Polyolefins propylene

Polyolefins. In these thermoplastic elastomers the hard component is a crystalline polyolefin, such as polyethylene or polypropylene, and the soft portion is composed of ethylene-propylene rubber. Attractive forces between the rubber and resin phases serve as labile cross-links. Some contain a chemically cross-linked rubber phase that imparts a higher degree of elasticity. 

Cyclic Polyolefins (GPO) and Gycloolefin Copolymers (GOG). Japanese and European companies are developing amorphous cycHc polyolefins as substrate materials for optical data storage (213—217). The materials are based on dicyclopentadiene and/or tetracyclododecene (10), where R = H, alkyl, or COOCH. Products are formed by Ziegler-Natta polymerization with addition of ethylene or propylene (11) or so-called metathesis polymerization and hydrogenation (12), (101,216). These products may stiU contain about 10% of the dicycHc stmcture (216). 

The use of TAG as a curing agent continues to grow for polyolefins and olefin copolymer plastics and mbbers. Examples include polyethylene (109), chlorosulfonated polyethylene (110), polypropylene (111), ethylene—vinyl acetate (112), ethylene—propylene copolymer (113), acrylonitrile copolymers (114), and methylstyrene polymers (115). In ethylene—propylene copolymer mbber compositions. TAG has been used for injection molding of fenders (116). Unsaturated elastomers, such as EPDM, cross link with TAG by hydrogen abstraction and addition to double bonds in the presence of peroxyketal catalysts (117) (see Elastol rs, synthetic). 

Polyolefins. The most common polyolefin used to prepare composites is polypropylene [9003-07-0] a commodity polymer that has been in commercial production for almost 40 years following its controlled polymerisation by Natta in 1954 (5). Natta used a Ziegler catalyst (6) consisting of titanium tetrachloride and an aluminum alkyl to produce isotactic polypropylene directly from propylene ... 

In the early stages of development of polypropylene rubbers, particularly butyl rubber, were used to reduce the brittleness of polypropylene. Their use declined for some years with the development of the polypropylene copolymers but interest was greatly renewed in the 1970s. This interest has been centred largely around the ethylene-propylene rubbers which are reasonably compatible in all proportions with polypropylene. At first the main interest was with blends in which the rubber content exceeded 50% of the blend and such materials have been designated as thermoplastic polyolefin elastomers (discussed in Section 11.9.1). There is also increasing interest in compounds with less than 50% rubber, often referred to as elastomer-modified thermoplastics. It is of interest to note... 

The minimum service temperature is determined primarily by the Tg of the soft phase component. Thus the SBS materials ctm be used down towards the Tg of the polybutadiene phase, approaching -100°C. Where polyethers have been used as the soft phase in polyurethane, polyamide or polyester, the soft phase Tg is about -60°C, whilst the polyester polyurethanes will typically be limited to a minimum temperature of about 0°C. The thermoplastic polyolefin rubbers, using ethylene-propylene materials for the soft phase, have similar minimum temperatures to the polyether-based polymers. Such minimum temperatures can also be affected by the presence of plasticisers, including mineral oils, and by resins if these become incorporated into the soft phase. It should, perhaps, be added that if the polymer component of the soft phase was crystallisable, then the higher would also affect the minimum service temperature, this depending on the level of crystallinity. 

A manufacturer considering using a thermoplastic elastomer would probably first consider one of the thermoplastic polyolefin rubbers or TPOs, since these tend to have the lowest raw polymer price. These are mainly based on blends of polypropylene and an ethylene-propylene rubber (either EPM or EPDM) although some of the polypropylene may be replaeed by polyethylene. A wide range of blends are possible which may also contain some filler, oil and flame retardant in addition to the polymers. The blends are usually subject to dynamic vulcanisation as described in Section 11.9.1. 

Figure 2 Light permeability of polyolefins after quenching (1-4) and of nonquenched samples (l -4 ) l,l -poly-propylene (PP) 2,2 -high-pressure polyethylene (HPPE) 3,3 -low-pressure polyethylene (LPPE) 4,4 -medium-pres-sure polyethylene (MPPE). Film thickness-150 fic moulding time-10 minutes, moulding pressure HPPE-160°C LPPE, MPPE, PP-190-200X.

Currently, important TPE s include blends of semicrystalline thermoplastic polyolefins such as propylene copolymers, with ethylene-propylene terepolymer elastomer. Block copolymers of styrene with other monomers such as butadiene, isoprene, and ethylene or ethylene/propy-lene are the most widely used TPE s. Styrene-butadiene-styrene (SBS) accounted for 70% of global styrene block copolymers (SBC). Currently, global capacity of SBC is approximately 1.1 million tons. Polyurethane thermoplastic elastomers are relatively more expensive then other TPE s. However, they are noted for their flexibility, strength, toughness, and abrasion and chemical resistance. Blends of polyvinyl chloride with elastomers such as butyl are widely used in Japan. ... 

Thermoplastic polyolefin rubbers are usually blends based on polypropylene and ethylene-propylene rubbers. They are not resistant to hydrocarbons. 

The use of pyrolysis for the recycling of mixed plastics is discussed and it is shown that fluidised bed pyrolysis is particularly advantageous. It is demonstrated that 25 to 45% of product gas with a high heating value and 30 to 50% of an oil rich in aromatics can be recovered. The oil is found to be comparable with that of a mixture of light benzene and bituminous coal tar. Up to 60% of ethylene and propylene can be produced by using mixed polyolefins as feedstock. It is suggested that, under appropriate conditions, the pyrolysis process could be successful commercially. 23 refs. 

FIGURE 6.3 The crystallinity and composition continuum for ethylene- and propylene-dominated polyolefins. Note the dispersion for the propylene-dominated polyolefins due to much-greater prevalence of blends and the presence of tacticity derived changes in crystallinity. 

The new polymers are intermediate in composition and crystallinity between the essentially amorphous EPR and the semicrystalhne iPP. The presence of the complementary blocks of elastomers for both ethylene and propylene crystallinity should not indicate a similarity, beyond the levels of the crystallinity in the properties of the E-plastomers and the P-plastomers. The E-plastomers and the P-plastomers differ in their stmctural, rheological, as well as their thermal, mechanical, and elastic properties. In a comparison of the tensile strength and tensile recovery (tension set) from a 100% elongation for a range of P-plastomers and E-plastomers, the former have lower tension set than EPR and iPP. However, for comparative E-plastomers and P-plastomers at equivalent tensile strength, the latter have significantly better tension set. In summary, P-plastomers are tough polyolefins which are uniquely soft and elastic. 

Polyamide/polyolefin modified with dicarboxylate (propylene-maleic anhydride) SBR—MA copolymer... 

Polymerised propylene, a polyolefin plastic with properties similar to those of polyethylene. Polypropylene Glycol (PPG)... 

Transition metal catalysis plays a key role in the polyolefin industry. The discovery by Ziegler and Natta of the coordination polymerization of ethylene, propylene, and other non-polar a-olefins using titanium-based catalysts, revolutionized the industry. These catalysts, along with titanium- and zirconium-based metallocene systems and aluminum cocatalysts, are still the workhorse in the manufacture of commodity polyolefin materials such as polyethylene and polypropylene [3-6],... 

---