Reaction liter

In a sort of reciprocal arrangement, the cell also feeds many intermediates back into the TCA cycle from other reactions. Since such reactions replenish the TCA cycle intermediates, Hans Kornberg proposed that they be called anaplerotie reactions (literally, the filling up reactions). Thus, PEP carboxylase and pyruvate carboxylase synthesize oxaloacetate from pyruvate (Figure 20.24). 

Bifunctional condensation, according to the very nature of the process, necessarily leads to products of finite molecular weight. In view of the impossibility of forcing the condensation reaction literally to completion, there will always be some few unreacted functional groups. These mark the ends of the linear molecules, which therefore are finite in length. 

The emulsifier in emulsion polymerization has three key functions, namely stabilizing the monomer droplets during the first stage of the emulsion polymerization, supplying surfactant micelles as the site of the polymerization reaction (literally the micelles can be regarded as some kind of micro-reactors) and stabilizing the latex particles at the end of the emulsion polymerization process pending transportation,... 

Example 86 A 0.10 mole amount of the starting 3-(4-hydroxyphenyl) propylene, 0.25 mole of methyl nitrite, 0.5 liter of methyl alcohol, and 0.006 mole of a palladium chloride catalyst were charged into a reaction vessel. Then, the reaction was carried out at a temperature of 20.degree. C. for 1.5hours."... 

Hydrophilic (Section 19 5) Literally water loving a term applied to substances that are soluble in water usually be cause of their ability to form hydrogen bonds with water Hydrophobic (Section 19 5) Literally water hating a term applied to substances that are not soluble in water but are soluble in nonpolar hydrocarbon like media Hydroxylation (Section 15 5) Reaction or sequence of reac tions in which an alkene is converted to a vicinal diol Hyperconjugation (Section 4 10) Delocalization of a electrons... 

B. cis-1,2-Gyclohexanedimethanol Dimethanesulfonate. In a 5-1., three-necked, round-bottomed flask, immersed in an ice-salt bath and fitted with a mechanical stirrer and an addition funnel, is plaeed a solution of 111 g. (0.97 mole) of methanesulfonyl chloride in 1.21. of pyridine. While cooling and stirring, a solution of 46.4 g. (0.322 mole) of m-l,2-cyclohexanedimethanol in 250 ml. of pyridine is added dropwise at a rate such that the temperature does not exceed 0° (Note 5). Upon completion of the addition, the mixture is stirred at — 5° to 0° for an additional 2 hours. Two liters of cold 10% hydrochloric acid is introduced at a rate which maintains the reaction mixture below 20° (Note 5). The solid which separates is isolated by suction filtration, washed sequentially with 11. of dilute hydrochloric acid and 21. of water, and air-dried. There is isolated 93-95 g. (96-98%) of the dimethanesulfonate having m.p. 66-67.5°. Reorystallization from methanol gives needles melting at 75-76° (Note 6). 

After the initial hydrogenation studies were completed with WVGS 13407, all other liquefaction experiments were conducted in a larger, 3.8-liter bolted-closure autoclave fitted with an electrically driven magnetic stirrer arbitrarily set to provide mixmg at 1000 rpm. A temperature controller and power supply were connected to a three-zone furnace to control reaction temperature... 

Nc = 0.0 gmol, Nq = 0.0 gmol, respectively. A mixture of A and B is charged into a 1-liter reactor. Determine the holding time required to achieve 90% fractional conversion of A (X = 0.9). The rate constant is k = 1.0 X 10 [(liter) /(gmoP min)] and the reaction is first order in A, second order in B and third order overall. 

The general reaction procedure and apparatus used are exactly as described in Procedure 2. Ammonia (465 ml) is distilled into a 2-liter reaction flask and to this is added 165mlofisopropylalcoholandasolutionof30g(0.195 mole) of 17/ -estradiol 3-methyl ether (mp 118.5-120°) in 180 ml of tetrahydrofuran. The steroid is only partially soluble in the mixture. A 5 g portion of sodium (26 g, 1.13 g-atoms total) is added to the stirred mixture and the solid dissolves in the light blue solution within several min. As additional metal is added, the mixture becomes dark blue and a solid (matted needles) separates. Stirring is inefficient for a few minutes until the mass of crystals breaks down. All of the sodium is consumed after 1 hr and 120 ml of methanol is then added to the mixture with care. The product is isolated as in Procedure 4h 2. After being air-dried, the solid weighs 32.5 g (ca. 100% for a monohydrate). A sample of the material is dried for analysis and analyzed as described in Procedure 2 enol ether, 91% unreduced aromatics, 0.3%. The crude product may be crystallized from acetone-water or preferably from hexane. 

The reduction is carried out much as described in Procedure 2. Ammonia (950 ml) is distilled into a 5-liter reaction flask and 950 ml of /-amyl alcohol and a solution of the ketal in 950 ml of methylcyclohexane are added with good stirring. Sodium (57 g, 2.5 g-atoms) is added in portions. The reaction mixture becomes blue within 30-45 min after the sodium is added and the metal is consumed within about 3 hr after the blue color appears. After the mixture becomes colorless, 200 ml of ethanol is added and the ammonia is allowed to boil off through a mercury trap. Then 500 ml of water and 500 ml 0% potassium bicarbonate solution are added and the organic layer is separated. The organic layer is washed once with 10 % potassium bicarbonate... 

The reaction mixture is diluted with 250 ml of water, the mixture is transferred to a 2 liter flask using methanol as a wash liquid, and the organic solvents are distilled at 20-25 mm using a rotary vacuum evaporator. The product separates as a solid and distillation is continued until most of the residual toluene has been removed. The solid is collected on a 90 cm, medium porosity, fritted glass Buchner funnel and washed well with cold water. After the material has been sucked dry, it is covered with a little cold methanol, the mixture is stirred to break up lumps, and the slurry is kept for 5 min. The vacuum is reapplied, the solid is rinsed with a little methanol followed by ether, and the material is air-dried to give 9.1 g (85%), mp 207-213° after sintering at ca. 198°. Reported mp 212-213°. The crude material contains 1.0-1.5% of unreduced starting material as shown by the UV spectrum. Further purification may be effected by crystallization from methanol. 

A solution of 7.2 g of sodium borohydride (analyzing at 87 % purity) in 300 ml of pyridine is added dropwise, with vigorous stirring, over 7 hr to a solution of 50 g of pregnane-3,11,20-trione in 100 ml of pyridine and 18 ml of water. The temperature is kept at 18-20°. The stirring at this temperature is continued for another 2 hr, after which the reaction mixture is poured slowly into dilute hydrochloric acid (575 ml of cone hydrochloric acid in 5.2 liters of water) and the stirring continued for 1 hr. The precipitate is filtered, washed with... 

Dimethyl sulfate (16 g) is added to a mixture of dimethyl carbonate (400 g) and deuterium oxide (1(X) g) in a 1 liter flask. Two reflux condensers and a drying tube are attached in series (initial rapid evolution of carbon dioxide may entrain some liquid), and the reaction mixture is heated under reflux for 72 hr. The methanol-OD is distilled directly from the reaction flask through a 30 cm Vigreux column. Redistillation from a small amount of sodium yields 275 g of pure methanol-OD bp 66-66.5° isotopic purity, 98.6%. ... 

Hydrocortisone Crude hydrocortisone bissemicarbazone (50 g) is dissolved at 20° in 2.5 liters of 2.4 N hydrochloric acid under a nitrogen atmosphere. The solution is cooled to 5°, and then a solution of 25 g of sodium nitrite in 250 ml of water is added over a 15 min period, the temperature being maintained at 5 + 1°. The reaction mixture is stirred for an additional 30 min at 5°, then treated with a solution of 150 g of urea in 250 ml of water over a 15 min period and finally neutralized below 15° with 20% sodium hydroxide. The mixture is extracted several times with chloroform and the solvent is evaporated under reduced pressure to give 33 g of crude hydrocortisone, mp 197-203°. Crystallization from acetone-Darco gives 26.4 g (69.5%) of pure hydrocortisone mp 216-221° [oc]d 151° (Diox). 

Silver cyanate should be freshly prepared. The commercial material has a pronounced gray color and is totally unsuitable for this reaction. Best results are obtained when the following preparation is carried out in the dark. To 100 g of silver nitrate in 3 liters of distilled water is added with stirring 49.5 g of potassium cyanate in 700 ml of distilled water. The white precipitate is filtered through a large Buchner funnel (Coors No. 5) and the filter cake is washed with 500 ml water, then with 300 ml methanol, and finally with... 

The dry tosylhydrazone (20 g, 45.5 mmol) is dissolved in 750 ml of 1,2-dimethoxyethane (freshly distilled from lithium aluminum hydride) in a flame-dried 1 liter round bottom flask fitted with a 240 ml addition funnel, a drierite tube and a magnetic stirrer. A 2.05 M ether solution of methyllithium (130 ml, Alfa Inorganics, Inc.—Caution to avoid the mineral oil impurity the methyllithium solution is decanted from a cold solution which contains a precipitate) is placed in the dropping funnel and added over a 60 min period. The temperature of the reaction mixture increases to ca. 35° during the addition however, no cooling precautions are required. The highly colored reaction mixture is stirred for 7 hr and then poured into 1.5 liters of ice water. The flocculent precipitate is digested for 12 hr at room temperature to speed the filtration. After filtration the filter cake is washed with 500 ml water and dried under vacuum at 50° for several hr. The androsta-5,16-dien-3l5-ol is obtained in ca. 70% yield after recrystallization from methanol mp 138-139°. 

A slow stream of purified and dried acetylene is passed for 3 hr through a solution containing 25 ml (75 mmoles) of a 3 TV solution of methyl magnesium bromide and 100 ml of anhydrous tetrahydrofuran. A solution consisting of 5 g (17 mmoles) of 3)5-hydroxyandrost-5-en-17-one and 50 ml of anhydrous tetrahydrofuran is then added and the mixture is boiled at reflux for 15 min, during which time a heavy precipitate forms. The reaction mixture is cooled and poured into 1 liter of water containing 20 ml of concentrated sulfuric acid. The crude product is obtained as a precipitate, which is filtered, washed with water and dried to yield 5.2 g of 17a-ethynylandrost-5-ene-3, 17 -diol mp 228-232°. One crystallization from chloroform-hexane yields 4.5 g (83%) mp 238-240° [[Pg.73]

A 50% aqueous solution of potassium hydroxide (160 ml) is added at —5° over a period of 30 min to a mixture consisting of 80 g (0.78 moles) N-nitrosomethylurea, 104 g (0.32 moles) 3 -acetoxy-5a-pregna-9(ll),16-dien-20-one and 1 liter of methylene dichloride. The mixture is allowed to come to room temperature and the reaction is continued for 2 hr. The mixture is stirred for 15 min and 1.5 liters of water is added slowly in order to discharge any excess of diazomethane. The layers are separated and the aqueous phase is extracted with 300 ml of methylene dichloride. The organic phase is washed with water dried and concentrated. The residue is triturated with 750 ml of petroleum (bp 100-120°) and the resulting solid is dried in vacuo at 100° to give 106.5 g (92%) of the pyrazoline mp 158° (dec.) [ah 72° (CHCI3) 2 3, 229 mfi (e 1,167). 

Methoxy-cis-19-norpregna-l,3,5(10),17(20)-tetraene A solution of 31 g (109 mmolesi of estrone methyl ether in 600 ml of benzene is added rapidly to a solution of 469 mmoles of ethylidenetriphenylphosphorane in 1.2 liters of DMSO. After heating under nitrogen at 60° overnight, the reaction is cooled, poured into ice water, and extracted with three portions of hexane, backwashed with three portions of water and the hexane removed. The crude product, dissolved in petroleum ether (bp, 30-60°), is filtered through 225 g of alumina (activity I). The residue from the eluate consists of 95 % cis- and 5 % tran5-isomers, as determined by vpc analysis. After recrystallization from ether-methanol, 26.3 g (82%) of cw-isomer is obtained mp 76.5-77.5° [a]o 60°. 

---