail fastening by elastic adhesives spot-wise bonding on single supports and continuous bonding. Both methods require... [Pg.472]

Figure 114 Single support (1) Chair, (2) Rail, (3) Elastic adhesive, (4) Anchor bolt, (5) Concrete track bed. Figure 114 Single support (1) Chair, (2) Rail, (3) Elastic adhesive, (4) Anchor bolt, (5) Concrete track bed.
Figure 115 Single support fastening on a bridge (Inselbriicke, Stuttgart, Germany). Figure 115 Single support fastening on a bridge (Inselbriicke, Stuttgart, Germany).
The system is subjected to horizontal components of the earthquake ground motion (single-support excitation assumption). [Pg.183]

Eikerling M, Meier J, Stimming U. Hydrogen evolution at a single supported nanoparticle a kinetic model. Z Phys Chem 2003 217(4) 395—414. [Pg.443]

Free for clamped continuous support Single supports Edge beams Ribs... [Pg.193]

What Exxon Chemical Co. has developed is a new level of molecular control that can solve all of these limitations. Exxon has developed unique isotactic PP homopolymers and copolymers made in one reactor using dual metallocene catalysts on a single support. The copolymer is bimodal and probably the first true bimodal resin made in a single reactor. [Pg.44]


See other pages where Single supports is mentioned: [Pg.230]    [Pg.696]    [Pg.37]    [Pg.531]    [Pg.358]    [Pg.593]    [Pg.467]    [Pg.505]    [Pg.530]    [Pg.198]    [Pg.364]    [Pg.93]    [Pg.137]    [Pg.181]    [Pg.306]    [Pg.312]    [Pg.170]    [Pg.326]    [Pg.65]    [Pg.473]    [Pg.473]    [Pg.105]    [Pg.164]    [Pg.178]    [Pg.395]    [Pg.2036]   
See also in sourсe #XX -- [ Pg.193 ]




SEARCH



© 2024 chempedia.info