Copolymer, composition random

Eree-radical initiation of emulsion copolymers produces a random polymerisation in which the trans/cis ratio caimot be controlled. The nature of ESBR free-radical polymerisation results in the polymer being heterogeneous, with a broad molecular weight distribution and random copolymer composition. The microstmcture is not amenable to manipulation, although the temperature of the polymerisation affects the ratio of trans to cis somewhat. 

By the hydrogenation of BD/IP-copolymer feedstocks fully and partially hydrogenated rubbers with low crystallinities and low glass transition temperatures are obtained. For the preparation of highly amorphous hydrogenated rubbers a random copolymer composition is essential. In this respect feedstock preparation by the use of the Nd-carboxylate-based system NdV/DIBAH/EASC yielded better results than BD/IP copolymer feedstocks prepared by anionic polymerization with BuLi [484,485]. 

This method is used to form a block copolymer, which consists of two segments of essentially homopolymeric stracture separated by a block of a tapered segment of random copolymer composition. These are usually prepared by taking advantage of the differences in reaction rates of the component monomers. When polymerized individually in hexane, butadiene reacts six times more slowly than styrene however, when styrene and butadiene are copolymerized in a hydrocarbon solvent such as hexane, the reaction rates reverse, and the butadiene becomes six times faster than the styrene. This leads to a tapering of the styrene in a copolymerization reaction. For more details on the synthesis techniques, refer to Chapters 2 and 13. 

Figure 2.13. The modulus-temperature or modulus-negative frequency plots of the several random copolymer compositions and blends. The blend is predicted to exhibit a very broad glass transition, in comparison with the corresponding random copolymers. (Takayanagi et ai, 1963.)...

The PVC/NBR-40 system shows a third distinct type of behavior, somewhat reminiscent of the behavior of random copolymer compositions... 

A series of poly(aryloxyphosphazene)s has been prepared with phenoxy and p-ethylphenoxy substituents in varying ratios. The thermal, morphological, and rheological properties of this series were studied and the data were found to be consistent with the behaviour expected of a random copolymer composition. The thermal transition behaviour of blends of poly(aryloxyphosphazene) copolymers... 

Chen H, Choi J.H., Salas-de -la Cruz D., Winey KI. Elab Y.A. (2009). Polymerized Ionic Liquids the effect of random copolymer composition on ion conduction. Macromolecules, vol.42, n°13, pp.4809-4816, (May 2009), ISSN 0024-9297... 

Styrene-Acrylonitrile (SAN) Copolymers. SAN resins are random, amorphous copolymers whose properties vary with molecular weight and copolymer composition. An increase in molecular weight or in acrylonitrile content generally enhances the physical properties of the copolymer but at some loss in ease of processing and with a slight increase in polymer color. 

Hexafluoiopiopylene and tetiafluoioethylene aie copolymerized, with trichloiacetyl peroxide as the catalyst, at low temperature (43). Newer catalytic methods, including irradiation, achieve copolymerization at different temperatures (44,45). Aqueous and nonaqueous dispersion polymerizations appear to be the most convenient routes to commercial production (1,46—50). The polymerization conditions are similar to those of TFE homopolymer dispersion polymerization. The copolymer of HFP—TFE is a random copolymer that is, HFP units add to the growing chains at random intervals. The optimal composition of the copolymer requires that the mechanical properties are retained in the usable range and that the melt viscosity is low enough for easy melt processing. 

In order to achieve the desired fiber properties, the two monomers were copolymerized so the final product was a block copolymer of the ABA type, where A was pure polyglycoHde and B, a random copolymer of mostly poly (trimethylene carbonate). The selected composition was about 30—40% poly (trimethylene carbonate). This suture reportedly has exceUent flexibiHty and superior in vivo tensile strength retention compared to polyglycoHde. It has been absorbed without adverse reaction ia about seven months (43). MetaboHsm studies show that the route of excretion for the trimethylene carbonate moiety is somewhat different from the glycolate moiety. Most of the glycolate is excreted by urine whereas most of the carbonate is excreted by expired CO2 and uriae. 

The glass transition temperature of a random copolymer usually falls between those of the corresponding homopolymers since the copolymers will tend to have intermediate chain stiffness and interchain attraction. Where these are the only important factors to be considered a linear relationship between Tg and copolymer composition is both reasonable to postulate and experimentally verifiable. One form of this relationship is given by the equation... 

Mangipudi et al. [63,88] reported some initial measurements of adhesion strength between semicrystalline PE surfaces. These measurements were done using the SFA as a function of contact time. Interestingly, these data (see Fig. 22) show that the normalized pull-off energy, a measure of intrinsic adhesion strength is increased with time of contact. They suggested the amorphous domains in PE could interdiffuse across the interface and thereby increase the adhesion of the interface. Falsafi et al. [37] also used the JKR technique to study the effect of composition on the adhesion of elastomeric acrylic pressure-sensitive adhesives. The model PSA they used was a crosslinked network of random copolymers of acrylates and acrylic acid, with an acrylic acid content between 2 and 10%. 

The toughness of interfaces between immiscible amorphous polymers without any coupling agent has been the subject of a number of recent studies [15-18]. The width of a polymer/polymer interface is known to be controlled by the Flory-Huggins interaction parameter x between the two polymers. The value of x between a random copolymer and a homopolymer can be adjusted by changing the copolymer composition, so the main experimental protocol has been to measure the interface toughness between a copolymer and a homopolymer as a function of copolymer composition. In addition, the interface width has been measured by neutron reflection. Four different experimental systems have been used, all containing styrene. Schnell et al. studied PS joined to random copolymers of styrene with bromostyrene and styrene with paramethyl styrene [17,18]. Benkoski et al. joined polystyrene to a random copolymer of styrene with vinyl pyridine (PS/PS-r-PVP) [16], whilst Brown joined PMMA to a random copolymer of styrene with methacrylate (PMMA/PS-r-PMMA) [15]. The results of the latter study are shown in Fig. 9. 

Benkoski, J.J., Fredrickson, G.H. and Kramer, E.J., The effect of composition drift on the effectiveness of random copolymer reinforcement at polymer-polymer interfaces. Macromolecules (2001, in press). 

Figure 3.10 Melting temperatures of caprolactam-caprolactone random copolymers as function of molar composition.22...

The value of the reachvity rahos is crihcal in determining the composition of the copolymer. If the reactivity raho is greater than 1, the radical prefers to react with chains having the same kind of terminal unit, e.g. A- with A. On the other hand, if the reactivity ratio is less than 1, the monomer prefers to react with chains which end in the other kind of monomer. In the special case that r r2 = 1, the reaction is described as ideal copolymerisation because it results in a truly random copolymer whose composition is the same as the composition of the reaction mixture from which polymerisation took place. 

Sequence length distributions are occasionally important. They measure the occurrences of structures like YXY, YXXY, and YXXXY in a random copolymer. These can be calculated from the reactivity ratios and the polymer composition. See, for example. Ham. ... 

Determine the copolymer composition for a styrene-acrylonitrile copolymer made at the azeotrope (62 mol% styrene). Assume = 1000. One approach is to use the Gaussian approximation to the binomial distribution. Another is to synthesize 100,000 or so molecules using a random number generator and to sort them by composition. 

An N-vinylpyrrolidone/acrylamide random copolymer (0.05% to 5.0% by weight) is used for cementing compositions [371, 1076]. Furthermore, a sulfonate-containing cement dispersant is necessary. The additive can be used in wells with a bottom-hole temperature of 80° to 300° F. The fluid loss additive mixture is especially effective at low temperatures, for example, below 100° F and in sodium silicate-extended slurries. 

The type of copolymer formed during step growth polymerization depends on the reactivity of the functional groups and the time of introduction of the comonomer. A random copolymer forms when equal concentrations of equally reactive monomers polymerize. The composition of the copolymer, then, will be the same as the composition of the reactants prior to polymerization. When the reactivities of the monomers-differ, the more highly reactive monomer reacts first, creating a block consisting predominandy of one monomer in the chain the lower reactivity monomer is added later. This assumes that there is no chain transfer and no monofunctional monomer present. If either of these conditions were to exist,... 

Butadiene-Styrene Copolymers from Ba-Mg-Al Catalyst Systems. Figure 13 shows the relationship between copolymer composition and extent of conversion for copolymers of butadiene and styrene (25 wt.7. styrene) prepared in cyclohexane with Ba-Mg-Al and with n-BuLi alone. Copolymerization of butadiene and styrene with barium salts and Mg alkyl-Al alkyl exhibited a larger initial incorporation of styrene than the n-BuLi catalyzed copolymerization. A major portion of styrene placements in these experimental SBR s are more random however, a certain fraction of the styrene sequences are present in small block runs. 

---