Sample preparation solvent selection

The first concern in the selection of the sample preparation solvent is to optimize recovery. However, a secondary consideration is the sample solvent s effect on the analysis. This is true whether the analytical technique is ultraviolet spectroscopy (UV), high-performance liquid chromatography (HPLC), or gas chromatography (GC). The method development sequence can be described as (a) development of the chromatographic separation, (b) development of the sample preparation method, and then (c) evaluation and optimization of the interaction of the sample preparation with the instrumental method. 

Advantages of NIR include speed, little or no sample preparation, solvents and reagents are rarely needed, high dynamic concentration range, and deep sample penetration. NIR obeys the same selection rules as mid-IR. Only molecules that exhibit a dipole moment will absorb NIR radiation. 

Solubilizing all or part of a sample matrix by contacting with liquids is one of the most widely used sample preparation techniques for gases, vapors, liquids or solids. Additional selectivity is possible by distributing the sample between pairs of immiscible liquids in which the analyte and its matrix have different solubilities. Equipment requirements are generally very simple for solvent extraction techniques. Table 8.2 [4,10], and solutions are easy to manipulate, convenient to inject into chromatographic instruments, and even small volumes of liquids can be measured accurately. Solids can be recovered from volatile solvents by evaporation. Since relatively large solvent volumes are used in most extraction procedures, solvent impurities, contaminants, etc., are always a common cause for concern [65,66]. 

High selectivity (i.e. the ability to separate analytes from matrix interferences) is one of the most powerful aspects of SPE. This highly selective nature of SPE is based on the extraction sorbent chemistry, on the great variety of possible sorbent/solvent combinations to effect highly selective extractions (more limited in LLE where immiscible liquids are needed) and on the choice of SPE operating modes. Consequently, SPE solves many of the most demanding sample preparation problems. 

Sample preparation for the common desorption/ionisation (DI) methods varies greatly. Films of solid inorganic or organic samples may be analysed with DI mass spectrometry, but sample preparation as a solution for LSIMS and FAB is far more common. The sample molecules are dissolved in a low-vapour-pressure liquid solvent - usually glycerol or nitrobenzyl alcohol. Other solvents have also been used for more specialised applications. Key requirements for the solvent matrix are sample solubility, low solvent volatility and muted acid - base or redox reactivity. In FAB and LSIMS, the special art of sample preparation in the selection of a solvent matrix, and then manipulation of the mass spectral data afterwards to minimise its contribution, still predominates. Incident particles in FAB and LSIMS are generated in filament ionisation sources or plasma discharge sources. 

Over thirty different elements have been determined in medical and biological materials by atomic absorption spectroscopy. The popularity of the technique is due to a number of factors, including sensitivity, selectivity, and ease of sample preparation. With biological fluids, often no preparation at all is required. The techniques employed usually involve simple dilution of the sample with water or with an appropriate reagent to eliminate interference. Alternatively, the element to be determined is separated by solvent extraction. Either an untreated sample, a protein free filtrate, or an ashed sample is extracted. 

Sample preparation for analysis by hyphenated methods requires some additional planning when compared to nonhyphenated methods. All steps, extraction, concentration, and final solvent selection must take into consideration and be compatible with all the components of the hyphenated instrumentation. For gas chromatographic methods, all the components in the mixture must be in the gaseous state. For liquid chromatography (LC) or high-performance liquid chromatography (HPLC), the samples of the analytes of interest can be solids or liquids, neutral or charged molecules, or ions, but they must be in solution. If the follow-on analysis is by MS, then each of the analytes may require a different method of introduction into the MS. Metals and metal ions may be introduced by HPLC if they are in solution but commonly are introduced via AAS or inductively coupled plasma (ICP). Other analytes may be directly introduced from HPLC to MS [2],... 

The preparation of aqueous solutions from solids is usually performed after the sample has been ground to a powder of uniform size. Sometimes, samples can be only sparingly soluble in water and therefore organic solvents may be used to dissolve the sample. Organic solvents can increase the sensitivities of atomic spectrometric analyses as a result of increases in the efficiencies of the nebulization of the analyte solutions. When organic solvents are used to dissolve samples non-selective ligands should be added to complex ionic species that would otherwise be insoluble in the organic solvent. 

FIA star 5010 Modular, semi- or fully automatic operation. May be operated with process controller microprocessor. Can be set up in various combinations with 5017 sampler and superflow software which is designed to run on IBM PC/XT computer 60-180 samples h Dialysis for in-line sample preparation and in-line solvent extraction.Thermostat to speed up reactions. Spectrophotometer (400-700nm) or photometer can be connected to any flow through detector, e.g. UV/visible, inductively coupled plasma, atomic absorption spectrometer and ion-selective electrodes... 

The use of robotics can be adopted also in sample preparation steps, in particular on-line SPE [7], This necessity is particular evident when small quantity of starting materials is available and the target molecules are present at low concentration levels. With the advent of miniaturization and automated procedures for samples handling, treatments and analysis, the lost of analytes due to a laboratory steps can be reduced. The reduction of analyte losses and the possibility to analyze even a total sample (no loss) leads to lower limits of detection (and consequently lower limits of quantification). Smaller volumes bring to obtain adequate sensitivity and selectivity for a large variety of compounds. In addition, on-line SPE requires low solvent consumption without the need to remove all residual water from cartridges, since elution solvents are compatible with the separation methods. 

A pivotal step in the analytical process is sample preparation. Frequently liquid-liquid extractions (LLEs) are used. Solvents, pH, and multiple back extractions are all manipulated to increase selectivity and decrease unwanted contaminants before injection on the GC system. Solid phase extraction (SPE) is more convenient than it used to be because of an increase in commercially available SPE columns. SPE columns are packed with an inert material that binds the drug of interest, allowing impurities to pass through. As with LEE, solvent choices and pH affect retention and recovery. There are three commercially available types of SPE columns, diatomaceous earth (which uses the same principles as LLE), polystyrene-divinylbenzene copolymer, and mixed mode bonded silica (Franke and de Zeeuw, 1998). 

In summary, the use of RPLC is ideal for pharmaceutical analyses because of the broad range of commercially available stationary phases because the most common RPLC mobile phases (buffers with acetonitrile or methanol) have low UV cut-off wavelengths, which facilitate high sensitivity detection for quantitation of low-level impurities and because selectivity can readily be controlled via mobile phase optimization. Additionally, the samples generated for selectivity screening (as detailed above) are typically aqueous based. In subsequent phases of pharmaceutical development, aqueous-based sample solvents are ideal for sample preparation and are, under limited constraints, compatible with MS detection required to identify impurities and degradation products. 

---