Powdered solids

Dye adsorption from solution may be used to estimate the surface area of a powdered solid. Suppose that if 3.0 g of a bone charcoal is equilibrated with 100 ml of initially 10 Af methylene blue, the final dye concentration is 0.3 x 10 Af, while if 6.0 g of bone charcoal had been used, the final concentration would have been 0.1 x Qr M. Assuming that the dye adsorption obeys the Langmuir equation, calculate the specific surface area of the bone charcoal in square meters per gram. Assume that the molecular area of methylene blue is 197 A. ... 

Because of their prevalence in physical adsorption studies on high-energy, powdered solids, type II isotherms are of considerable practical importance. Bmnauer, Emmett, and Teller (BET) [39] showed how to extent Langmuir s approach to multilayer adsorption, and their equation has come to be known as the BET equation. The derivation that follows is the traditional one, based on a detailed balancing of forward and reverse rates. 

Amount of material required. It is convenient to employ an arbitrary ratio of 0 10 g. of solid or 0 20 ml. of liquid for 3 0 ml. of solvent. Weigh out 0 10 g. of the finely-powdered solid to the nearest 0 01 g. after some experience, subsequent tests with the same compound may be estimated by eye. Measure out 0-20 ml. of the liquid either with a calibrated dropper (Fig. 11,27, 1) or a small graduated pipette. Use either a calibrated dropper or a graduated pipette to deliver 3 0 ml. of solvent. Rinse the delivery pipette with alcohol, followed by ether each time that it is used. 

Horizontal-Tank Type This type (Fig. ll-56a) is used to transfer heat for melting or cooking diy powdered solids, rendering lard from meat-scrap solids, and drying divided solids. Heat-transfer coefficients are 17 to 85 W/(m °C) [3 to 15 Btu/(h fF °F)] for drying and 28 to 140 W/(m °C) [5 to 25 Btu/(h fF °F)] for vacuum and/or solvent recovery. 

The small-spiral-large-sbaft type (Fig. ll-60b) is inserted in a solids-product line as pipe banks are in a fluid line, solely as a heat-transfer device. It features a thin burden ring carried at a high rotative speed and subjected to two-sided conductance to yield an estimated heat-transfer coefficient of 285 W/(m °C) [50 Btu/(h fU °F)], thereby ranking thermally next to the sheU-fluidizer type. This device for powdered solids is comparable with the Votator ol the fluid field. 

Incorporation of powdered solid carbon dioxide which volatilises at elevated temperatures. This process has been used in conjunction with PVC pastes. 

Before powdered carbon can be used commercially or reused for tertiary treatment of sewage effluents, a method of regeneration is required. The use of the fluidized bed for regeneration offers the key advantages of excellent temperature and atmosphere control and the ability to process the powdered solids conveniently and continuously. 

Observable Characteristics - Physical State (as shipped) Granular or powdered solid some may appear glassy Color. White Odor. None. 

Cs NMR results for Cs on the surfaces of illite, kaolinite, boehmite and silica gel (Figure 3) show that for this large, low charge cation the surface behavior is quite similar to the interlayer behavior. They also illustrate the capabilities of NMR methods to probe surface species and the effects of RH on the structural environments and dynamical behavior of the Cs. The samples were prepared by immersing 0.5 gm of powdered solid in 50 ml of O.IM CsCl solution at 2 5°C for 5 days. Final pHs were between 4.60 and 7.77, greater than the zero point of charge, except for boehmite, which has a ZPC... 

Procedure. The cold bismuth nitrate solution, containing 0.1-0.15 g of Bi (Note 1), must be slightly acid with nitric acid (Note 2), and occupy a volume of about 20 mL. Add finely powdered solid potassium iodide, slowly and with stirring, until the supernatant liquid above the black precipitate of bismuth tri-iodide is just coloured yellow (due to K[BiI4]). Dilute to 200mL with boiling water, and boil for a few minutes. The black tri-iodide is converted into... 

The Karl Fischer procedure was applied to the determination of water present in hydrated salts or adsorbed on the surface of solids. The procedure, where applicable, was more rapid and direct than the commonly used drying process. A sample of the finely powdered solid, containing 5-10 millimoles (90-180 mg) of water, was dissolved or suspended in 25 mL of dry methanol in a 250-mL glass-stoppered graduated flask. The mixture was titrated with standard Karl Fischer reagent to the usual electrometric end point. A blank titration was also carried out on a 25 mL sample of the methanol used to determine what correction (if any) needed to be applied to the titre obtained with the salt. 

A finely powdered solid sample of an osmium oxide (which melts at 40. °C and boils at 130.°C) with a mass of 1.509 g is placed into a cylinder with a movable piston that can expand against the atmospheric pressure of 745 Torr. Assume that the amount of residual air initially present in the cylinder is negligible. When the sample is heated to 200.°C, it is completely vaporized and the volume of the cylinder expands by 235 mL. What is the molar mass of the oxide Assuming that the oxide is OsOv, find the value of x. 

Oxysalt bonded cements are formed by acid-base reactions between a metal oxide in powdered solid form and aqueous solutions of metal chloride or sulphate. These reactions typically give rise to non-homo-geneous materials containing a number of phases, some of which are crystalline and have been well-characterized by the technique of X-ray diffraction. The structures of the components of these cements and the phase relationships which exist between them are complex. However, as will be described in the succeeding parts of this chapter, in many cases there is enough knowledge about these cements to enable their properties and limitations to be generally understood. 

Other properties Munsell color yellow-orange powdered solid density 1.41 g mL log Kan 4.1, thermally stable... 

Aid in the uniform dispersion of additives. Make powdered solids (e.g. particulate fillers with high energy and hydrophilic surface) more compatible with polymers by coating their surfaces with an adsorbed layer of surfactant in the form of a dispersant. Surface coating reduces the surface energy of fillers, reduces polymer/filler interaction and assists dispersion. Filler coatings increase compound cost. Fatty acids, metal soaps, waxes and fatty alcohols are used as dispersants commonly in concentrations from 2 to 5 wt %. 

MIXING AND DISPERSION OF VISCOUS LIQUIDS AND POWDERED SOLIDS ... 

Mixing and dispersion of viscous fluids—blending in the polymer processing literature—is the result of complex interaction between flow and events occurring at drop length-scales breakup, coalescence, and hydrodynamic interactions. Similarly, mixing and dispersion of powdered solids in viscous liquids is the result of complex interaction between flow and... 

---