Mobilities poly

Another interesting applications area for fullerenes is based on materials that can be fabricated using fullerene-doped polymers. Polyvinylcarbazole (PVK) and other selected polymers, such as poly(paraphcnylene-vinylene) (PPV) and phenylmethylpolysilane (PMPS), doped with a mixture of Cgo and C70 have been reported to exhibit exceptionally good photoconductive properties [206, 207, 208] which may lead to the development of future polymeric photoconductive materials. Small concentrations of fullerenes (e.g., by weight) lead to charge transfer of the photo-excited electrons in the polymer to the fullerenes, thereby promoting the conduction of mobile holes in the polymer [209]. Fullerene-doped polymers also have significant potential for use in applications, such as photo-diodes, photo-voltaic devices and as photo-refractive materials. 

A SEC material should be hydrophilic if it is to be used for biological applications. One such material, introduced by PolyLC in 1990 (8), is silica with a covalently attached coating of poly(2-hydroxyethyl aspartamide) the trade name is PolyHYDROXYETHYL Aspartamide (PolyHEA). This material was evaluated for SEC of polypeptides by P.C. Andrews (University of Michigan) and worked well for the purpose (Fig. 8.1). Because formic acid is a good solvent for polypeptides, Dr. Andrews tried a mobile phase of 50 mM formic acid. The result was a dramatic shift to a lower fractionation range for both Vq and V, (Fig. 8.2) to the point that V, was defined by the elution position of water. 

FIGURE I 1.3 Analysis of poly(l, 4-butylene terephthalate) usinga Waters Alliance narrow-bore GPC system. Columns 4.6 X 300 mm Styragel HR 2, HR 3, and HR 4. Mobile phase hexafluoroisopropanol. 0.35 ml/min at 30 C. (Chromatogram courtesy of Peter Alden, Waters Corp.)... 

Commercial grades of PVP, K-15, K-30, K-90, and K-120 and the quaternized copolymer of vinylpyrrolidone and dimthylaminoethylmethacrylate (poly-VP/ DMAEMA) made by International Specialty Products (ISP) were used in this study. PEO standard calibration kits were purchased from Polymer Laboratories Ltd. (PL), American Polymer Standards Corporation (APSC), Polymer Standards Service (PSS), and Tosoh Corporation (TSK). In addition, two narrow NIST standards, 1923 and 1924, were used to evaluate commercial PEO standards. Deionized, filtered water, and high-performance liquid chromatography grade methanol purchased from Aldrich or Fischer Scientific were used in this study. Lithium nitrate (LiN03) from Aldrich was the salt added to the mobile phases to control for polyelectrolyte effects. 

The quaternized copolymer of vinylpyrrolidone and dimethylaminoethylmetha-crylate (poly-VP/DMAEMA) has been analyzed successfully with Ultrahydrogel columns and a mobile phase of a 0.1 M Tris pH 7 buffer with 0.3 or 0.5 M lithium nitrate (14). In this study, poor recovery of a poly-VP/DMAEMA sample was noticed when 0.2 M lithium nitrate was used for KB-80M, SB806-MHQ, and TSK GM-PWxl columns. Good recovery was achieved with 0.4 M lithium nitrate, and M of the poly-VP/DMAEMA were found to be 290,000, 300,000, and 320,000 for the respective columns. This demonstrates the equivalence of these columns for SEC of cationic polymers. 

TSK PWxL, Shodex OH-pak KB-80M, and SB806MHQ columns are equivalent for SEC of a quaternized poly-(VP/DMAEMA) in a pH 7 mobile phase. 

A commercially available cationic standard that can be used for the calibration of CATSEC columns is poly(2-vinyl pyridine), or PVP. Cationic PVP can be characterized easily on CATSEC columns over a broad range of molecular weight. DRI chromatograms of two cationic PVP standards using a bank of CATSEC columns (100-, 300-, 1000-, and 4000-A pore size) and a mobile phase of 0.05 N NaNOi/0.1% TFA are shown in Fig. 20.10. 

Figure 12.18 LC-SFC analysis of mono- and di-laurates of poly (ethylene glycol) ( = 10) in a surfactant sample (a) normal phase HPLC trace (b) chromatogram obtained without prior fractionation (c) chromatogram of fraction 1 (FI) (d) chromatogram of fraction 2 (F2). LC conditions column (20 cm X 0.25 cm i.d.) packed with Shimpak diol mobile phase, w-hexane/methylene chloride/ethanol (75/25/1) flow rate, 4 p.L/min UV detection at 220 nm. SFC conditions fused-silica capillary column (15 m X 0.1 mm i.d.) with OV-17 (0.25 p.m film thickness) Pressure-programmed at a rate of 10 atm/min from 80 atm to 150 atm, and then at arate of 5 atm/min FID detection. Reprinted with permission from Ref. (23).

Concerning the nature of electronic traps for this class of ladder polymers, we would like to recall the experimental facts. On comparing the results of LPPP to those of poly(para-phenylene vinylene) (PPV) [38] it must be noted that the appearance of the maximum current at 167 K, for heating rates between 0.06 K/s and 0.25 K/s, can be attributed to monomolecular kinetics with non-retrapping traps [26]. In PPV the density of trap states is evaluated on the basis of a multiple trapping model [38], leading to a trap density which is comparable to the density of monomer units and very low mobilities of 10-8 cm2 V-1 s l. These values for PPV have to be compared to trap densities of 0.0002 and 0.00003 traps per monomer unit in the LPPP. As a consequence of the low trap densities, high mobility values of 0.1 cm2 V-1 s-1 for the LPPPs are obtained [39]. 

We Finally note that the MTR model is a priori more appropriate to disordered materials. It is not expected to give good results with single crystal OFET, especially when the mobility becomes temperature-independent (see Section 14.6.1.2). However, it has recently been invoked in the case of poly thiophene [112], the mobility of which is also thermally activated. 

In the sol-gel procedure for the preparation of hybrids, polymeric acid catalysts such as poly (styrene sulfonic acid) were also used instead of hydrogen chloride [14]. The polymeric acid catalyst was effective for the preparation of hybrids at a similar level to that of hydrogen chloride catalyst. In some cases, the increased modulus was observed due to the higher extent of reaction. No difference was observed in morphologies between the hybrids prepared with polymeric and small molecule acid catalysts. The method using polymeric acid catalyst may depress the ion-conductive property, characteristic to the mobile acidic small molecules. Polymeric catalyst may also influence the rheology of the resulting hybrids. 

---