Poly potential

As a furtlier example for tire meaning of ex situ investigations of emersed electrodes witli surface analytical teclmiques, results obtained for tire double layer on poly crystalline silver in alkaline solutions are presented in figure C2.10.3. This system is of scientific interest, since tliin silver oxide overlayers (tliickness up to about 5 nm) are fonned for sufficiently anodic potentials, which implies tliat tire adsorjDtion of anions, cations and water can be studied on tire clean metal as well as on an oxide covered surface [55, 56]. For tire latter situation, a changed... 

PVF film for pLUORJNE CO POUNDS, ORGANIC - POLY(VINYL FLUORIDE)] (Vol 11) Greenhouse warming potential (GWP)... 

Structural Components. In most appHcations stmctural foam parts are used as direct replacements for wood, metals, or soHd plastics and find wide acceptance in appHances, automobUes, furniture, materials-handling equipment, and in constmction. Use in the huil ding and constmction industry account for more than one-half of the total volume of stmctural foam appHcations. High impact polystyrene is the most widely used stmctural foam, foUowed by polypropylene, high density polyethylene, and poly(vinyl chloride). The constmction industry offers the greatest growth potential for ceUular plastics. 

Applications. Polymers with small alkyl substituents, particularly (13), are ideal candidates for elastomer formulation because of quite low temperature flexibiUty, hydrolytic and chemical stabiUty, and high temperature stabiUty. The abiUty to readily incorporate other substituents (ia addition to methyl), particularly vinyl groups, should provide for conventional cure sites. In light of the biocompatibiUty of polysdoxanes and P—O- and P—N-substituted polyphosphazenes, poly(alkyl/arylphosphazenes) are also likely to be biocompatible polymers. Therefore, biomedical appHcations can also be envisaged for (3). A third potential appHcation is ia the area of soHd-state batteries. The first steps toward ionic conductivity have been observed with polymers (13) and (15) using lithium and silver salts (78). 

During the eady development of polycarbonates, many bisphenols were investigated for potential useftil products. Some of these monomers and polymers are hsted in Table 3. Despite this intensive search, however, no homopolycarbonates other than that of BPA have been produced. Copolymers and blends, on the other hand, have been quite successhil. Blends of polycarbonate with ABS and with poly(butylene terephthalate) (PBT in particular have shown significant growth since the mid-1980s. 

Recycled poly(ethylene terephthalate) (PET), which offers excellent properties at potentially lower cost, is finding wider use as a raw material component and meeting increasing demands for environmentally compatible resins (see POLYESTERS,THERMOPLASTIC Recycling, PLASTICS). 

Poly(ethylene oxide) associates in solution with certain electrolytes (48—52). For example, high molecular weight species of poly(ethylene oxide) readily dissolve in methanol that contains 0.5 wt % KI, although the resin does not remain in methanol solution at room temperature. This salting-in effect has been attributed to ion binding, which prevents coagulation in the nonsolvent. Complexes with electrolytes, in particular lithium salts, have received widespread attention on account of the potential for using these materials in a polymeric battery. The performance of soHd electrolytes based on poly(ethylene oxide) in terms of ion transport and conductivity has been discussed (53—58). The use of complexes of poly(ethylene oxide) in analytical chemistry has also been reviewed (59). 

Copolymers of S-caprolactone and L-lactide are elastomeric when prepared from 25% S-caprolactone and 75% L-lactide, and rigid when prepared from 10% S-caprolactone and 90% L-lactide (47). Blends of poly-DL-lactide and polycaprolactone polymers are another way to achieve unique elastomeric properties. Copolymers of S-caprolactone and glycoHde have been evaluated in fiber form as potential absorbable sutures. Strong, flexible monofilaments have been produced which maintain 11—37% of initial tensile strength after two weeks in vivo (48). 

There are numerous misconceptions about the sources of various chemical elements in waste, particularly those that are potential acid formers when the waste is incinerated or mechanically converted and used as a refuse-derived fuel. For example, it is often mistakenly stated that the source of chlorine in waste, hence a potential source of HCl emissions, is poly(vinyl chloride). The relative contents of selected, potentially acid-forming elements in the organic portion of a sample of waste collected from various households in one U.S. East Coast city is given in Table 2 (17). In this city, a chief source of chlorine in the waste is NaCl, probably from food waste. 

Some polymers from styrene derivatives seem to meet specific market demands and to have the potential to become commercially significant materials. For example, monomeric chlorostyrene is useful in glass-reinforced polyester recipes because it polymerizes several times as fast as styrene (61). Poly(sodium styrenesulfonate) [9003-59-2] a versatile water-soluble polymer, is used in water-poUution control and as a general flocculant (see Water, INDUSTRIAL WATER TREATMENT FLOCCULATING AGENTs) (63,64). Poly(vinylhenzyl ammonium chloride) [70304-37-9] h.a.s been useful as an electroconductive resin (see Electrically conductive polya rs) (65). 

Microstructure. Interest in PVP microstmcture and the potential for tacticity has been reviewed (39,40). PVP generated by free radicals has been shown to be atactic except when polymerization is conducted in water. In this case some syndiotacticity is observed (40). In the presence of syndiotactic templates of poly(methacryhc acid) (or poly(MAA)), VP will apparentiy polymerize with syndiotactic microstmcture, although proof is lacking (41—45). The reverse, polymerization of MAA in the presence of PVP, affords, as expected, atactic poly(MAA) (46,47). 

Polyarylether Ketones. The aromatic polyether ketones are tme thermoplastics. Although several are commercially available, two resins in particular, poly ether ether ketone [31694-16-3] (PEEK) from ICI and poly ether ketone ketone (PEKK) from Du Pont, have received most of the attention. PEEK was first synthesized in 1981 (20) and has been well studied it is the subject of numerous papers because of its potential use in high performance aircraft. Tough, semicrystalline PEEK is prepared by the condensation of bis(4-fiuorophenyl) ketone with the potassium salt of bis(4-hydroxyphenyl) ketone in a diaryl sulfone solvent, such as diphenyl sulfone. The choice of solvent is critical other solvents, such as Hquid HE, promote the reaction but lead to premature low molecular-weight crystals, which do not exhibit sufficient toughness (21). 

Polyheterocycles. Heterocychc monomers such as pyrrole and thiophene form hiUy conjugated polymers (4) with the potential for doped conductivity when polymerization occurs in the 2, 5 positions as shown in equation 6. The heterocycle monomers can be polymerized by an oxidative coupling mechanism, which can be initiated by either chemical or electrochemical means. Similar methods have been used to synthesize poly(p-phenylenes). 

---