Reactors liquid-phase reactions

The equilibrium conversion can be increased by employing one reactant in excess (or removing the water formed, or both). b. Inerts concentration. Sometimes, an inert material is present in the reactor. This might be a solvent in a liquid-phase reaction or an inert gas in a gas-phase reaction. Consider the reaction system... 

Increasing the pressure of irreversible vapor-phase reactions increases the rate of reaction and hence decreases reactor volume both by decreasing the residence time required for a given reactor conversion and increasing the vapor density. In general, pressure has little effect on the rate of liquid-phase reactions. 

For liquid-phase reactions, the effect of pressure on the selectivity and reactor volume is less pronounced, and the pressure is likely to be chosen to... 

Having considered reactor temperature and pressure, we are now in a position to judge whether the reactor phase will be gas, liquid, or multiphase. Given a free choice between gas- and liquid-phase reactions, operation in the liquid phase is usually preferred. Consider the single reaction system from Eq. (2.19) ... 

Clearly, in the liquid phase much higher concentrations of Cfeed (kmol m ) can be maintained than in the gas phase. This makes liquid-phase reactions in general more rapid and hence leads to smaller reactor volumes for liquid-phase reactors. 

By contrast, if the reactor is continuous well-mixed, then the reactor is isothermal. This behavior is typical of stirred tanks used for liquid-phase reactions or fluidized-bed reactors used for gas-phase reactions. The mixing causes the temperature in the reactor to be effectively uniform. 

In chemical laboratories, small flasks and beakers are used for liquid phase reactions. Here, a charge of reactants is added and brought to reaction temperature. The reaction may be held at this condition for a predetermined time before the product is discharged. This batch reactor is characterized by the varying extent of reaction and properties of the reaction mixture with time. In contrast to the flasks are large cylindrical tubes used in the petrochemical industry for the cracking of hydrocarbons. This process is continuous with reactants in the tubes and the products obtained from the exit. The extent of reaction and properties, such as composition and temperature, depend on the position along the tube and does not depend on the time. 

Homogeneous reactions are those in which the reactants, products, and any catalysts used form one continuous phase (gaseous or liquid). Homogeneous gas phase reactors are almost always operated continuously, whereas liquid phase reactors may be batch or continuous. Tubular (pipeline) reactors arc normally used for homogeneous gas phase reactions (e.g., in the thermal cracking of petroleum of dichloroethane lo vinyl chloride). Both tubular and stirred tank reactors are used for homogeneous liquid phase reactions. 

Pipeline reactor for gaseous or liquid phase reactions Turbulent 1 or 2 six-element modules... 

Piston Flow in Contact with a CSTR. A liquid-phase reaction in a spray tower is conceptually similar to the transpired-wall reactors in Section 3.3. The liquid drops are in piston flow but absorb components from a well-mixed gas phase. The rate of absorption is a function of as it can be in a transpired-wall reactor. The component balance for the piston flow phase is... 

There is an additional point to be made about this type of processing. Many gas-phase processes are carried out in a continuous-flow manner on the macro scale, as industrial or laboratory-scale processes. Hence already the conventional processes resemble the flow sheets of micro-reactor processing, i.e. there is similarity between macro and micro processing. This is a fimdamental difference from most liquid-phase reactions that are performed typically batch-wise, e.g. using stirred glass vessels in the laboratory or stirred steel tanks in industrial pilot or production plants. 

Micro Reactors for Liquid-phase and Liquid/Liquid-phase Reactions... 

An nth-order homogeneous liquid phase reaction is carried out in a batch tank reactor. 

Tubular reactors are generally used for gaseous reactions, but are also suitable for some liquid-phase reactions. 

Batch reactors are often used for liquid phase reactions, particularly when the required production is small. They are seldom employed on a commercial scale for gas-phase reactions because the quantity of product that can be produced in reasonably sized reactors is small. Batch reactors are well suited for producing small quantities of material or for producing several different products from one piece of equipment. Consequently they find extensive use in the pharmaceutical and dyestuff industries and in the production of certain specialty chemicals where such flexibility is desired. When rapid fouling is encountered or contamination of fermentation cultures is to be avoided, batch operation is preferable to continuous processing because it facilitates the necessary cleaning and sanitation procedures. 

Large stirred tank reactors are generally not suited for use at high pressures because of mechanical strength limitations. They are used mainly for liquid phase reaction systems at low or medium pressures when appreciable residence times are required. 

Other advantages of the tubular reactor relative to stirred tanks include suitability for use at higher pressures and temperatures, and the fact that severe energy transfer constraints may be readily surmounted using this configuration. The tubular reactor is usually employed for liquid phase reactions when relatively short residence times are needed to effect the desired chemical transformation. It is the reactor of choice for continuous gas phase operations. 

Continuous flow stirred tank reactors are normally just what the name implies—tanks into which reactants flow and from which a product stream is removed on a continuous basis. CFSTR, CSTR, C-star, and back-mix reactor are only a few of the names applied to the idealized stirred tank flow reactor. We will use the letters CSTR as a shorthand notation in this textbook. The virtues of a stirred tank reactor lie in its simplicity of construction and the relative ease with which it may be controlled. These reactors are used primarily for carrying out liquid phase reactions in the organic chemicals... 

Since one is almost always concerned with liquid phase reactions when dealing with stirred tank reactors, the assumption of constant fluid density is usually appropriate. In this case equation 8.3.6 can be written as... 

---