Poly groups

The second category of polymerization reactions does not involve a chain reaction and is divided into two groups poly addition and poly condensation [4]. In botli reactions, tire growth of a polymer chains proceeds by reactions between molecules of all degrees of polymerization. In polycondensations a low-molecular-weight product L is eliminated, while polyadditions occur witliout elimination ... 

Figure 12.1. Perfluoriiiated resinsulfonic acid similar to Nafion-H, showing clustering of SO3H groups PTFE = poly(tetrafluoroethylene).

FIGURE 7 16 Poly mers of propene The mam chain IS shown in a zigzag conformation Every other carbon bears a methyl sub stituent and is a chirality center (a) All the methyl groups are on the same side of the carbon chain in isotactic polypropylene (b) Methyl groups alternate from one side to the other in syndiotactic polypropy lene (c) The spatial orienta tion of the methyl groups IS random in atactic polypropylene... 

Commonly used isocyanates are toluene dhsocyanate, methylene diphenyl isocyanate, and polymeric isocyanates. Polyols used are macroglycols based on either polyester or polyether. The former [poly(ethylene phthalate) or poly(ethylene 1,6-hexanedioate)] have hydroxyl groups that are free to react with the isocyanate. Most flexible foam is made from 80/20 toluene dhsocyanate (which refers to the ratio of 2,4-toluene dhsocyanate to 2,6-toluene dhsocyanate). High-resilience foam contains about 80% 80/20 toluene dhsocyanate and 20% poly(methylene diphenyl isocyanate), while semi-flexible foam is almost always 100% poly(methylene diphenyl isocyanate). Much of the latter reacts by trimerization to form isocyanurate rings. 

A linear molecule has a carboxyl group at one end and an amino group at the other, such as poly(e-caprolactam) ... 

Strauss and Williamst have studied coil dimensions of derivatives of poly(4-vinylpyridine) by light-scattering and viscosity measurements. The derivatives studied were poly(pyridinium) ions quaternized y% with n-dodecyl groups and (1 - y)% with ethyl groups. Experimental coil dimensions extrapolated to 0 conditions and expressed relative to the length of a freely rotating repeat unit are presented here for the molecules in two different environments ... 

The hydrogens of the methylene group in the backbone of the poly (methyl methacrylate) produce a single peak in a racemic dyad, as illustrated by structure [XVI]. 

Table 9.3 lists the intrinsic viscosity for a number of poly(caprolactam) samples of different molecular weight. The M values listed are number average figures based on both end group analysis and osmotic pressure experiments. Tlie values of [r ] were measured in w-cresol at 25°C. In the following example we consider the evaluation of the Mark-Houwink coefficients from these data. 

Acetals are readily formed with alcohols and cycHc acetals with 1,2 and 1,3-diols (19). Furfural reacts with poly(vinyl alcohol) under acid catalysis to effect acetalization of the hydroxyl groups (20,21). Reaction with acetic anhydride under appropriate conditions gives the acylal, furfuryUdene diacetate... 

Fig. 4. Chemistry of poly(vinyl cinnamate) negative-acting resist. Initial light absorption by the photosensitizer is followed by energy transfer to produce a pendant cinnamate group in a triplet electronic state. This combines with a second cinnamate on another polymer chain, forming a polymer—polymer...

Four other groups of synthetic adhesives find uses in secondary processing, ie, overlaying, assembly gluing, etc, and in furniture and cabinet manufacture. Poly(vinyl acetate) (PVA) adhesives are widely used in appHcation of veneers and other overlays to panel substrates and in some unit-assembly operations. PVA adhesives are an emulsion of polyvinyl acetate in water and cure by loss of water. The PVA adhesives are somewhat... 

Another widely used overlay adhesive is the contact type. These specialized adhesives, in the same group as mbber cement, may be of the solvent-base or water-base types. They are often used to bond overlays such as wood veneer, vinyl (poly(vinyl chloride)) films, or high pressure laminates such as countertop overlays. 

This principle is illustrated in Figure 10 (45). Water adsorption at low pressures is markedly reduced on a poly(vinyhdene chloride)-based activated carbon after removal of surface oxygenated groups by degassing at 1000°C. Following this treatment, water adsorption is dominated by capillary condensation in mesopores, and the si2e of the adsorption-desorption hysteresis loop increases, because the pore volume previously occupied by water at the lower pressures now remains empty until the water pressure reaches pressures 0.3 to 0.4 times the vapor pressure) at which capillary condensation can occur. 

Until 1990 the EPA maintained a Hst of chemicals suitable for potable water treatment ia the United States. Siace then the entire question of certification and standards has been turned over to a group of organi2ations headed by the National Sanitation Eoundation, which has issued voluntary standards. As of January 1992, standards had been issued for most of the principal inorganic products, but only for two polymers, poly(DADMAC) and Epi-DMA (epichl orohydrin dimethyl amine) polymers (78). Certifications for commercial products meeting specified standards are issued by the National Sanitation Eoundation, Underwriter Laboratories, and Risk Eocus/Versar (79). 

Surface Protection. The surface properties of fluorosihcones have been studied over a number of years. The CF group has the lowest known intermolecular force of polymer substituents. A study (6) of liquid and solid forms of fluorosihcones has included a comparison to fluorocarbon polymers. The low surface tensions for poly(3,3,3-trifluoropropyl)methylsiloxane and poly(3,3,4,4,5,5,6,6,6-nonafluorohexyl)methylsiloxane both resemble some of the lowest tensions for fluorocarbon polymers, eg, polytetrafluoroethylene. 

---