Polyacrylonitrile carbon fibers

M. G. Dunham, Stabilisation of Polyacrylonitrile Carbon Fiber Precursors, Ph.D. dissertation, Clemson Urdversity, Clemson, S.C., May 1990. 

Dunham, M. G., Stabilization of polyacrylonitrile carbon fiber precursors. Ph.D. dissertation, Clemson University, Clemson, SC, 1990. 

Moon S C and Farris R J (2009) Strong electrospun nanometer-diameter polyacrylonitrile carbon fiber yarns. Carbon 47 2829-2839. 

For nosetip materials 3-directional-reinforced (3D) carbon preforms are formed using small cell sizes for uniform ablation and small pore size. Figure 5 shows typical unit cell dimensions for two of the most common 3D nosetip materials. Carbon-carbon woven preforms have been made with a variety of cell dimensions for different appHcations (27—33). Fibers common to these composites include rayon, polyacrylonitrile, and pitch precursor carbon fibers. Strength of these fibers ranges from 1 to 5 GPa (145,000—725,000 psi) and modulus ranges from 300 to 800 GPa. 

Process. Any standard precursor material can be used, but the preferred material is wet spun Courtaulds special acrylic fiber (SAF), oxidized by RK Carbon Fibers Co. to form 6K Panox B oxidized polyacrylonitrile (PAN) fiber (OPF). This OPF is treated ia a nitrogen atmosphere at 450—750°C, preferably 525—595°C, to give fibers having between 69—70% C, 19% N density less than 2.5 g/mL and a specific resistivity under 10 ° ohm-cm. If crimp is desired, the fibers are first knit iato a sock before heat treating and then de-knit. Controlled carbonization of precursor filaments results ia a linear Dow fiber (LDF), whereas controlled carbonization of knit precursor fibers results ia a curly carbonaceous fiber (EDF). At higher carbonizing temperatures of 1000—1400°C the fibers become electrically conductive (22). 

The property of mesophase that makes it suitable for carbon fiber and premium coke manufacture is that it forms ordered stmctures under stress which persist following carbonization. However, most carbon fiber production in the 1990s is based on polyacrylonitrile (PAN). 

More than 95% of current carbon fiber production for advanced composite appHcations is based on the thermal conversion of polyacrylonitrile (PAN) or pitch precursors to carbon or graphite fibers. Generally, the conversion of PAN or pitch precursor to carbon fiber involves similar process steps fiber formation, ie, spinning, stabilization to thermoset the fiber, carbonization—graphitization, surface treatment, and sizing. Schematic process flow diagrams are shown in Eigure 4. However, specific process details differ. 

W. Watt, "Chenhstry and Physics of the Conversion of Polyacrylonitrile Fibers into High Modulus Carbon Fibers," in Ref. 6. 

Polymers mesophase pitch polyacrylonitrile carbons" mesocarbon microbeads, carbon fibers PAN-based carbon fibers ... 

Because of their unique blend of properties, composites reinforced with high performance carbon fibers find use in many structural applications. However, it is possible to produce carbon fibers with very different properties, depending on the precursor used and processing conditions employed. Commercially, continuous high performance carbon fibers currently are formed from two precursor fibers, polyacrylonitrile (PAN) and mesophase pitch. The PAN-based carbon fiber dominates the ultra-high strength, high temperature fiber market (and represents about 90% of the total carbon fiber production), while the mesophase pitch fibers can achieve stiffnesses and thermal conductivities unsurpassed by any other continuous fiber. This chapter compares the processes, structures, and properties of these two classes of fibers. 

Low density, carbon fiber-carbon binder composites are fabricated from a variety of carbon fibers, including fibers derived from rayon, polyacrylonitrile (PAN), isotropic pitch, and mesophase pitch. The manufacture, structure, and properties of carbon fibers have been thoroughly reviewed elsewhere [3] and. therefore, are... 

Henrici-Olive, G. and Olive, S. The Chemistry of Carbon Fiber Formation from Polyacrylonitrile. Vol. 51, pp. 1—60. 

PAN-based carbon fiber processing flow chart, 26 731. See also Polyacrylonitrile (PAN)... 

CNF is an industrially produced derivative of carbon formed by the decomposition and graphitization of rich organic carbon polymers (Fig. 14.3). The most common precursor is polyacrylonitrile (PAN), as it yields high tensile and compressive strength fibers that have high resistance to corrosion, creep and fatigue. For these reasons, the fibers are widely used in the automotive and aerospace industries [1], Carbon fiber is an important ingredient of carbon composite materials, which are used in fuel cell construction, particularly in gas-diffusion layers where the fibers are woven to form a type of carbon cloth. 

Carbon fibers have been used as filaments for lamps for nearly a century, since Edison first used them. In the early 1960s, Shindo developed the first modern carbon fiber when he pyrolyzed polyacrylonitrile (PAN) fibers [5]. 

Fig. 2.8. Laser Raman spectra obtained (a) for a polyacrylonitrile (PAN)-based HMS4 carbon fiber, and (b) for a pitch-based P75S carbon fiber. After Robinson et al. (1987).

The surface properties of carbon fibers are intimately related to the internal structure of the fiber itself, which needs to be understood if the surface properties are to be modified for specific end applications. Carbon fibers have been made from a number of different precursors, including polyacrylonitrile (PAN), rayon (cellulose) and mesophase pitch. The majority of commercial carbon fibers currently produced are based on PAN, while those based on rayon and pitch are produced in very limited quantities for special applications. Therefore, the discussion of fiber surface treatments in this section is mostly related to PAN-based carbon fibers, unless otherwise specified. 

---