Poly film polymerization

The ethylene glycol liberated by reaction (5.L) is removed by lowering the pressure or purging with an inert gas. Because the ethylene glycol produced by reaction (5.L) is removed, proper stoichiometry is assured by proceeding via the intermediate, bis(2-hydroxyethyl) terephthalate otherwise the excess glycol used initially would have a deleterious effect on the degree of polymerization. Poly(ethylene terephthalate) is more familiar by some of its trade names Mylar as a film and Dacron, Kodel, or Terylene as fibers it is also known by the acronym PET. 

Acrylics. Acetone is converted via the intermediate acetone cyanohydrin to the monomer methyl methacrylate (MMA) [80-62-6]. The MMA is polymerized to poly(methyl methacrylate) (PMMA) to make the familiar clear acryUc sheet. PMMA is also used in mol ding and extmsion powders. Hydrolysis of acetone cyanohydrin gives methacrylic acid (MAA), a monomer which goes direcdy into acryUc latexes, carboxylated styrene—butadiene polymers, or ethylene—MAA ionomers. As part of the methacrylic stmcture, acetone is found in the following major end use products acryUc sheet mol ding resins, impact modifiers and processing aids, acryUc film, ABS and polyester resin modifiers, surface coatings, acryUc lacquers, emulsion polymers, petroleum chemicals, and various copolymers (see METHACRYLIC ACID AND DERIVATIVES METHACRYLIC POLYMERS). 

Functionalized conducting monomers can be deposited on electrode surfaces aiming for covalent attachment or entrapment of sensor components. Electrically conductive polymers (qv), eg, polypyrrole, polyaniline [25233-30-17, and polythiophene/23 2JJ-J4-j5y, can be formed at the anode by electrochemical polymerization. For integration of bioselective compounds or redox polymers into conductive polymers, functionalization of conductive polymer films, whether before or after polymerization, is essential. In Figure 7, a schematic representation of an amperomethc biosensor where the enzyme is covalendy bound to a functionalized conductive polymer, eg, P-amino (polypyrrole) or poly[A/-(4-aminophenyl)-2,2 -dithienyl]pyrrole, is shown. Entrapment of ferrocene-modified GOD within polypyrrole is shown in Figure 7. 

LB films of CO-tricosenoic acid, CH2=CH—(CH2)2qCOOH, have been studied as electron photoresists (26—28). A resolution better than 50 nm could be achieved. Diacetylenic fatty acids have been polymerized to yield the corresponding poly (diacetylene) derivatives that have interesting third-order nonlinear optical properties (29). 

Poly(arylene vinylenes). The use of the soluble precursor route has been successful in the case of poly(arylene vinylenes), both those containing ben2enoid and heteroaromatic species as the aryl groups. The simplest member of this family is poly(p-phenylene vinylene) [26009-24-5] (PPV). High molecular weight PPV is prepared via a soluble precursor route (99—105). The method involves the synthesis of the bis-sulfonium salt from /)-dichloromethylbenzene, followed by a sodium hydroxide elimination polymerization reaction at 0°C to produce an aqueous solution of a polyelectrolyte precursor polymer (11). This polyelectrolyte is then processed into films, foams, and fibers, and converted to PPV thermally (eq. 8). 

Conducting polymer composites have also been formed by co-electrodeposition of matrix polymer during electrochemical polymerization. Because both components of the composite are deposited simultaneously, a homogenous film is obtained. This technique has been utilized for both neutral thermoplastics such as poly(vinyl chloride) (159), as well as for a large variety of polyelectrolytes (64—68, 159—165). When the matrix polymer is a polyelectrolyte, it serves as the dopant species for the conducting polymer, so there is an intimate mixing of the polymer chains and the system can be appropriately termed a molecular composite. 

By 1988, a number of devices such as a MOSFET transistor had been developed by the use of poly(acetylene) (Burroughes et al. 1988), but further advances in the following decade led to field-effect transistors and, most notably, to the exploitation of electroluminescence in polymer devices, mentioned in Friend s 1994 survey but much more fully described in a later, particularly clear paper (Friend et al. 1999). The polymeric light-emitting diodes (LEDs) described here consist in essence of a polymer film between two electrodes, one of them transparent, with careful control of the interfaces between polymer and electrodes (which are coated with appropriate films). PPV is the polymer of choice. 

Polymeric, prepared as thin smooth films (with the exception of poly(glycolic acid))... 

The strategy of Kaeriyama represents a so-called precursor route and was developed to overcome the characteristic shortcomings (insolubility, lack of process-ability) of previous PPP syntheses. The condensation reaction is carried out with solubilized monomers, leading to a soluble polymeric intermediate. In the final reaction step this intermediate is then converted, preferentially in the solid state allowing the formation of homogeneous PPP films or layers, into PPP (or other poly(arylene)s). 

The commercial polymeric films (Table I) that are used as the outside layer of multilayered materials for thermoprocessed food packaging are poly(ethylene terephthalate), polyiminocaproyl, or polypropylene. The other five films listed in Table I or polypropylene are used for the food-contacting layer. 

This means that we can follow the empirical kinetics of the electropolymerization process, at a constant overpotential (Fig. 6), by tracking the weight of the rinsed and dried polymer film,37 41 as we do in homogeneous polymerization processes of conducting or nonconducting poly-... 

Polymerization at constant current is most convenient for controlling the thickness of the deposited film. Charges of ca. 0.3, 0.2, and 0.08 C cm-2 are required to produce 1 fim of polypyrrole,59 poly(3-methylthio-phene)60 (no data are available for polythiophene), and polyaniline 43 respectively. Although these values can reasonably be used to estimate the thicknesses of most electrochemically formed conducting polymer films, it should be noted that they have considerable (ca. 30%) uncertainties. For each polymer, the relationship between charge and film thickness can... 

Figure 5. Cyclic voltammograms of (a) 2,5"" -di-methyl-a-hexathiophene and (b) poly(2,2 -bithio-phene) films in acetonitrile containing 0.1 M E NCIO 103 (Reprinted from G. Zotti, G. Schia-von, A. Berlin, and G. Pagani, Electrochemistry of end-ca )ed oligothienyls-new insights into the polymerization mechanism and the charge storage, conduction and capacitive properties of polythiophene, Synth. Met. 61 (1-2) 81-87, 1993, with kind permission from Elsevier Science S.A.)...

---