Reactor chain transfer

In production, anhydrous formaldehyde is continuously fed to a reactor containing well-agitated inert solvent, especially a hydrocarbon, in which monomer is sparingly soluble. Initiator, especially amine, and chain-transfer agent are also fed to the reactor (5,16,17). The reaction is quite exothermic and polymerisation temperature is maintained below 75°C (typically near 40°C) by evaporation of the solvent. Polymer is not soluble in the solvent and precipitates early in the reaction. 

The enthalpy of the copolymerization of trioxane is such that bulk polymerization is feasible. For production, molten trioxane, initiator, and comonomer are fed to the reactor a chain-transfer agent is in eluded if desired. Polymerization proceeds in bulk with precipitation of polymer and the reactor must supply enough shearing to continually break up the polymer bed, reduce particle size, and provide good heat transfer. The mixing requirements for the bulk polymerization of trioxane have been reviewed (22). Raw copolymer is obtained as fine emmb or flake containing imbibed formaldehyde and trioxane which are substantially removed in subsequent treatments which may be combined with removal of unstable end groups. 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

If a linear mbber is used as a feedstock for the mass process (85), the mbber becomes insoluble in the mixture of monomers and SAN polymer which is formed in the reactors, and discrete mbber particles are formed. This is referred to as phase inversion since the continuous phase shifts from mbber to SAN. Grafting of some of the SAN onto the mbber particles occurs as in the emulsion process. Typically, the mass-produced mbber particles are larger (0.5 to 5 llm) than those of emulsion-based ABS (0.1 to 1 llm) and contain much larger internal occlusions of SAN polymer. The reaction recipe can include polymerization initiators, chain-transfer agents, and other additives. Diluents are sometimes used to reduce the viscosity of the monomer and polymer mixture to faciUtate processing at high conversion. The product from the reactor system is devolatilized to remove the unreacted monomers and is then pelletized. Equipment used for devolatilization includes single- and twin-screw extmders, and flash and thin film evaporators. Unreacted monomers are recovered for recycle to the reactors to improve the process yield. 

Suspension polymerization of VDE in water are batch processes in autoclaves designed to limit scale formation (91). Most systems operate from 30 to 100°C and are initiated with monomer-soluble organic free-radical initiators such as diisopropyl peroxydicarbonate (92—96), tert-huty peroxypivalate (97), or / fZ-amyl peroxypivalate (98). Usually water-soluble polymers, eg, cellulose derivatives or poly(vinyl alcohol), are used as suspending agents to reduce coalescence of polymer particles. Organic solvents that may act as a reaction accelerator or chain-transfer agent are often employed. The reactor product is a slurry of suspended polymer particles, usually spheres of 30—100 pm in diameter they are separated from the water phase thoroughly washed and dried. Size and internal stmcture of beads, ie, porosity, and dispersant residues affect how the resin performs in appHcations. 

Anionic polymerization offers fast polymerization rates on account of the long life-time of polystyryl carbanions. Early studies have focused on this attribute, most of which were conducted at short reactor residence times (< 1 h), at relatively low temperatures (10—50°C), and in low chain-transfer solvents (typically benzene) to ensure that premature termination did not take place. Also, relatively low degrees of polymerization (DP) were typically studied. Continuous commercial free-radical solution polymerization processes to make PS, on the other hand, operate at relatively high temperatures (>100° C), at long residence times (>1.5 h), utilize a chain-transfer solvent (ethylbenzene), and produce polymer in the range of 1000—1500 DP. 

Solution Polymerization. Solution polymerization of vinyl acetate is carried out mainly as an intermediate step to the manufacture of poly(vinyl alcohol). A small amount of solution-polymerized vinyl acetate is prepared for the merchant market. When solution polymerization is carried out, the solvent acts as a chain-transfer agent, and depending on its transfer constant, has an effect on the molecular weight of the product. The rate of polymerization is also affected by the solvent but not in the same way as the degree of polymerization. The reactivity of the solvent-derived radical plays an important part. Chain-transfer constants for solvents in vinyl acetate polymerizations have been tabulated (13). Continuous solution polymers of poly(vinyl acetate) in tubular reactors have been prepared at high yield and throughput (73,74). 

The production rate is 2—4 t/h, depending on the feed rate, monomer concentration in the feed, and conversion. The conversion of isobutylene and isoprene typically ranges from 75—95% and 45—85%, respectively, depending on the grade of butyl mbber being produced. The composition and mol wt of the polymer formed depend on the concentration of the monomers in the reactor Hquid phase and the amount of chain transfer and terminating species present. The Hquid-phase composition is a function of the feed composition and the extent of monomer conversion. In practice, the principal operating variable is the flow rate of the initiator/coinitiator solution to the reactor residence time is normally 30—60 minutes. 

The reactors had relatively limited heat transfer capability and polyrates therefore had to be kept low. This was accomplished by operating at low temperatures. (The rate in the CSTR s was about. 5%/hr.). Since chain transfer agents were not employed, product Staudinger molecular weight was about 100,000, very high by current commercial standards. 

In process variants for HIPS ( 7, 28), the feed solution to the first reactor, besides styrene and ethylbenzene, will also contain dissolved polybutadiene rubber along with antioxidants, chain transfer agents, and possibly mineral oil. 

This work particularly emphasizes the importance of selecting the initiator system for optimum reactor operation and reveals general concepts which specify the desired properties and operational modes of an optimum initiator system. In addition, the effects of the system heat transfer and the CTA (chain transfer agent) level on the conversion-molecular weights relationships are presented. 

Figure 7 shows the limiting maximum molecular weight of products from a reactor of fixed size varies directly with the frequency factor of the initiator at a fixed activation energy, while the limiting conversion varies inversely with the frequency factor. In addition, the length of the chain-transfer controlled zone is increased inversely with the frequency factor. 

There is less information available in the scientific literature on the influence of forced oscillations in the control variables in polymerization reactions. A decade ago two independent theoretical studies appeared which considered the effect of periodic operation on a free radically initiated chain reaction in a well mixed isothermal reactor. Ray (11) examined a reaction mechanism with and without chain transfer to monomer. 

We begin the discussion of EPM by elaborating on this physical picture. Figure 1 shows a typical emulsion CSTR reactor and polymerization recipe. The magnified portion of the latex shows the various phases and the major species involved. The latex consists of monomers, water, surfactant, initiator, chain transfer agent, and added electrolyte. We used the mechanism for particle formation as described in Feeney et al. (8-9) and Hansen and Ugelstad (2). We have not found it necessary to invoke the micellar entry theory 2, 2/ 6./ 11/ 12/ 14. 

When an aqueous phase radical enters the polymer particles it becomes a polymer phase radical, which reacts with a monomer molecule starting a propagating polymer chain. This chain may be stopped by chain transfer to monomer, by chain transfer to agent or it may terminate by coupling. Small radicals in the particle may also desorb from or reenter the particle. In a batch reactor. Interval I indicates the new particle formation period, Interval II particle growth with no new particles, and Interval III the absence of monomer droplets. 

Polymerizations were carried out in a jacketed, 1-gal, stirred, pressure tank reactor. Typical reactions were run by adding water, alcohol, or chain transfer agent, phosphate buffer, and persulfate to the reactor. The reactor was pressurized with CTFE monomer. Sulfite solution was fed at a rate to maintain reaction. Copper and iron ions were used at times as catalysts by adding cupric sulfate or ferrous sulfate.3 The product was filtered, washed with 90 10 water methanol followed with deionized water. The product was dried at 110°C. 

Styrene monomer (SM), 23 325 chain transfer to, 23 383 physical properties of, 23 3271 Styrene monomer advanced reactor... 

This is the simplest process and is widely used for synthesis of condensation polymers. The system is homogeneous and consists of monomer/polymer. In this process the monomer and initiator are kept in a reactor and heated to suitable temperature. The chain transfer agent whenever used for controlling the Molecular weight is also dissolved in the monomer. 

For addition polymerisation without chain termination or chain transfer, eqns. (73) and (77) may be used for a batch reactor when fe = fep. Here, the growing chains have similar histories and hence the final molecular weight distribution can be very narrow. Similar results would be expected from a plug-flow reactor. The mole fraction of A , 7 , is given by... 

If free-radical polymerisation is carried out in an ideal back-mixed flow reactor, the concentrations of the reactant species become constant and the molecular weight distributions can be obtained from eqns. (83) and (84). Figure 8 shows how changes in P /Pn with conversion compare for the two reactor types. These plots represent idealised behaviour, in practice, Pw/Pn will be influenced by changes in at high conversion and by the occurrence of chain transfer reactions. 

---