Process advantages and disadvantages

The process can be operated in two modes co-fed and redox. The co-fed mode employs addition of O2 to the methane/natural gas feed and subsequent conversion over a metal oxide catalyst. The redox mode requires the oxidant to be from the lattice oxygen of a reducible metal oxide in the reactor bed. After methane oxidation has consumed nearly all the lattice oxygen, the reduced metal oxide is reoxidized using an air stream. Both methods have processing advantages and disadvantages. In all cases, however, the process is mn to maximize production of the more desired ethylene product. 

Hignett, T. P. Nitrophosphate Process Advantages and Disadvantages, in Proc. I5th Annual Meeting Fert. Ind. Round Table, pp. 92-95, 1965. 

US Environmental Protection Agency has compared ultraviolet radiation with other disinfection processes in terms of their technological status (Table 5), disinfectant production (Table 6), operation and maintenance (Table 7), process advantages and disadvantages (Table 8), and applicahon points (Table 9). 

Both oleochemical routes have process advantages and disadvantages, and both produce high-quality primary alcohols of even numbered carbon chain lengths. 

Table 7 is a comparison of some key process advantages and disadvantages for the technologies under consideration for hydrogen/carbon... 

There are advantages and disadvantages in both processes the solvent process requires no special equipment but uses an excess of benzene whose recovery adds to the cost of the product. The bad mill method uses no excess benzene but requires special equipment which has frequent mechanical problems. 

Each heating technique has its advantages and disadvantages, and changing from one technique to another may involve significant changes in the process variables. The cold-waH reactor is most often used in small-size systems. The hot-waH reactor, by contrast, is most often used in large-volume production reactors. 

In this work the state-of-the-art and perspectives of column characterization and compai ison have been presented and discussed. All information about physico-chemical properties of RP HPLC Cl8 and C8 columns as porosity, average surface area, free silanol concentration, binding ligand density and others, were summarized. The points of views about column classifications, its advantages and disadvantages were discussed. It was shown that Cl8 and C8 HPLC column classification processes do not allow selecting the column with the same or preai range selectivity. 

Protection with impressed current, with galvanic anodes, and a combination of both processes is used for marine structures and offshore pipelines. Their properties, as well as their advantages and disadvantages, are given in Table 16-1. The protective measures must be optimized for every structure. In the impressed current protection of offshore platforms, for example, the difficulties of maintenance and repair will be of major importance, whereas in harbor installations these problems can be... 

Deciding among a number of process options having inherent safety advantages and disadvantages with respect to different hazards can be quite difficult. The first step is to understand thoroughly all hazards associated with the process options. Process hazard analysis and evaluation techniques are appropriate tools (CCPS, 1992). These include ... 

There are advantages and disadvantages to each method of developing management process flow diagrams. 

PBAs are designed explicitly to meet the needs of specific applications on the basis of their property-processing-cost performances. One polymer is incorporated into the matrix of other polymers to impart specific characteristics as per the requirement along with the appropriate compatibilizer to ensure stress transfer in between phases. The polymer blend constituents and composition must, therefore, be selected on the basis of the compensation of properties, considering the advantages and disadvantages associated with each phase. Table 12 indicates some of the components used as modifiers. 

A snap joint is economical in two respects it allows the structural member to be molded simultaneously with the molded product, and it allows rationalizing the assembly, compared with such other joining processes as screws. Table 3-4 provides a comparison of its advantages and disadvantages. Some examples of the various types and their design considerations are shown in Figs. 3-23 to 3-25. 

Film and sheet can, in principal, be made by calendering or by extrusion. Factors that govern the advantages and disadvantages (limitations) of each process can interact in a complex way. Factors to be considered include (1) type of material to be processed, (2) quantity of product to be produced, (3) thickness... 

---