Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Service repair

External floating roo cheaper to constmct than double deck for 5—50-m diameter suitable for high vapor pressure stocks capable of in-service repair of appurtenances good buoyancy... [Pg.312]

IEEE Std 500-1984 (IEEE, 1984) contains failure rate and out of service, repair and restoration times for electrical electronic, and sensing component, and mechanical equipment. It is a considerable improvement over IEEE STD 500-1977. The reported values are the consensus of over 200 experts. Each expert submitted a low, recommended, and a high value for the failure rate... [Pg.153]

Details of any adjustments, servicing, repairs, and modifications carried out The name of the person performing the calibration Details of any limitation on its use... [Pg.417]

Standards Development General FC Vehicle Safety SAE Fuel Cell Vehicle Systems SAE Fuel System Components CSA Containers SAE Reformers SAE Emissions SAE Recycling SAE Service/Repair SAE... [Pg.481]

The support resources available to service, repair, and calibrate the control system must also be considered when selecting a system they are considerable and can be estimated from the literature (48—50). [Pg.42]

In the example of the drop in cooling water pH, cleaning is probably unnecessary, but the entire system should be repassivated. Whereas following out of service repairs to a heat exchanger, the exchanger should be cleaned, either mechanically or with an appropriate chemical cleaner, and then properly passivated before being put back on-line. [Pg.336]

Machinery Services Coatings Surface Technologies Pump Products Services Turbine Equipment Services Repair Maintenance Services Fuel Cell Systems... [Pg.382]

THE PROGRAM IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY, FITNESS, RESULTS TO BE OBTAINED, AND OF PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE UNSATISFACTORY OR DEFICIENT, YOU (AND NOT GULF PUBUSHING COMPANY OR ANY AUTHORIZED SOFTWARE DEALER) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. [Pg.209]

EXCEPT AS SPECIFIED ABOVE, THE LICENSED PROGRAM AND USER MANUAL(S) ARE FURNISHED BY WILEY ON AN "AS IS" BASIS AND without WARRANTY AS TO THE PERFORMANCE OR RESULTS YOU M.AY OBTAIN BY USING THE LICENSED PROGRAM AND USER MaNUAL(S). THE ENTIRE RISK AS TO THE RESULTS OR PERFORMANCE. AND THE COST OF ALL NECESS.ARY SERVICING. REPAIR. OR CORRECTION OF THE LICENSED PROGRAM AND USER MANUALfS) IS ASSUMED BY YOU. [Pg.677]

Impacts from road infrastructure (road constmction, maintenance, visual impacts estimated In monetary terms in Table 6.10) Impacts from car infrastructure (service, repair, traffic police courts, insurance mostly included in cost given In Table 6.9) ... [Pg.376]

AAs a provider of a hands-on service (repairing, maintaining, or upgrading someone s computer), you need to be aware of some general safety tips, because if you are not careful, you could harm yourself or the equipment. Birst, let s talk about playing it safe. Computers, display monitors, and printers can be dangerous if not handled properly. [Pg.39]

As the name implies these drawings are used by engineers to fit together, or assemble, aU the parts as the final product and by maintenance engineers during servicing, repair or replacement of worn parts. An example of an assembly drawing is shown in Fig. 20.5. [Pg.334]

Ensure maintenance is maintaining vehicle service, repair, and inspection records as required — including roadside inspection reports. [Pg.58]

Bolting may be advantageous in the repair of defective bonded joints and in the in-service repair of damaged structures. In both cases bolts transfer significant loads in the debonded areas and reduce peak stresses in the adhesive, since they enable the adhesive to be stressed to a higher level than before the repair. Bolts can also provide the clamping pressure required in bonding. This is often beneficial in repairs. [Pg.506]

Consumer Service Consumers may need help with assembly, installation, service, repair, parts, and other matters to keep their products safe. Manufacturers can use product registration to help notify users of recalls and safety notices. [Pg.560]

Effects of High-Temperature High-Pressure Carbon Dioxide Decompression on Elastomeric Materials Design, Fabrication and Surface Finish of Metcil Tanks and Vessels to be Lined for Chemical Immersion Service Repair of Lining Systems... [Pg.861]

Think about this. How many companies have you heard of building service (repair) centers as they are designing a new product We have a tendency to anticipate that the product we are building is going to fail. Do we want this in our management system This is the same as someone developing safety policies and procedures or guarding machines after an... [Pg.509]

All equipment and working surfaces that could have become contaminated must be cleaned and decontaminated as necessary. If thorough decontamination cannot be done immediately, a label must be attached to equipment stating which portions of the equipment remain contaminated to inform downstream servicing/repair employees of the hazard and precautions they need to take. [Pg.86]

Predictable and regular basis means employee functions such as, but not limited to, inspections, service, repair, and maintenance which are performed ... [Pg.131]

Date of inspection —Name (initials) of inspector —Disposition -Return to service -Repair -Scrap... [Pg.66]

Dave Kuiawa is the director of training and fieid services at industriai Scientific Corporation. Dave has been with industrial Scientific for 23 years and has heid positions in customer service, repair service, training, product management, saies and fieid services. Dave can be reached at dkuiawa indsci. com. [Pg.28]

If the burner cutoff level is not at, or slightly above, the lowest permissible water level, the low-water cutoff should be moved to the proper elevation, or should be serviced, repaired, or even replaced if necessary. [Pg.892]

Scheduled service repairs and routine periodic maintenance of gas chromatographs are a critical part of a good quality assurance program and will save time in the long run. A well-maintained instrument will give more reliable and reproducible data, and the lifetime of the instrument will be extended. [Pg.974]

Service/Repair SAE API,AGA,CGS Fuel Transfer NFPA, API UL, CSA International, API,CGA Codes for the Environment ... [Pg.624]

Drivers or vehicles are not to continue operating if the driver or vehicle was placed out of service for any reason. The consequences can be severe if a driver drives before the Out-of-Service situation has been rectified or if the vehicle is driven before the Out-of-Service repairs are made. A driver convicted of violating an Out-of-Service order will be subject to a fine and a disqualification period. [Pg.100]


See other pages where Service repair is mentioned: [Pg.312]    [Pg.496]    [Pg.1175]    [Pg.28]    [Pg.72]    [Pg.72]    [Pg.72]    [Pg.13]    [Pg.312]    [Pg.218]    [Pg.21]    [Pg.29]    [Pg.442]    [Pg.393]    [Pg.393]    [Pg.395]    [Pg.1175]    [Pg.2908]    [Pg.276]    [Pg.228]    [Pg.36]    [Pg.6]    [Pg.326]   
See also in sourсe #XX -- [ Pg.316 , Pg.331 , Pg.340 ]




SEARCH



© 2024 chempedia.info