Reverse osmosis cellulose triacetate membranes

R/0 unit Reverse Osmosis Unit for water purification in small aquariums and miniature yard-ponds, utilizes a membrane under pressure to filter dissolved solids and pollutants from the water. Two different filter membranes can be used the CTA (cellulose triacetate) membrane is less expensive, but only works with chlorinated water and removes 50-70% of nitrates, and the TFC membrane, which is more expensive, removes 95% of nitrates, but is ruined by chlorine. R/0 wastes water and a system that cleans 100 gallons a day will cost ft-om 400 to 600 with membrane replacement adding to the cost. A unit that handles 140 gallons a day will cost above 700,00. 

Seawater or brackish water can be purified by reverse osmosis. To maximise the flow of water through a polymer membrane, the polymer must have a high water permeability, yet a low permeability for the salts. To maximise efficiency, the membrane area must be large and its thickness as small as possible consistent with a lack of pinholes. A high pressure is applied to the salt water side of the membrane. Because it is thin, a cellulose triacetate membrane is supported on a porous cellulose nitrate-cellulose acetate support structure to resist the pressure. To make the unit compact the composite membrane is spirally wound on to an inner cylinder, and the edges glued together. When a pressure of 70 bar is applied to the seawater side, NaCl rejection levels in excess of 99.7% can be achieved. 

Polymer Plasticizer. Nylon, cellulose, and cellulose esters can be plasticized using sulfolane to improve flexibiUty and to increase elongation of the polymer (130,131). More importantly, sulfolane is a preferred plasticizer for the synthesis of cellulose hoUow fibers, which are used as permeabiUty membranes in reverse osmosis (qv) cells (131—133) (see Hollow-FIBERMEMBRANEs). In the preparation of the hoUow fibers, a molten mixture of sulfolane and cellulose triacetate is extmded through a die to form the hoUow fiber. The sulfolane is subsequently extracted from the fiber with water to give a permeable, plasticizer-free, hoUow fiber. 

As Figure 5.12 shows, Toray s PEC-1000 crosslinked furfuryl alcohol membrane has by far the best sodium chloride rejection combined with good fluxes. This explains the sustained interest in this membrane despite its extreme sensitivity to dissolved chlorine and oxygen in the feed water. Hollow fine fiber membranes made from cellulose triacetate by Toyobo or aromatic polyamides by Permasep (Du Pont) are also comfortably in the one-stage seawater desalination performance range, but the water fluxes of these membranes are low. However, because large-surface-area, hollow fine fiber reverse osmosis modules can be... 

The fastest growing desalination process is a membrane separation process called reverse osmosis (RO). The most remarkable advantage of RO is that it consumes little energy since no phase change is involved in the process. RO employs hydraulic pressure to overcome the osmotic pressure of the salt solution, causing water-selective permeation from the saline side of a membrane to the freshwater side as the membrane barrier rejects salts [1-4], Polymeric membranes are usually fabricated from materials such as cellulose acetate (CA), cellulose triacetate (CTA), and polyamide (PA) by the dry-wet phase inversion technique or by coating aromatic PA via interfacial polymerization (IFP) [5]. 

Reverse osmosis membranes were first developed from cellulose acetate (CA) and a cellulose triacetate (CTA). These CA and CTA membranes have been in commercial use for many years. The CTA membrane, especially, is continuing to be used all over the world today. This wide adoption demonstrates that the CTA membrane is excellent as a RO... 

Vasarhelyi K, Ronner JA, Mulder MHV, Smolders CA. Development of wet-dry reversible reverse osmosis membranes with high performance from cellulose acetate and cellulose triacetate blends. Desalination. 1987 61 211-235... 

---