Rheology Solution

CELLULOSE ETHER THICKENERS - KEY ELEMENTS FOR COMPLETE RHEOLOGY SOLUTIONS... 

Cellulose Ether Thickeners - Key Elements for Complete Rheology Solutions... 

The given presentation of the mechanism of the interaction of polymer molecules with turbulent flow admits a peculiar theoretical examination. The presence of polymer addition besides the increase of longitudinal viscosity is resulted in the appearance of such rheological solution properties as elastic plasticity, pseudo-plasticity, anisotropy. In [3] the influence of different rheological fluid characteristics on the wall turbulence is theoretically analyzed within the limits of monoharmonic approximation, which affords to take into account turbulent blows-out. Different variants of rheological behaviour were considered. For all that we succeded to show, that the decrease of turbulent friction arose only in mediums, possessing... 

Holzwarth, G., Polysaccharide from Xanthomonas Campestris Rheology, Solution Conformation and Flow Through Small Pores, Symposium on Advances in Petroleum Recovery presented before the Division of Petroleum Chemistry, Inc., ACS New York meeting, April 4-9 (1976a). 

In this article, the synthesis, characterization, rheology, solution processing, and mechanical properties of novel molecular composites are discussed. These molecular composite are block copolymers composed of a liquid-crystalline polyamide and two amorphous polyimides. Also, the rheological properties of both isotorpic and anisotropic solutions of PBTA homopolymers and PBTA/PI block copolymers are... 

Solution Rheology. Solutions of polyacrylamides tend to behave as pseudoplastic fluids in viscometric flows. Dilute solutions are Newtonian (viscosity is independent of shear rate) at low shear rates and transition to pseudoplastic, shear thinning behavior above a critical value of the shear rate. This critical shear rate decreases with the polymer molecular weight, polymer concentration, and the thermodynamic quality of the solvent. A second Newtonian plateau at high shear rates is not readily seen, probably because of mechanical degradation of the chains... 

We also offer information on testing/quality control in this issue, with articles on rheological tests ( Rheology Solutions, pp. 30-32) and industry icon John Johnston s impact on the testing and development of pressure-sensitive adhesives ( Passing the Torch, pp. 33-36). Be sure to take a look at the issue s full Table of Contents on p. 5, or simply scan the mobile tag on the cover for direct access to all of our content online. 

Most properties of linear polymers are controlled by two different factors. The chemical constitution of tire monomers detennines tire interaction strengtli between tire chains, tire interactions of tire polymer witli host molecules or witli interfaces. The monomer stmcture also detennines tire possible local confonnations of tire polymer chain. This relationship between the molecular stmcture and any interaction witli surrounding molecules is similar to tliat found for low-molecular-weight compounds. The second important parameter tliat controls polymer properties is tire molecular weight. Contrary to tire situation for low-molecular-weight compounds, it plays a fimdamental role in polymer behaviour. It detennines tire slow-mode dynamics and tire viscosity of polymers in solutions and in tire melt. These properties are of utmost importance in polymer rheology and condition tlieir processability. The mechanical properties, solubility and miscibility of different polymers also depend on tlieir molecular weights. 

These normal stresses are more pronounced for polymers with a very broad molecular weight distribution. Viscosities and viscoelastic behavior decrease with increasing temperature. In some cases a marked viscosity decrease with time is observed in solutions stored at constant temperature and 2ero shear. The decrease may be due to changes in polymer conformation. The rheological behavior of pure polyacrylamides over wide concentration ranges has been reviewed (5). 

Suspension- and emulsion-polymerized PVDF exhibit dissimilar behavior in solutions. The suspension resin type is readily soluble in many solvents even in good solvents, solutions of the emulsion resin type contain fractions of microgel, which contain more head-to-head chain defects than the soluble fraction of the resin (116). Concentrated solutions (15 wt %) and melt rheology of various PVDF types also display different behavior (132). The Mark-Houwink relation (rj = KM°-) for PVDF in A/-methylpyrrohdinone (NMP) containing 0.1 molar LiBr at 85°C, for the suspension (115) and emulsion... 

Solutions of rhamsan have high viscosity at low shear rates and low gum concentrations (90). The rheological properties and suspension capabiUty combined with excellent salt compatibihty, make it useful for several industrial apphcations including agricultural fertilizer suspensions, pigment suspensions, cleaners, and paints and coatings. 

Significant use properties of poly(ethylene oxide) are complete water solubiHty, low toxicity, unique solution rheology, complexation with organic acids, low ash content, and thermoplasticity. 

Rheology. PVP solubihty in water is limited only by the viscosity of the resulting solution. The heat of solution is — 16.61 kJ/mol (—3.97 kcal/mol) (79) aqueous solutions are slightly acidic (pH 4—5). Figure 2 illustrates the kinematic viscosity of PVP in aqueous solution. The kinematic viscosity of PVP K-30 in various organic solvents is given in Table 13. 

Starches. Starch (qv) granules must be cooked before they wiU release their water-soluble molecules. It is common to speak of solutions of polysaccharides, but in general, they do not form tme solutions because of their molecular sizes and intermolecular interactions rather they form molecular dispersions. The general rheological properties of polysaccharides like the starch polysaccharides are described below under the discussion of polysaccharides as water-soluble gums. Starch use permeates the entire economy because it (com starch in particular) is abundantly available and inexpensive. Another key factor to its widespread use is the fact that it occurs in the form of granules. 

As substituent uniformity is increased, either by choosing appropriate reaction conditions or by reaction to high degrees of substitution, thixotropic behavior decreases. CMCs of DS >1.0 generally exhibit pseudoplastic rather than thixotropic rheology. Pseudoplastic solutions also decrease in viscosity under shear but recover instantaneously after the shear stress is removed. A plot of shear rate versus shear stress does not show a hysteresis loop. 

Solutions of HEC are pseudoplastic. Newtonian rheology is approached by very dilute solutions as well as by lower molecular-weight products. Viscosities change Httie between pH 2 and 12, but are affected by acid hydrolysis or alkaline oxidation under pH and temperature extremes. Viscosities of HEC solutions change reversibly with temperature, increasing when cooled and decreasing when warmed. 

---