Polymers classification molecular

The first chapter gives relevant information on thermoplastics and includes brief discussions of polymerization, molecular weight, molecular-weight distribution, polymer classification, polymer blends, and filled and recycled polymers. It also outlines the practical significance of melt rheology and the links it has with processing. 

Abstract Polymers are macromolecules derived by the combination of one or more chemical units (monomers) that repeat themselves along the molecule. The lUPAC Gold Book defines a polymer as A molecule of high relative molecular mass, the structure of which essentially comprises the multiple repetition of units derived, actually or conceptually, from molecules of low relative molecular mass. Several ways of classification can be adopted depending on their source (natural and synthetic), their structure (linear, branched and crosslinked), the polymerization mechanism (step-growth and chain polymers) and molecular forces (Elastomers, fibres, thermoplastic and thermosetting polymers). In this chapter, the molecular mechanisms and kinetic of polymer formation reactions were explored and particular attention was devoted to the main polymerization techniques. Finally, an overview of the most employed synthetic materials in biomedical field is performed. 

In the last section we examined some of the categories into which polymers can be classified. Various aspects of molecular structure were used as the basis for classification in that section. Next we shall consider the chemical reactions that produce the molecules as a basis for classification. The objective of this discussion is simply to provide some orientation and to introduce some typical polymers. For this purpose a number of polymers may be classified as either addition or condensation polymers. Each of these classes of polymers are discussed in detail in Part II of this book, specifically Chaps. 5 and 6 for condensation and addition, respectively. Even though these categories are based on the reactions which produce the polymers, it should not be inferred that only two types of polymerization reactions exist. We have to start somewhere, and these two important categories are the usual place to begin. 

In the second section a classification of the different kinds of polymorphism in polymers is made on the basis of idealized structural models and upon consideration of limiting models of the order-disorder phenomena which may occur at the molecular level. The determination of structural models and degree of order can be made appropriately through diffraction experiments. Polymorphism in polymers is, here, discussed only with reference to cases and models, for which long-range positional order is preserved at least in one dimension. 

The chemical and physical properties of the polymers obtained by these alternate methods are identical, except insofar as they are affected by differences in molecular weight. In order to avoid the confusion which would result if classification of the products were to be based on the method of synthesis actually employed in each case, it has been proposed that the substance be referred to as a condensation polymer in such instances, irrespective of whether a condensation or an addition polymerization process was used in its preparation. The cyclic compound is after all a condensation product of one or more bifunctional compounds, and in this sense the linear polymer obtained from the cyclic intermediate can be regarded as the polymeric derivative of the bifunctional monomer(s). Furthermore, each of the polymers listed in Table III may be degraded to bifunctional monomers differing in composition from the structural unit, although such degradation of polyethylene oxide and the polythioether may be difficult. Apart from the demands of any particular definition, it is clearly desirable to include all of these substances among the condensation... 

The foregoing discussion has shown that termination reactions in cationic polymerization may be of many different kinds, that they may differ for apparently closely related systems, and that they may even be entirely absent. However, the polymers produced in many of these reactions are of low molecular weight and this means that transfer reactions are dominant. They may take on an even greater variety of forms than the termination reactions and their classification and discussion are still in an early stage of development. 

The study of the molecular weight of the intermediate course is an effective method for the classification of polymerization as chain or stepwise reaction. In Figure 3, the molecular weight of the obtained polymer is plotted against the yield, for the oxidative polymerization of dimethylphenol with the copper catalyst and for the electro-oxidative polymerization. The molecular weight rises sharply in the last stage of the reaction for the copper-catalyzed polymerization. This behavior is explained by a stepwise growth mechanism. 

Different classifications for the chiral CSPs have been described. They are based on the chemical structure of the chiral selectors and on the chiral recognition mechanism involved. In this chapter we will use a classification based mainly on the chemical structure of the selectors. The selectors are classified in three groups (i) CSPs with low-molecular-weight selectors, such as Pirkle type CSPs, ionic and ligand exchange CSPs, (ii) CSPs with macrocyclic selectors, such as CDs, crown-ethers and macrocyclic antibiotics, and (iii) CSPs with macromolecular selectors, such as polysaccharides, synthetic polymers, molecular imprinted polymers and proteins. These different types of CSPs, frequently used for the analysis of chiral pharmaceuticals, are discussed in more detail later. 

Since the unit —(-NH-CHR-CO-) is obtained from a single monomer unit, it is a homopolymer. On the basis of molecular forces present between the chains of various polymers, the classification of pol3aners is given as follows. 

The classification of polymers according to polymerization mechanism, like that by structure and composition, is not without its ambiguities. Certain polymerizations show a linear increase of molecular weight with conversion (Fig. 1-lc) when the polymerization... 

Whether the formation of poly(p-xylylene) should be included in this chapter is not clear. Decisive data are not available to indicate the classification of this polymerization as a step or chain reaction. The formation of high polymer occurs instantaneously when p-xyly-lene contacts the cool surface, precluding the evaluation of polymer molecular weight versus conversion. Also, the mode of termination for this reaction is unknown. 

Various criteria can be considered in the classification of the SEC applications. The most important are the analytical SEC procednres. The preparative applications, which encompass the purification of complex samples before their further treatment, draw rather wide attention. In this latter case, analytes are preseparated by SEC according to the size of their components and either macromolecular or low molecular fractions are subject to further analyses by other methods. The production oriented SEC did not find wide application in the area of synthetic polymers due to both the high price of organic solvents and the ecological considerations. 

In addition to the classification of liquid chromatographic enantioseparation methods by technical description, these methods could further be classified according to the chemical structure of the diverse CSPs. The chiral selector moiety varies from large molecules, based on natural or synthetic polymers in which the chirality may be based on chiral subunits (monomers) or intrinsically on the total structure (e.g., helicity or chiral cavity), to low molecular weight molecules which are irreversibly and/or covalently bound to a rigid hard matrix, most often silica gel. 

Thus, polymers with mesogenic groups in side chains form structural mesophases of the same types as low-molecular liquid crystals. This makes it possible to apply traditional mesophase classification for the description of the structure of LC polymers. At the same time, the structure of some of comb-like polymers (see Table 5) considered as crystalline, may probably be treated as one of highly-ordered smectic mesophases (SH or Sj), whose study is only started74). 

---