Pyrolysis comparison

Saiz-Jimenez C., Boon J. J., Hedges J. L, Hessels J. K. C., and de Leeuw J. W. (1987) Chemical characterization of recent and buried woods by analytical pyrolysis comparison of... 

Figure 9. Approximate levels of two major surface reactions during ethane pyrolysis comparison of experimental results in metal reactors...

Analytical investigations may be undertaken to identify the presence of an ABS polymer, characterize the polymer, or identify nonpolymeric ingredients. Fourier transform infrared (ftir) spectroscopy is the method of choice to identify the presence of an ABS polymer and determine the acrylonitrile—butadiene—styrene ratio of the composite polymer (89,90). Confirmation of the presence of mbber domains is achieved by electron microscopy. Comparison with available physical property data serves to increase confidence in the identification or indicate the presence of unexpected stmctural features. Identification of ABS via pyrolysis gas chromatography (91) and dsc ((92) has also been reported. 

Sihcon carbide is also a prime candidate material for high temperature fibers (qv). These fibers are produced by three main approaches polymer pyrolysis, chemical vapor deposition (CVD), and sintering. Whereas fiber from the former two approaches are already available as commercial products, the sintered SiC fiber is still under development. Because of its relatively simple process, the sintered a-SiC fiber approach offers the potential of high performance and extreme temperature stabiUty at a relatively low cost. A comparison of the manufacturing methods and properties of various SiC fibers is presented in Table 4 (121,122). 

A pyrolysis technique was investigated as a method for the chemical recycling of glass fibre-reinforced unsaturated polyester SMC composites. The proeess yielded liquid products and gases and also a solid residue formed in the pyrolysis of glass fibres and fillers. The solid residue was used as a reinforeement/filler in unsaturated polyester BMC composites, and the influenee on mechanical properties was studied in comparison with BMC prepared entirely from virgin materials. 

Comparison of catalytic pyrolysis with non-catalytic pyrolysis... 

The effect of TOS on the product distribution during the pyrolysis of R22 over CU-AIF3 catalyst is shown in Fig. 3. The amoimt of halogen ion trapped in NaOH solution was determined by IC. The concentration of Cl formed during the pyrolysis of R22 was higher than the concentration of F at all TOS. This result is a consequence of the facile cleavage of the C-Cl bond in comparison to the C-F bond. Bond dissociation energy for the C-element of R22 is followed by the order C-C1[Pg.235]

Fig. 6. Comparison of initial rate with titama particles prepared by flame spray pyrolysis and spray pyrolysis.

Nowadays silenes are well-known intermediates. A number of studies have been carried out to obtain more complex molecules having Si=C double bonds. Thus, an attempt has been made to generate and stabilize in a matrix 1,1-dimethyl-l-silabuta-l,3-diene [125], which can be formed as a primary product of pyrolysis of diallyldimethylsilane [126] (Korolev et al., 1985). However, when thermolysis was carried out at 750-800°C the absorptions of only two stable molecules, propene and 1,1-dimethylsilacyclobut-2-ene [127], were observed in the matrix IR spectra of the reaction products. At temperatures above 800°C both silane [126] and silacyclobutene [127] gave low-molecular hydrocarbons, methane, acetylene, ethylene and methylacetylene. A comparison of relative intensities of the IR... 

Alternative approaches consist in heat extraction by means of thermal analysis, thermal volatilisation and (laser) desorption techniques, or pyrolysis. In most cases mass spectrometric detection modes are used. Early MS work has focused on thermal desorption of the additives from the bulk polymer, followed by electron impact ionisation (El) [98,100], Cl [100,107] and field ionisation (FI) [100]. These methods are limited in that the polymer additives must be both stable and volatile at the higher temperatures, which is not always the case since many additives are thermally labile. More recently, soft ionisation methods have been applied to the analysis of additives from bulk polymeric material. These ionisation methods include FAB [100] and LD [97,108], which may provide qualitative information with minimal sample pretreatment. A comparison with FAB [97] has shown that LD Fourier transform ion cyclotron resonance (LD-FTTCR) is superior for polymer additive identification by giving less molecular ion fragmentation. While PyGC-MS is a much-used tool for the analysis of rubber compounds (both for the characterisation of the polymer and additives), as shown in Section 2.2, its usefulness for the in situ in-polymer additive analysis is equally acknowledged. 

Freeman, R. Gould, F. K. Wilkinson, R. Ward, A. C. Lightfoot, N. F. Sisson, P. R. Rapid inter-strain comparison by pyrolysis mass spectrometry of coagulase-negative staphylococci from persistent CAPD peritonitits. Epidemiol. Infect. 1991, 106,239-246. 

Goodfellow, M. Inter-strain comparison of pathogenic microorganisms by pyrolysis mass spectrometry. Binary Comput. Microbiol. 1995, 7, 54-60. 

O Neill, G. L. Brazier, J. S. Magee, J. T. Duerden, B. I. A comparison of PCR ribotyping and pyrolysis mass spectrometry for typing clinical isolates of Clostridium difficile. Anaerobe 1996, 2, 211-215. 

On heating in air at 10°C per min, poly(m-carborane-siloxane) shows typically only 4% mass loss at 450°C and 7% mass loss at 600°C (see Fig. 4). In comparison, siloxanes without carborane units, show an approximate 50% mass loss at 450°C. As a consequence of the relatively high boron and carbon content of these materials, pyrolysis is expected to generate ceramic residues of boron carbide/silicon carbide. 

---