Series-connected tubes

In the Philips total oxygen demand meter the zirconium oxide is specially prepared and is in the form of two series connected tubes or cells through which a nitrogen carrier gas is allowed to flow. Each cell is provided with two pairs of annular (internal and external) electrodes and the whole assembly is maintained at about 600°C. 

The most common type of commercial pyrolysis equipment is the direct fired tubular heater in which the reacting material flows through several tubes connected in series. The tubes receive thermal energy by being immersed in an oil or gas furnace. The pyrolysis products are cooled rapidly after leaving the furnace and enter the separation train. Constraints on materials of construction limit the maximum temperature of the tubes to 1500 °F. Thus the effluent from the tubes should be restricted to temperatures of 1475 °F or less. You may presume that all reactor tubes and return bends are exposed to a thermal flux of 10,000 BTU/... 

Experiments involving the release of radioactive carbon dioxide from MSMA-14C treated soils were conducted in a system consisting of two test tubes connected in series. One tube contained 5g of treated soil (at 10 and lOOppm of monosodium methane arsenic acid carbon dioxide while a second tube contained a trapping mixture, 2-methoxyethanol and monoethanolamine (7-10, v/v). Carbon dioxide-free air was passed over the soil and metabolic 14CO was collected in the trapping solution. The soils studied were Sharkey cldy, Hagerstown silty clay loam, Cecil sandy loam, and Dundee silty clay loam. All soils were initially adjusted to field capacity and maintained at 28-30°C the evolved 14CO was sampled periodically. Some properties of these soils are shown in Tabfe 13.1. 

For the manufacture of carbon disulphide on the large scale, the charcoal is contained in a large vertical cast-iron cylinder, ten to twelve feet high and from one to two feet in diameter. This cylinder is surrounded by brickwork and heated by a fire beneath. The sulphur is introduced through a hopper connected with a side tube at the base of the cylinder. The carbon disulphide vapour is led away from the top of the cylinder through a pipe, the end of which dips under water, where most of the product condenses. Beyond the water condenser is a series of tubes in which condensation is completed. Hydrogen sulphide, one of the impurities, escapes condensation and passes on, being subsequently absorbed in slaked lime.4... 

Detectors are not limited to solo use they can be hooked in series to get more information from the same sample. In a serial operation, be sure that the refractive index detector or electrochemical detector is the last in the line. Their flow cells are more fragile than UV and fluorescence cells and won t take the increased back-pressure. Keep the tubing diameter fine and as short as possible to avoid band spreading. You must correct for connecting tubing volume (time) delay in comparing chromatograms from the two detectors. 

Distribution of a single solute Consider a series of tubes numbered 0,1,2,3,..., r, each containing (for the sake of simplicity) equal volumes of an aqueous phase and an immiscible organic liquid of lower density. A solute is placed in the aqueous phase of tube 0. After equilibrium is reached, the organic phase of tube 0 is transferred to tube 1 as that of tube 1 is transferred to tube 2, and so forth. The process of equilibration and transfer is repeated n times each time, all upper organic layers are transferred to the next higher tube in sequence. The mechanics of connecting the vessels and of the transfer process need not concern us here. ... 

When the residence time becomes shorter, this approach becomes questionable for several reasons. For example, the asymptotic state may not have been reached yet, or the peaks may be unsymmetrical. These "short-time" situations may be encountered when trying to apply chromatographic concepts to the study of dispersion in connecting tubes, or in some apphcations, such as hollow-fiber liquid chromatography. Shankar and Lenhoff [77] have derived a solution in the time domain, using series expansion. This solution can be implemented by numerical computation for the determination of concentration profiles inside a tube coated with a retentive layer, when the fluid flow is laminar. This solution is valid for systems that are either short or long after the Taylor-Aris definition. 

Develop better tube-to-tube series connections for high voltage, low current operation. 

The integrated planar (IP) SOFC stack concept, for instance, applied by Rolls-Royce Fuel Cell Systems, uses an array of series-connected cells deposited by screen printing onto a flat support tube, a schematic cross section of which is shown Fig. 21.23. The support tube, an inert, porous ceramic, is fabricated from a magnesia magnesium aluminate spinel (MMA), whereby the desired coefficient of thermal expansion is adjusted by the ratio of the base materials [76]. 

---